Konica Minolta FS-532 Manual de usuario

Table of Contents

Quick Guide

Ver. 01.00

- QG No. 04 -

Finishing Adjustment

(FS-532/FS-541 +PI-502/PK-522/SD-510)

Introduction

Staple Adjustment

Fold and Fold & Staple

Adjustment

Other Adjustments

Specifications

1Introduction

1-1. FS-532 and FS-541

FS-532 and FS-541 are "Flat binding machine equipped with staple cutting stapler".

They have a staple function by themselves.

Also, they have three types of sub-options.

•PostInserter [PI-502]

•Punch Unit [PK-522]

•Saddle Stitcher [SD-510]

Cover sheet

PostInserter [PI-502]

Insert sheet

Punch Unit [PK-522]

Punch (2 holes)

Saddle Stitcher [SD-510]

Multi Half Fold Fold & Staple Multi Tri-Fold

Stapler [FS-532/FS-541] + Sub-option functions

Staple function (Standard)

Main tray

(with alignment plate)

SD-510

Folder tray

Parallel

stapling

(front)

Parallel

stapling

(rear)

45-degree

stapling

(rear)

2-position

stapling

Wide

: 165 mm

Narrow

: 140 mm

Narrow+

: 120 mm

1Introduction

1-2. Types of Adjustment Functions

FS-532 and FS-541 have various adjustment functions.

For details on each adjustment function, refer to Chapters 2, 3, and 4.

Misalignment of stapled bundle

Horizontal

direction

Vertical

direction

Staple position and pitch

Staple position Pitch

Output without folding or stapling paper

(main tray)

Misalignment of

booklet pages

Short side direction

Booklet fold position

Punch hole positions

Horizontal

direction

Vertical

direction

Skew Horizontal

direction

Vertical

direction

Sound

Half-Fold fold

position

Booklet staple position and pitch

Pitch

Staple position

Fold & Staple fold

position

Strength of

half-fold booklet Tri-Fold fold positions

1st fold (inside) 2nd fold (outside)

2Staple Adjustment

2-1. Staple Adjustment Items

Staple is the FS-532/FS-541 standard function.

There are four types of staple-related adjustments.

The adjustments described in this chapter are only available for staple (Staple mode).

Misalignment of stapled bundle -1

Horizontal direction Adjustment to use: [Staple Paper Width Adj.]

Adjust the spacing of the horizontal alignment

plates when paper is loaded into the stacker.

Positive direction (+):

Widens the spacing of the horizontal

alignment plates.

Negative direction (-):

Narrows the spacing of the horizontal

alignment plates.

Vertical direction Adjustment to use: [FD Alignment Plate Adj.]

Adjust the pushing amount of the FD alignment

plate when paper is loaded into the stacker.

Positive direction (+):

Increases the pushing amount of the

FD alignment plate.

Negative direction (-):

Reduces the pushing amount of the

FD alignment plate.

(-) (+)

FD alignment

plate

Misalignment of stapled bundle -2

Each adjustment value described on this page is obtained by adding A to B (A + B).

•A= Offset adjustment value for all sizes (A)

•B= Adjustment value for each paper size (B)

Important

Horizontal

alignment

plates

04-010 Staple Paper Width Adj.

04-020 FD Alignment Plate Adj.

2Staple Adjustment

Staple position and staple pitch

Adjustment to use: [Staple Position Adjustment]

Adjust the 1-position staple position (front - rear).

The staple position can only be adjusted for 1-

position staple items.

Staple position

Rear

Diagonal

(-)

(+)

Rear

Parallel

(-)

(+)

Parallel in front

(-)

(+)

Positive direction (+):

The staple positions are away from

the horizontal edge of the paper.

Negative direction (-):

The staple positions are closer to the

horizontal edge of the paper.

Adjustment to use: [Staple Position Adjustment]

Adjust the 2-position staple pitch (spacing).

The staple pitch can only be adjusted for 2-

position staple items.

Staple pitch

2 Position Pitch

(120 mm, 140 mm, 165 mm)

(-)

Positive direction (+):

Widens the spacing between

2-position staple positions.

Negative direction (-):

Narrows the spacing between

2-position staple positions.

Pitch (+)

Each adjustment value described on this page is obtained by adding A to B (A + B).

•A= Offset adjustment value for all sizes (A)

•B= Adjustment value for each paper size (B)

Important

04-030 Staple Position Adjustment

3Fold and Fold & Staple Adjustment

Adjustment to use: [Half-Fold Fold Position Adj.]

Adjust the fold position in Multi Half Fold mode.

This adjustment is only available in Multi Half Fold

mode.

Half-Fold fold

position

Adjustment to use: [Fold&Staple Fold Position]

Adjust the fold position in Fold & Staple mode. The

staple position does not change (the staple position

can be changed with [Fold&Staple Staple Position]).

This adjustment is only available in Fold & Staple

mode.

Fold&Staple Staple

position

Half-Fold fold position and Fold & Staple fold position

3-1. Fold and Fold & Staple Adjustment Items

The Multi Half Fold and Fold & Staple functions are available when the saddle stitcher [SD-

510] is mounted.

There are eight types of Fold and Fold & Staple adjustments.

The adjustments described in this chapter are only available for Multi Half Fold, Fold &

Staple, and Multi Tri-Fold.

Positive direction (+):

Raises the folding position so that the top

surface of the output paper is short.

Negative direction (-):

Lowers the folding position so that the top

surface of the output paper is long.

Positive direction (+):

Raises the folding position so that the top

surface of the output paper is short.

Negative direction (-):

Lowers the folding position so that the top

surface of the output paper is long.

(+)

(-)

Top face of

output paper

(-)

Top face of

output paper

(+)

Each adjustment value described on this page is obtained by adding A to B (A + B).

•A= Offset adjustment value for all sizes (A)

•B= Adjustment value for each paper size (B)

Important

04-040 Half-Fold Fold Position Adj.

04-050 Fold&Staple Fold Position

3Fold and Fold & Staple Adjustment

Adjustment to use: [Fold&Staple Staple Position]

Adjust the staple position in Fold & Staple mode

and resolve the misalignment between the fold

position and the staple position. The fold position

does not change (the fold position can be changed

with [Fold&Staple Fold Position]).

This adjustment is only available in Fold & Staple

mode.

Staple position

Adjustment to use: [Fold&Staple Pitch Adjustment]

Adjust the pitch between Fold&Staple staple

positions.

This adjustment is only available in Fold&Staple

mode.

Pitch

Booklet staple position and pitch

Positive direction (+):

Raises the staple position so that the top

surface of the output paper is short.

Negative direction (-):

Lowers the staple position so that the top

surface of the output paper is long.

Positive direction (+):

Widens the pitch interval.

Negative direction (-):

Narrows the pitch interval.

Pitch

(+)

(-)

(+)

(-)

Each adjustment value described on this page is obtained by adding A to B (A + B).

•A= Offset adjustment value for all sizes (A)

•B= Adjustment value for each paper size (B)

Important

Top face of

output paper

04-060 Fold&Staple Staple Position

04-070 Fold&Staple Pitch Adjustment

3Fold and Fold & Staple Adjustment

Adjustment to use: [Fold&Staple Paper Width Adj.]

Adjust the spacing of the horizontal alignment

plates when paper is loaded into the stacker.

This adjustment is only available in Fold & Staple

mode.

Adjustment to use: [Half-Fold Strength Adj.]

Misalignment of booklet pages and strength of half-fold booklet

Misalignment of

booklet pages

Short side direction

Strength of

half-fold booklet

Positive direction (+):

Widens the spacing of the horizontal

alignment plates.

Negative direction (-):

Narrows the spacing of the horizontal

alignment plates.

(-) (+)

Positive (+) adjustment:

Increases the pressing time.

Increased pressing time, reduces productivity.

General precaution

Side view of

the booklet

Adjust the length of time the roller presses the

spine of the booklet.

This adjustment is only available in Fold &

Staple mode or Multi Half Fold mode.

Each adjustment value described on this page is obtained by adding A to B (A + B).

•A= Offset adjustment value for all sizes (A)

•B= Adjustment value for each paper size (B)

Important

Horizontal

alignment

plates

04-080 Fold&Staple Paper Width Adj.

04-090 Half-Fold Strength Adj.

3Fold and Fold & Staple Adjustment

Adjustment to use: [Tri-Fold Position Adjustment]

Adjust the 1st fold position in Multi Tri-Fold

mode.

This adjustment is only available in Multi Tri-Fold

mode.

Tri-Fold fold positions

1st fold (inside)

2nd fold (outside) Adjustment to use: [Tri-Fold Position Adjustment]

Positive direction (+):

Increases the 1st fold distance.

Negative direction (-):

Reduces the 1st fold distance.

1st fold distance

2nd fold distance

Positive direction (+):

Increases the 2nd fold distance.

Negative direction (-):

Reduces the 2nd fold distance.

(-)

(+)

(-)

Adjust the 2nd fold position in Multi Tri-Fold

mode.

This adjustment is only available in Multi Tri-Fold

mode.

Each adjustment value described on this page is obtained by adding A to B (A + B).

•A= Offset adjustment value for all sizes (A)

•B= Adjustment value for each paper size (B)

Important

04-100

Tri-Fold Position Adjustment

4Other Adjustments

Adjustment to use: [Horizontal Position Adj.(FD)]

Punch hole positions

Horizontal direction

Vertical direction

Skew

Adjustment to use: [Vertical Position Adj.(CD)]

Adjustment to use: [Registration Adjustment]

Adjust the punch hole positions in the paper feed

direction. Positive direction (+):

The punch hole positions are closer to

the edge of the paper.

Negative direction (-):

The punch hole positions are away

from the edge of the paper.

(+)

(-)

Adjust the punch hole positions in the crosswise

direction.

(+)

Positive direction (+):

Moves the punch hole positions

backward.

Negative direction (-):

Moves the punch hole positions

forward.

Paper feed

direction

Adjust the loop amount of the alignment operation

(resist) to straighten the paper, and correct the

angle of the punch holes.

Positive direction (+):

Secures the time until both edges of

the paper are straightened by

increasing the loop when the paper

is aligned. However, it may cause

wrinkles when thin paper is used.

Negative direction (-):

Reduces the loop when

paper is aligned.

Paper

feed

direction

Side view

(-)

(+)

(-)

Paper

alignment

roller

4-1. Punch Hole Adjustment Items

The punch function is available when the Punch Kit [PK-525] is mounted.

The adjustments described in this chapter are only available in Punch mode.

Paper feed direction

Each adjustment value described on this page is obtained by adding A to B (A + B).

•A= Offset adjustment value for all sizes (A)

•B= Adjustment value for each paper size (B)

Important

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios de impresora de Konica Minolta

Konica Minolta

Konica Minolta bizhub 223 Manual de usuario

Konica Minolta

Konica Minolta LU-204 Manual de usuario

Konica Minolta

Konica Minolta MK-735 Manual de usuario

Konica Minolta

Konica Minolta Image Controller IC-205 Manual de usuario

Konica Minolta

Konica Minolta LU-302 Manual de usuario

Konica Minolta

Konica Minolta MAGICOLOR 4600 Series Manual de usuario

Konica Minolta

Konica Minolta RU-513 Manual de usuario

Konica Minolta

Konica Minolta PK-517 Manual de usuario

Konica Minolta

Konica Minolta FOCUS Manual de usuario

Konica Minolta

Konica Minolta ViZion DR+ 1417V2 Manual de uso y cuidado

Konica Minolta

Konica Minolta FS-110 Manual de usuario

Konica Minolta

Konica Minolta DF-633 Manual de usuario

Konica Minolta

Konica Minolta AFR-12 Guía de configuración

Konica Minolta

Konica Minolta bizhub C650 Series Manual de usuario

Konica Minolta

Konica Minolta PI-506 Manual de usuario

Konica Minolta

Konica Minolta PC-410 Manual de usuario

Konica Minolta

Konica Minolta HD-524 Manual de usuario

Konica Minolta

Konica Minolta AU-201S Manual de usuario

Konica Minolta

Konica Minolta VI-506 Manual de usuario

Konica Minolta

Konica Minolta IT-101 Cómo utilizar

Konica Minolta

Konica Minolta PC-101 Manual de usuario

Konica Minolta

Konica Minolta Magicolor 5550 Instrucciones de funcionamiento y mantenimiento

Konica Minolta

Konica Minolta AD-509 Manual de usuario

Konica Minolta

Konica Minolta IP-011 Cómo utilizar

Manuales populares de Accesorios de impresora de otras marcas

Star Micronics

Star Micronics TSP800 Series Manual de usuario

REA

REA JET HR pro 2K Manual de usuario

HP Laserjet,Color Laserjet 4si Manual de usuario

oliser

oliser MS 45 Manual de usuario

Roland

Roland DU2-64 Instrucciones y recetas

Xerox

Xerox EFI EXP6000 Manual de usuario

Canon

Canon Finisher-T1 Manual de usuario

Sharp

Sharp FO-1MK Manual de usuario

Labelmate

Labelmate PM-300 Manual de usuario

Epson

Epson T6248 Manual de funcionamiento

Epson

Epson OT-BZ20 Manual de usuario

Canon

Canon TonerRobot EP-27 Manual de usuario

Ricoh

Ricoh LCIT RT5100 Guía de inicio rápido

GBC

GBC 16 Series Manual de usuario

Canon

Canon INNER 2-WAY TRAY-E1 Manual de operación y mantenimiento

Develop

Develop SD-509 Manual de usuario

Kyocera

Kyocera KM-6230 Manual

Triumph Adler

Triumph Adler DF-710 Manual