Konica Minolta PK-517 Manual de usuario
E-1
INSTALLATION MANUAL
A10E-9550-01
PK-517 Punch Kit
I. Accessory parts
Note:
This manual provides the illustrations of the acces-
sory parts and machine that may be slightly different
in shape from yours. In that case, instead of the
illustrations, use the appearance of your machine to
follow the installation procedure. This does not
cause any significant change or problem with the
procedure.
II. Installation procedures
Note:
When mounting the punch kit, mount it before
mounting the finisher to the machine.
1. Turn off the machine and unplug the power cord
from the power outlet.
2. Remove the protective tape.
3. If the finisher is mounted on the machine, remove
the finisher.
Note:
For the finisher removal procedure, see installa-
tion manual for finisher.
4. Remove the exit tray from the finisher.
No. Name Shape Q’ty
1. Punch unit
1
2. Punch box
1
3. Label
1
4. Installation
manual
1
set
After unpacking, be sure to get rid of the
packaging materials and keep them out of
the reach of children.
Putting the head in the plastic bag
involves danger of suffocation.
A10EIXC001DA
A10EIXC002DA
4512IXC053DA
4980IXC019DA
A10EIXC003DA
A10EIXC004DA
5. Remove the upper cover from the finisher (four
screws).
6. Remove the plate from the finisher as shown in
the illustration (two screws).
7. Remove the plate from the finisher as shown in
the illustration (three screws).
8. Open the cover of the finisher as shown in the
illustration and place the punch kit on the finisher.
9. Connect the punch kit connector to the finisher.
A10EIXC005DB
A10EIXC006DA
A10EIXC007DA
A10EIXC008DA
A10EIXC009DA
Applied Machine: FS-527
A10E-9550-01E.fm 1 ページ ２００９年７月２日 木曜日 午後６時２３分
E-2
10. Slightly raise the punch kit and insert the plate
removed in step 7 between the finisher and the
punch kit.
Note:
Align the three dowels on the finisher with the
three dowel holes on the plate.
11. Secure the plate to the finisher with the three
screws removed in step 7.
12. Align the middle mark on the punch kit with the
dowel on the plate and secure the punch kit (two
screws).
Note:
Use the screws removed in step 6.
13. Attach the upper cover removed in step 5 to the
finisher (four screws).
14. Attach the exit tray removed in step 4 to the fin-
isher.
15. Install the furnished punch box.
16. Affix the furnished label to the front door of the
finisher as shown in the illustration.
17. Mount the finisher to the machine.
Note:
For the finisher mounting procedures, see installa-
tion manual for finisher.
A10EIXC010DB
Dowel
A10EIXC011DA
A10EIXC012DA
A10EIXC013DA
A10EIXC014DA
III. Punch option setting
1. Plug the power cord into the power outlet and
turn on the machine.
2. Display the Service Mode screen. (For details of
how to display the Service Mode screen, see the
service manual.)
3. Touch “Finisher.”
4. Touch “Punch option setting.”
5. Touch “PK-517” and select a desired number of
holes.
6. Touch “decision.”
7. Touch “END.”
8. Touch “Exit” on the Service Mode screen.
IV. Punch hole deviance adjustment
1. Make a copy in the punch mode.
(Refer to the user’s guide (copy operations))
2. Fold the copy into halves and check for possible
deviation in the punch hole positions.
Specifications: 0 ± 2.0 mm
* If the positional deviation of the punch holes is
not within the accepted range, take the following
steps.
3. Open the upper cover of the finisher.
4. Loosen the two screws that hold the punch unit in
place.
5. Move the punch unit back and forth to adjust its
position, referring to the guide lines.
6. After the adjustment, tighten the two screws loos-
ened in step 4.
7. Close the upper cover of the finisher.
8. Make a copy and check the punch hole positions
again.
A10EIXC018DA
A10EIXC019DA
A10EIXC015DA
Screw
A10EIXC016DA
A10E-9550-01E.fm 2 ページ ２００９年７月２日 木曜日 午後６時２３分
E-3
V. Punch hole position adjustment
1. Make a copy in the punch mode.
(Refer to the user’s guide (copy operations))
2. Measure width A on the copy and check to see if
the measured dimension falls within the specified
range.
<North America: 2 holes, 3 holes>
Specifications: 9.5 ± 1.0 mm
<Europe: 4 holes>
Specifications: 11 ± 1.0 mm
<Sweden: 4 holes>
Specifications: 10.5 ± 1.0 mm
• If the measured width A outside the specified
range, perform the following procedure to punch
hole position adjustment.
3. Display the Service Mode screen.
(For details of how to display the Service Mode
screen, see the service manual.)
4. Touch “Finisher.”
5. Touch “FS-FN adjustment.”
6. Touch “Punch Horizontal Position.”
7. Set the correction value using the /
keys.
• To make width A wider, enter a positive value.
• To make width A narrower, enter a negative
value.
8. Touch “END.”
9. Touch “OK.”
10. Touch “Exit” on the Service Mode screen.
11. Make a copy and check the punch hole positions
again.
VI. Punch regist loop size adjustment
1. Make a copy in the punch mode.
(Refer to the user’s guide (copy operations))
2. Check the tilt of the output paper.
• If it tilts, follow the procedures below for punch
loop adjustment.
3. Display the Service Mode screen.
(For details of how to display the Service Mode
screen, see the service manual.)
4. Touch “Finisher.”
5. Touch “FS-FN adjustment.”
6. Touch “Punch Regist Loop Size.”
7. Set the correction value using the /
keys.
• To make loop length larger, enter a positive value.
• To make loop length smaller, enter a negative
value.
8. Touch “END.”
9. Touch “OK.”
10. Touch “Exit” on the Service Mode screen.
11. Make a copy again and check the deviance of
punch hole position.
4512IXE057DA
<North America:
2 holes>
<North America:
3 holes>
A
<Europe: 4 holes> <Sweden: 4 holes>
A
4512IXC056DA
AA
4512IXE062DA4512IXE061DA
A10E-9550-01E.fm 3 ページ ２００９年７月２日 木曜日 午後６時２３分
Otros manuales de Accesorios de impresora de Konica Minolta
Konica Minolta
Konica Minolta Pi3505e Manual de usuario
Konica Minolta
Konica Minolta ViZion DR+ 1417V2 Manual de uso y cuidado
Konica Minolta
Konica Minolta HT-509 Manual de usuario
Konica Minolta
Konica Minolta Magicolor 5550 Instrucciones de funcionamiento y mantenimiento
Konica Minolta
Konica Minolta JS-506 Manual de usuario
Konica Minolta
Konica Minolta MAGICOLOR 4600 Series Manual de usuario
Konica Minolta
Konica Minolta bizhub 223 Manual de usuario
Konica Minolta
Konica Minolta FS-532 Manual de usuario
Konica Minolta
Konica Minolta DF-633 Manual de usuario
Konica Minolta
Konica Minolta AFR-12 Guía de configuración
Konica Minolta
Konica Minolta MK-735 Manual de usuario
Konica Minolta
Konica Minolta HD-524 Manual de usuario
Konica Minolta
Konica Minolta PC-101 Manual de usuario
Konica Minolta
Konica Minolta PC-410 Manual de usuario
Konica Minolta
Konica Minolta LU-302 Manual de usuario
Konica Minolta
Konica Minolta bizhub C220 Series Manual de usuario
Konica Minolta
Konica Minolta LU-204 Manual de usuario
Konica Minolta
Konica Minolta HT-502 Manual de usuario
Konica Minolta
Konica Minolta Di1611 Manual de usuario
Konica Minolta
Konica Minolta DB-209 Cómo utilizar
