Konica Minolta MK-735 Manual de usuario
E-1
MK-735 Mount Kit
INSTALLATION MANUAL
A4NM-9550-04
Applied Machines: C554e/C454e/C364e/C284e/C224e/C554/C454/C364/C284/C224/C368/C308/C258/C287/
C227/554e/454e/364e/284e/224e/367/287/227
COLOR MFP: 55 ppm /45 ppm/36 ppm/30 ppm/28 ppm/25 ppm/22 ppm
MFP: 55 ppm/45 ppm/36 ppm/28 ppm/22 ppm
Product Code: A5AY/A5C0/A5C1/A5C2/A5C4/A2XK/A4FJ/A161/A4FK/A4FM/A7PU/A7PY/A7R0/A797/A798/A61D/
A61E/A61F/A61G/A61H/A789/A7AH/A7AK
1. Accessory parts
*1 This part is not used for installing the Authentica-
tion Unit AU-201S/AU-201.
*2 This part is not used in this installation.
No. Name Shape Q’ty
1. Authentication
unit holder
1
2. Authentication
unit clamp A
1
3. Authentication
unit clamp B*1
1
4. Authentication
unit clamp C*1
1
5. Extender cable*1
1
6. Authentication
label 1
7. Card holder
1
8. Screws A
2
9. Screws B*2
2
10. Cable clamp*2
1
11. Double-faced tape
A1
12. Double-faced tape
B1
13. Installation
manual 1
set
No. Name Shape Q’ty
Keep this bag away from babies and
children. Do not use in cribs, beds,
carriages, or playpens.
The thin film may cling to nose and
mouth and prevent breathing. This bag is
not a toy.
E-2
Note:
• This manual provides the illustrations of the
accessory parts and machine that may be
slightly different in shape from yours. In that
case, instead of the illustrations, use the
appearance of your machine to follow the
installation procedure. This does not cause any
significant change or problem with the proce-
dure.
<C554e/C454e/C364e/C284e/C224e/C554/C454/
C364/C284/C224/554e/454e/364e/284e/224e>
• The contents of this manual are for the unit with
the Authentication Unit installed AU-201S/AU-
201.
• To use this product, the Authentication Unit
AU-201S/AU-201 is required.
• For information on the procedure for attaching
the Authentication Unit AU-201S/AU-201 to the
Working table, see the installation manual of
Authentication Unit AU-201S/AU-201.
<C368/C308/C258>
• The contents of this manual are for the unit with
the Authentication Unit installed AU-201S.
• To use this product, the Authentication Unit
AU-201S is required.
• For information on the procedure for attaching
the Authentication Unit AU-201S to the Working
table, see the installation manual of Authentica-
tion Unit AU-201S.
<C287/C227/367/287/227>
• The contents of this manual are for the unit with
the Authentication Unit installed AU-201S.
• To use this product, the Authentication unit AU-
201S and the Local Interface Kit EK-609/EK-
608 are required.
• For information on the procedure for attaching
the Authentication unit AU-201S to the Working
table, see the installation manual of Authentica-
tion unit AU-201S.
• When mounting the Upgrade Kit UK-212 at the
same time, mount the Upgrade Kit UK-212 first.
2. Installation procedures
<Installations to models C554e/C454e/C364e/
C284e/C224e/C554/C454/C364/C284/C224/554e/
454e/364e/284e/224e>
(1) Turn OFF the power switch and unplug the
power cord from the power outlet.
(2) Attach the ferrite core supplied with the Authenti-
cation Unit AU-201S/AU-201 to the Authentica-
tion Unit AU-201S/AU-201 at the position shown
in the illustration.
Note:
• Place the ferrite core such that the cable is
wound twice around the ferrite core.
• Place the ferrite core approximately 60 mm
away from the authentication unit.
<Installations to models C554e/C454e/C364e/
C284e/C224e/C554/C454/C364/C284/C224/554e/
454e/364e/284e/224e>
Follow the installation procedures starting on page
E-2.
<Installations to models C368/C308/C258>
Follow the installation procedures starting on page
E-6.
<Installations to models C287/C227/367/287/227>
Follow the installation procedures starting on page
E-10.
E-3
(3)
<When the Working Table WT-506 is mounted to the
main body>
Refer to the installation manual for the Working
Table WT-506 and remove the working table.
(4) Remove the scanner right cover.
(Three screws).
(5) Open the right door of the main body.
(6) Remove the cover shown in the illustration from
the main body.
(One screw and one shoulder screw)
(7) Remove the control panel right cover.
(Two screws)
(8) Remove the control panel left cover.
(Two screws)
(9) Remove the cover shown in the illustration from
the main body. (One screw)
(10) Remove the four screws and two tabs of the
control panel front cover.
Cover
Tab
Tab
E-4
(11)
< C554e/C454e/C364e/C284e/C224e/554e/454e/
364e/284e/224e >
Remove the harness from the wire saddle.
Disconnect the two connectors, and remove the
control panel front cover.
< C554/C454/C364/C284/C224 >
Disconnect the connector, and remove the con-
trol panel front cover.
(12) Attach the authentication unit holder to the main
body. (One supplied screw A)
(13) Route the connector of the authentication unit
through the edge cover shown in the illustra-
tion.
(14) Attach the supplied double-faced tape A to the
authentication unit at the position shown in the
illustration and stick the unit to the holder.
(15) Attach the authentication unit clamp A.
(One supplied screw A)
Connector
Wire saddle
Connector
E-5
(16) Open the cover shown in the illustration on the
right side of the main body.
(17) Connect the USB cable to the main body.
Note:
Connect it to either of the two ports.
(18) Route the USB cable as shown in the illustra-
tion. Pull the USB cable up in order to remove
slack.
(19) Route the USB cable through the harness
guide and the two wire saddles shown in the
illustration.
(20) Route the USB cable as shown in the illustra-
tion. Route the cable through the seven wire
saddles and the edge cover of the main body.
(21) Close the cover that you opened in step (16).
(22) Place the rest of the USB cable in the space
between the authentication unit and the main
body frame.
(23) To install the covers, connector, and others
removed in steps (4) to (11), reverse the
removal procedure.
Port
Wire saddles
Wire saddle
Wire saddle
Edge cover
E-6
(24) Attach the authentication label to the cover at
the position shown in the illustration.
(25) Attach the supplied double-faced tape B to the
card holder at the position shown in the illustra-
tion. Attach the card holder to the main body at
the position shown in the illustration.
Note:
• Make sure that double-faced tape B does not
project from the edge of the card holder.
• When attaching the card holder to the main
body, make sure that the holder does not over-
lap the authentication label.
(26) Go to “3. Configuration procedures” on page
E-13.
<Installations to models C368/C308/C258>
(1) Turn OFF the power switch and unplug the
power cord from the power outlet.
(2) Attach the ferrite core supplied with the Authenti-
cation Unit AU-201S to the Authentication Unit
AU-201S at the position shown in the illustration.
Note:
• Place the ferrite core such that the cable is
wound twice around the ferrite core.
• Place the ferrite core approximately 60 mm
away from the authentication unit.
(3)
<When the Working Table WT-506 is mounted to the
main body>
Refer to the installation manual for the Working
Table WT-506 and remove the working table.
(4) Remove the scanner right cover.
(Three screws).
(5) Open the right door of the main body.
30 mm
65 mm
E-7
(6) Remove the cover shown in the illustration from
the main body.
(One screw and one shoulder screw)
(7) Remove the control panel right cover.
(Two screws)
(8) Remove the two caps from the control panel left
cover.
(9) Remove the five screws and two tabs and
remove the control panel front cover.
Note:
Do not use too much force to remove the cover as
the harness is connected.
(10) Disconnect the connector from the board on the
control panel front cover.
(11) Attach the authentication unit holder to the main
body. (One supplied screw A)
Tab
E-8
(12) Pass the authentication unit connector through
the opening shown in the illustration.
(13) Attach the supplied double-faced tape A to the
authentication unit at the position shown in the
illustration and stick the unit to the holder.
(14) Attach the authentication unit clamp A.
(One supplied screw A)
(15) Open the right rear cover of the main body and
remove the screw shown in the illustration.
(16) Release the tab and open the upper right rear
cover.
(17) Connect the USB cable to the main body.
Note:
Connect the port shown in the illustration.
Tab
E-9
(18) Route the USB cable as shown in the illustra-
tion. Pull the USB cable up in order to remove
slack.
(19) Route the USB cable through the harness
guide and the two wire saddles shown in the
illustration.
(20) Route the USB cable as shown in the illustra-
tion. Route the cable through the seven wire
saddles of the main body.
(21) Place the rest of the USB cable in the space
between the authentication unit and the main
body frame.
(22) Insert the tab and close the upper right rear
cover.
(23) Install the screw shown in the illustration and
close the right rear cover.
(24) To install the covers, connector, and others
removed in steps (3) to (10), reverse the
removal procedure.
Tab
E-10
(25) Attach the authentication label to the cover at
the position shown in the illustration.
(26) Attach the supplied double-faced tape B to the
card holder at the position shown in the illustra-
tion. Attach the card holder to the main body at
the position shown in the illustration.
Note:
• Make sure that double-faced tape B does not
project from the edge of the card holder.
• When attaching the card holder to the main
body, make sure that the holder does not over-
lap the authentication label.
(27) Go to “3. Configuration procedures” on page
E-13.
<Installations to models C287/C227/367/287/227>
(1) Turn OFF the power switch and unplug the
power cord from the power outlet.
(2) Attach the ferrite core supplied with the Authenti-
cation Unit AU-201S to the Authentication Unit
AU-201S at the position shown in the illustration.
Note:
• Place the ferrite core such that the cable is
wound twice around the ferrite core.
• Place the ferrite core approximately 60 mm
away from the authentication unit.
(3)
<When the optional Keypad KP-101 is mounted>
Remove the two screws and remove the cover
on the back side of the keypad. Disconnect the
connector and remove the keypad.
30 mm
65 mm
Tabla de contenidos
Otros manuales de Accesorios de impresora de Konica Minolta
Konica Minolta
Konica Minolta bizhub 223 Manual de usuario
Konica Minolta
Konica Minolta FOCUS Manual de usuario
Konica Minolta
Konica Minolta IT-101 Cómo utilizar
Konica Minolta
Konica Minolta Image Controller IC-205 Manual de usuario
Konica Minolta
Konica Minolta DB-209 Cómo utilizar
Konica Minolta
Konica Minolta WT-513 Manual de usuario
Konica Minolta
Konica Minolta DK-510 Manual de usuario
Konica Minolta
Konica Minolta PC-101 Manual de usuario
Konica Minolta
Konica Minolta LU-204 Manual de usuario
Konica Minolta
Konica Minolta FS-110 Manual de usuario
Konica Minolta
Konica Minolta Magicolor 5550 Instrucciones de funcionamiento y mantenimiento
Konica Minolta
Konica Minolta bizhub 361 Manual de usuario
Konica Minolta
Konica Minolta PI-506 Manual de usuario
Konica Minolta
Konica Minolta JS-506 Manual de usuario
Konica Minolta
Konica Minolta bizhub C220 Series Manual de usuario
Konica Minolta
Konica Minolta PK-511 Manual de usuario
Konica Minolta
Konica Minolta AU-201S Manual de usuario
Konica Minolta
Konica Minolta HD-524 Manual de usuario
Konica Minolta
Konica Minolta MAGICOLOR 4600 Series Manual de usuario
Konica Minolta
Konica Minolta PI-505 Manual de usuario
