PROAIM Victor Pro Manual de usuario
1
Please inspect the contents of your shipped package to ensure you have received everything that is listed
below.
Victor Pro Video Producon Camera Cart (CT-VCTR-PRO-48)
Assembly Manua l
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any means,
electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permied by the applicable copyright
statutes or in wring by the Publisher.
What’s In The Box
Lower Shelf
2 x Crossbars
2 x Hinge Handle
Allen key L– Type, 4 x Screws
Top Shelf
Carrying Handle
4 x Knobs
2
2 x Pneumac Tires Without
Break With Packing Pouch
2 x Pneumac Tires With
Break With Packing Pouch
Victor Pro Camera Cart Setup
• Open all the 4 locks which are on both sides
end of the cart.
• Unlock the re (With brake) by ipping the
knob.
4 x (31” Length) Rods With Packing
• Aer unlocking all locks, separate the upper
and lower shelf.
• Pull and ip the locking pin in upward direc-
on to open the locks.
NOTE: Two peoples are needed to assemble the cart.
Pneumac Tires With break
3
• The cart would look like this aer aaching
both the res (With break).
NOTE: To keep the cart in stac posion, lock
the wheels by pushing down the lever.
• Aach the unlocked re (With break) on
lower shelf’s dovetail bracket by sliding on it
as shown in the image.
• Flip the knobs to secure the aached re As
shown in image.
• Unlock the re (non break) by ipping the
knob.
• Aach the unlocked res (non break) on
lower shelf’s dovetail bracket by sliding as
shown in the image.
Pneumac Tires Without Break
• The cart would look like this aer aaching
both the res (non break).
4
• Tighten all the knobs provided at each corner
of the lower cart. So that all the rods are
properly aached to the cart as shown in the
image.
• Loosen the screw of the carrying handle with
the help of Allen key L-type as shown in im-
age.
• Now place the carrying handle on the side of
the boom shelf.
• Follow the same steps for all screw removal
before aaching it to lower shelf.
• Loose all the 4 knobs of lower shelf’s corner
hole and insert rod into it, as shown in image.
• Now, screw the carrying handle to lower shelf
with the help of allen key L-Type.
Rod
Carrying Handle
5
• Tighten all the 4 corner knobs of upper shelf
so that upper shelf doesn't fall down.
• Tighten knobs ghtly to set crossbar properly
on the rods.
• Now place the clamps of crossbar on rods, as
shown in image.
• Loosen the knob to open clamp of the cross-
bar.
• Now mount the upper shelf on the top of
the rods by aligning it in the corners.
• Follow same steps for all screws to check
whether they are properly set.
Upper Shelf
Crossbar
6
• Place handle clamp on the rod and adjust the
hinge handle accordingly.
• Follow same steps to aach second hinge
handle.
NOTE: It helps create the leverage needed while
liing the cart quickly over obstacles, stairs or
other incline surfaces.
• Follow the same step with second knob and
open the ap.
• Loosen the handle to open clamp of hinge
handle.
• Unlatch upper shelf’s ap by sliding the knob.
• The crossbar would look like this aer
aaching both clamps, as shown in image.
Hinge Handle
7
• The cart would look like this aer following all
the steps correctly.
Warranty: We oer one year warranty for our products from date of purchase. Within this period of me,
we will repair it without charge for labor or parts. Warranty doesn’t cover transportaon costs nor does it
cover a product subjected to misuse or accidental damage. Warranty repairs are subjected to inspecon and
evaluaon by us.
Liability: We are not liable for damage caused by products that we do not supply or from mishandling in
transit, accident, misuse, neglect, lack of care of the product, or service by anyone other than our company.
Contact Us: In case of any kind of dissasfacon, please Contact us immediately and we promise our utmost
support and care unl you use our product.
YOUR PROAIM VICTOR PRO VIDEO PRODUCTION CAMERA CART
ALL DRESSED UP AND READY TO GO!
(SHOWN WITH OPTIONAL ACCESSORIES)
Este manual sirve para los siguientes modelos
4
Tabla de contenidos
Otros manuales de Accesorios para cámaras de PROAIM
PROAIM
PROAIM 14ft. Jib Arm with Jib Stand Manual de usuario
PROAIM
PROAIM SL-161 Manual de usuario
PROAIM
PROAIM P-L2-SL Manual de usuario
PROAIM
PROAIM CST-100-01 Manual de usuario
PROAIM
PROAIM Cambird Pro SL-CBPR-01 Manual de usuario
PROAIM
PROAIM Spinhawk Professional Manual de usuario
PROAIM
PROAIM QR-WV-710 Manual de usuario
PROAIM
PROAIM Fusion Manual de usuario
PROAIM
PROAIM Flylite Jr. FLT-JR Manual de usuario
PROAIM
PROAIM P-OHCP-01 Manual de usuario
PROAIM
PROAIM CINEMA Series Manual de usuario
PROAIM
PROAIM RS274 Manual de usuario
PROAIM
PROAIM P-BPDP-19 Manual de usuario
PROAIM
PROAIM DL-FLDB-01 Manual de usuario
PROAIM
PROAIM P-W5P24-BASE Manual de usuario
PROAIM
PROAIM Explorer Manual de usuario
PROAIM
PROAIM CAMTREE HUNT Manual de usuario
PROAIM
PROAIM CINEMA Series Manual de usuario
PROAIM
PROAIM SnapRig CG210 Manual de usuario
PROAIM
PROAIM P-WV-2PL-SD Manual de usuario
