PROAIM JB-CMTM-01 Manual de usuario
1
Please inspect the contents of your shipped package to ensure you have received everything that is listed
below.
Comet Mini 4.5 Euro/Elemac Camera Jib (JB-CMTM-01)
Assembly Manua l
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any means,
electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permied by the applicable copyright
statutes or in wring by the Publisher.
What’s In The Box
Proaim 2.5 Comet Mini Jib
1 x 2 Extension Arm
2 x Counter weight Rods
1 x Extension rod
Flight Case
2
Comet Mini Jib Setup
• Place the euro adapter plate (Not Included)
to the center hole of the Spin Dolly
(Not Included).
• Aach the euro adapter plate (Not Included)
to the Spin Dolly (Not Included) with the help
of the bolt and then ghten it using the Allen
key.
• Aer mounng the Flexino Bazooka
(Not Included), secure it by properly
ghtening the ratchet knob.
• Loosen the ratchet knob of the Flexino
Bazooka (Not Included) and mount it on the
euro adapter (Not Included) placed on the
Spin Dolly (Not Included).
• Similarly, ghten all the other bolts to rmly
secure the euro plate adapter (Not Included).
• Place the Comet Jib onto the euro adapter of
center column.
3
• Fix the jib fork with the center column by
locking the knob via locking lever.
• Comet Jib is properly aached.
• Re-Insert the side knob to lock it.
• Loosen the knob located at one of ends of the
jib, & pull out the telescopic secon, as
shown in the image.
• Then pull & take out the side knob of the jib.
• Unlock the rod pin, Then insert the
counterweight rod through the hole.
4
• Then add weights (Not Included) on both the
rods accordingly and secure them with the
locking pins.
2 dierent length rods of counterweight for easy balancing
Dynamic Moves For Your Camera Varied Tilng Range for Varied Lengths
NOTE: It comes with two counterweight rods that let you hang dumbbell weights for
counterbalancing.
5
• The Comet jib provides 360° rotaon with its
panning knob.
• Loosen and remove the adapter knob present
on the front of the Comet jib.
• Aer mounng the uid head, aach the
castle ring to the boom of the uid head.
• Now, properly secure the oset bracket
(Not Included) by ghtening the ratchet knob
and adapter knob.
• Loosen the ratchet knob of the oset bracket
(Not Included) and mount it on the front
secon adapter of the jib.
Mounng of Fluid Head
• Loosen the Castle Ring of the Fluid Head
(Not Included) and mount it on the Oset
Bracket.
360°
panning
6
Extend the length of Comet Jib
• Push the knob present on the front secon of
the comet jib and properly remove it.
• Aach the Camera Plate to the Camera
(Not Included) by matching the threads and
properly secure with the help of a screwdriver
(Not Included).
• Now, secure it with the castle nut.
• Push the buon of the Fluid Head
(Not Included) and remove the Camera Plate.
NOTE: The Comet can be combined with
addional Proaim accessories, Suitable for all
standard Euro / Mitchell Remote Head systems.
• Slide the Camera onto the Fluid Head and
properly lock it with the help of the locking
pin.
7
• Now ,securely re-insert the push pin.
• Firmly secure the ratchet knob by ghtening
it, as shown in the image.
• Now, loosen the ratchet knob present on this
knob.
• Remove the pushpin present on the top rod
of the front secon by pushing it.
• Loosen and remove the ratchet knob present
on the back side of the Jib.
• You can set the required height by removing
the push pin present on the top most rod of
the Comet Jib.
Extend the length of Comet Jib
8
• The extension arm is successfully aached to
the Comet Jib.
• Now, re-insert and ghten the ratchet knob.
• Properly remove the extension arm by loos-
ening it.
• Insert the extension arm into the Comet Jib.
• Now, detach the front secon of the jib ,as
shown in the image.
Assembly of Extension Arm
9
• Carefully align the extension rod with the rod
of the Comet Jib and aach it.
• Insert the head secon of the Comet Jib on
the extension arm.
• Now, insert the rod of the head secon into
the hole of the extension rod.
• Then, ghten the ratchet knob of the Jib.
• Aer inserng the rod, secure it with the help
of the pushpin.
• Now, insert the push pin to secure the rod.
Assembly of Extension rod
10
• Loosen the ratchet knob of the head secon
of the Jib.
• Now, properly ghten the ratchet knob of the
head secon to secure it in its place.
• Loosen the adapter knob present on the head
secon with the help of Allen key.
• Remove and aach the safety cap of the
boom rig (Not Included) to the head secon
of the Jib.
• Now, remove the adapter with ease.
Assembly of Boom Rig
Otros manuales de Accesorios para cámaras de PROAIM
PROAIM
PROAIM JB-FLMS-01 Manual de usuario
PROAIM
PROAIM SnapRig CG210 Manual de usuario
PROAIM
PROAIM CINEMA VCTR-TH Manual de usuario
PROAIM
PROAIM CINEMA Series Manual de usuario
PROAIM
PROAIM P-W5P24-BASE Manual de usuario
PROAIM
PROAIM CINEMA Series Manual de usuario
PROAIM
PROAIM P-18-JS Manual de usuario
PROAIM
PROAIM CINEMA Series Manual de usuario
PROAIM
PROAIM LB230 Manual de usuario
PROAIM
PROAIM CINEMA Series Manual de usuario
PROAIM
PROAIM SnapRig Cage CG215 Manual de usuario
PROAIM
PROAIM P-LLBT-MTCL Manual de usuario
PROAIM
PROAIM CINEMA Series Manual de usuario
PROAIM
PROAIM P-PRT-D Manual de usuario
PROAIM
PROAIM SR-016-00 Manual de usuario
PROAIM
PROAIM Power Pack Manual de usuario
PROAIM
PROAIM TRK-16-25 Manual de usuario
PROAIM
PROAIM P-GBD-01 Manual de usuario
PROAIM
PROAIM PT-SPN Manual de usuario
PROAIM
PROAIM Airwave XL Shock Manual de usuario
