Car-Interface V.LiNK CI-VL2-PC-HSD Manual de usuario

Version 07.09.2017

v.LiNK Video-inserter and navigation

CI-VL2-PC-HSD and CI-NAL-PC-HSD

Compatible with Citroen and Peugeot vehicles

with SMEG or SMEG+ navigation

with 4pin HSD LVDS connector on the monitor

VL2-PC-HSD: Video-inserter with 2 video + RGB + rear-view camera input and

CAN control

NAL-PC-HSD: Video-inserter with integrated navigation +2 video + rear-view

camera input and CAN control

Product features

Video-inserter for factory-infotainment monitors

2 CVBS video-inputs for after-market devices (e.g. DVD-Player, DVB-T tuner, …)

Built-in audio-switch (no audio-insertion)

Rear-view camera CVBS video-input

Automatic switching to rear-view camera input on engagement of reverse gear

Activatable parking guide lines for rear-view camera (not for all vehicles)

RGB-input for after-market navigation (VL2 only)

Video-in-motion (ONLY for connected video-sources)

Compatible with factory rear-view camera

AV-inputs PAL/NTSC compatible

Version 07.09.2017 CI-VL2-PC-HSD / CI-NAL-PC-HSD

Seite2

Contents

1. Prior to installation

1.1. Delivery contents

1.2. Checking the compatibility of vehicle and accessories

1.3. Boxes and connectors

1.3.1. CAN-bus box

1.3.2. Video-interface

1.3.2.1. Dip-switch settings

1.3.2.2. Enabling the interface’s video inputs (dip 1-3)

1.3.2.3. RGB-video input signal selection for after-market navigation (Dip 4)

1.3.2.4. Rear-view camera setting (dip 5)

1.3.2.5. Monitor selection (dip 7-8)

2. Installation

2.1. Place of installation

2.2. Connection schema

2.3. Connecting video-interface and CAN-box

2.4. Connection to the factory monitor

2.5. Connection to the head-unit

2.6. Connecting peripheral devices

2.6.1. After market RBG navigation (only VL2)

2.6.2. Video-sources to AV1 and AV2

2.6.3. Audio-switch and audio-insertion

2.6.4. After-market rear-view camera

2.6.4.1. Case 1: CAN-box detects reverse gear

2.6.4.2. Case 2: CAN-box does not detect reverse gear

2.6.4.3. Video signal connection

2.7. Connecting video-interface and keypad

2.8. Picture settings and guide lines

2.9. Connecting internal navigation (only NAL)

3. Interface operation

3.1. By LIST-key

3.2. By keypad

4. Specifications video-interface

5. Frequently asked questions

Appendix A –Internal Navigation (only NAL)

Version 07.09.2017 CI-VL2-PC-HSD / CI-NAL-PC-HSD

Seite3

Legal Information

By law, watching moving pictures while driving is prohibited, the driver must not be

distracted. We do not accept any liability for material damage or personal injury resulting,

directly or indirectly, from installation or operation of this product. This product should only

be used while standing or to display fixed menus or rear-view-camera video when the

vehicle is moving, for example the MP3 menu for DVD upgrades.

Changes/updates of the vehicle’s software can cause malfunctions of the interface. If

available, we offer free software-updates for our interfaces for one year after purchase. To

receive a free update, the interface must be sent in at own cost. Labor cost for and other

expenses involved with the software-updates will not be refunded.

1. Prior to installation

Read the manual prior to installation.

Technical knowledge is necessary for installation. The place of installation must be free of

moisture and away from heat sources.

1.1. Delivery contents

Take down the serial number of the interface and store this manual for support

purposes: ____________________

Version 07.09.2017 CI-VL2-PC-HSD / CI-NAL-PC-HSD

Seite4

Requirements

Vehicle Citroen and Peugeot

Head-unit/monitor Citroen SMEG+, Peugeot SMEG and SMEG+

with 4pin HSD LVDS connector on the monitor

Limitations

Video only The interface inserts ONLY video signals into the infotainment.

For audio insertion a factory audio-AUX input or FM-modulator

is required.

Factory rear-view camera Automatic switch-back from inserted video to factory rear-view

camera only while reverse gear is engaged. To extend the switch-

back additional electronics is required.

1.2. Checking the compatibility of vehicle and accessories

1.3. Boxes and connectors

1.3.1. CAN-bus box

The CAN-bus box reads digital signals from the CAN-bus and converts them for the video-

interface.

Version 07.09.2017 CI-VL2-PC-HSD / CI-NAL-PC-HSD

Seite5

1.3.2. Video-interface

The video-interface converts the connected after-market sources video signals to an LVDS

signal which is the inserted into the factory monitor on certain trigger options.

1.3.2.1. Dip-switch settings

Some settings must be selected by the dip-switches on the

video interface. Dip position down is ON and position up is OFF.

See following chapters for detailed information.

Dip

Function

ON (down)

OFF (up)

RGB-input

enabled

disabled

CVBS AV1-input

enabled

disabled

CVBS AV2-input

enabled

disabled

RGB-input resolution

800x480

400x240 or 480x240

Rear-view cam type

after-market

factory or none

No function

set OFF

No function

Set OFF

Version 07.09.2017 CI-VL2-PC-HSD / CI-NAL-PC-HSD

Seite6

1.3.2.2. Enabling the interface’s video inputs (dip 1-3)

Only the enabled video inputs can be accessed when switching through the interface’s video

sources. It is recommended to enable only the required inputs for the disabled will be

skipped when switching through the video interfaces inputs.

1.3.2.3. RGB-video input signal selection for after-market navigation (Dip 4)

If after-market RGB navigation or other RGB video source is connected, the source’s RGB

output signal must match the interface’s RGB video input setting.

1.3.2.4. Rear-view camera setting (dip 5)

If set to OFF, the interface switches to factory LVDS picture while the reverse gear is engaged

to display factory rear-view camera or factory optical park system picture.

If set to ON, the interface witches to its rear-view camera input CAM while the reverse gear

is engaged.

1.3.2.5. Monitor selection (dip 7-8)

Dips are not used.

2. Installation

Switch off ignition and disconnect the vehicle’s battery! The interface needs a permanent

12V source. If according to factory rules disconnecting the battery is to be avoided, it is

usually sufficient to put the vehicle is sleep-mode. In case the sleep-mode does not show

success, disconnect the battery with a resistor lead.

If power source is not taken directly from the battery, the connection has to be checked

for being start-up proven and permanent.

2.1. Place of installation

The interface is installed on the backside of the factory monitor and on the backside of the

head-unit.

Version 07.09.2017 CI-VL2-PC-HSD / CI-NAL-PC-HSD

Seite7

2.2. Connection scheme

Version 07.09.2017 CI-VL2-PC-HSD / CI-NAL-PC-HSD

Seite8

2.3. Connecting video-interface and CAN-box

The CAN-bus box reads digital signals from the CAN-bus and converts them for the video-

interface. ACC +12V max. 0.5A (red of 6pin) and reverse gear +12V max. 0.5A (green of 6pin)

constant signal. Video-source switching (white of 6pin) as +12V impulse.

Connect black female 10pin Micro-Fit connector of the Quadlock harness to the male

10pin Micro-Fit connector of the CAN-box.

Note: Check LEDs on CAN-box after reconnecting the battery, two must be on.

Connect white female 6pin Molex connector of the 6+2pin to 8pin cable to the male

6pin Molex connector of the video-interface.

Connect black female 8pin Micro-Fit connector of the 6+2pin to 8pin cable to male

8pin Micro-Fit connector of the CAN-box.

Note: Check LEDs on video-interface after reconnecting the battery, one must be on.

Note: The CAN-box is not compatible with all vehicles. If the CAN-box does not deliver ACC

to pin2 of the video-interface or blocks the vehicle CAN, it is possible to install without CAN-

box. In this case see also note in chapter after-market rear-view camera if one is supposed to

be connected.

Version 07.09.2017 CI-VL2-PC-HSD / CI-NAL-PC-HSD

Seite9

2.4. Connections to the factory monitor

Remove factory monitor.

Connect female 8pin Micro-Fit connector of the 4pin HSD LVDS cable to male 8pin

Micro-Fit connector of the video-interface.

Remove female 4pin HSD LVDS connector from the rear of the factory monitor and

connect it to the male 4pin HSD LVDS connector of the 4pin HSD LVDS cable.

Connect female 4pin connector of the 4pin HSD LVDS cable to the male 4pin HSD

LVDS connector of the factory monitor.

Version 07.09.2017 CI-VL2-PC-HSD / CI-NAL-PC-HSD

Seite10

2.5. Connections to the head-unit

Remove head-unit.

Remove the female Quadlock connector of the vehicle harness from the rear of the

navigation computer.

Connect female Quadlock connector of vehicle harness to the male Quadlock

connector of Quadlock harness.

Connect female Quadlock connector of Quadlock harness to the male Quadlock

connector of the head-unit.

2.6. Connecting peripheral devices

It is possible to connect an after-market RGB navigation (or other RGB video source, only

VL2), 2 after-market AV-sources and an after-market rear-view camera to the video-

interface.

Before final installation of the peripheral devices, we recommend a test-run of the

interface. Due to changes in the production of the vehicle manufacturer is always the

possibility of incompatibility.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios para automóviles de Car-Interface

Car-Interface

Car-Interface CI-RL-PCM3-TF Manual de usuario

Car-Interface

Car-Interface CI-C1-RNSE Manual de usuario

Car-Interface

Car-Interface RL4-MM-NP Manual de usuario

Car-Interface

Car-Interface CI-VL2-MIB-3 Manual de usuario

Car-Interface

Car-Interface CI-RL2-MTC Manual de usuario

Car-Interface

Car-Interface TV-Free CI-TF-C25 Manual de usuario

Car-Interface

Car-Interface RL4-NAC08 Manual de usuario

Car-Interface

Car-Interface CI-RL3-MIB-TT Manual de usuario

Car-Interface

Car-Interface CI-CARPLAY-NTG5 Manual de usuario

Car-Interface

Car-Interface CI-VL3-MBN51 Manual de usuario

Car-Interface

Car-Interface CI-RL4-UCON8-CP Manual de usuario

Car-Interface

Car-Interface CI-V5-CIC-F-PNP Manual de usuario

Car-Interface

Car-Interface CI-VL2-124SPY Manual de usuario

Car-Interface

Car-Interface CI-AUX-110 Manual de usuario

Car-Interface

Car-Interface v.LINK VL2-MIB-3 Manual de usuario

Car-Interface

Car-Interface CI-RL4-R40-E Manual de usuario

Car-Interface

Car-Interface CI-C2-MK-AUX Manual de usuario

Car-Interface

Car-Interface TV-Free CI-TF-UCON22 Manual de usuario

Car-Interface

Car-Interface CI-RL3-LR17 Manual de usuario

Car-Interface

Car-Interface CI-RL4-MM-NP Manual de usuario

Car-Interface

Car-Interface CI-CARPLAY-CIC Manual de usuario

Car-Interface

Car-Interface CI-UCON5-JEEP Manual de usuario

Car-Interface

Car-Interface c.LOGiC lite CI-C1-CCC Manual de usuario

Car-Interface

Car-Interface v.LOGiC CI-V5-CCC-PNP Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario

Car-Interface v.LiNK CI-VL2-PC-HSD Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas