Car-Interface C.LOGiC lite CI-C1-CCC Manual de usuario

Version 20.09.2017 CI-C1-CXC-TV1

c.LOGiC lite interfaces

CI-C1-CCC

CI-C1-CIC/CI-C1-CXC-TV1

CI-C1-E65/CI-C1-E65-TV

Compatible with

BMW Professional navigation systems

with iDrive and 6.5”/8.8” monitor

Interface-set AV and reverse camera input

with device control and video-in-motion

Version 20.09.2017 CI-C1-CXC-TV1

Page 1

Contents

1. Prior to Installation

1.1. Delivery contents

1.2. Check compatibility of vehicle and accessories

1.3. Check dip switch settings of the CAN-box

2. Installation

2.1. Installation 1series (E87), 3series (E90/E91/E92), 6series (E63/E64), X5(E70),

X6(E71) at example 5series (E60/E61)

2.1.1. Vehicles 5series w/o TV-tuner port

2.1.2. Vehicles 5series with TV-tuner port (factory TV-tuner uninstalled)

2.2. Installation 7series (E65/E66)

2.2.1. Vehicles 7series w/o TV-tuner port

2.2.2. Vehicles 7series with TV-tuner port (factory TV-tuner uninstalled)

3. Connections

3.1. Vehicles with factory rear-view camera

3.2. Vehicles with factory rear-view camera and factory-TV-tuner

3.3. Connecting an after-market rear-view camera

3.4. Special case –vehicles without fibre optical components (very rare)

4. Device control

4.1. Installation of IR-sensor additionally

5. Operation

5.1. Activation of the video-in-motion function

5.2. Selecting the interface as current AV-source

5.3. Assigning device control

5.4. Using device control

5.5. Button assignment table iDrive

6. Specifications

Appendix A –Device control table

Information

Changes of the vehicle software can cause malfunctions of the interface. We offer free

software-updates for interfaces for one year after purchase. To receive a free update, the

interface must be sent in at own cost. Labor cost for and other expenses involved with the

software-updates will not be refunded.

Version 20.09.2017 CI-C1-CXC-TV1

Page 2

1. Prior to installation

Read the manual prior to installation.

Technical knowledge is necessary for installation. The place of installation must be free of

moisture and away from heat sources.

1.1. Delivery contents

The necessary components for installation vary depending on the vehicle and accessories.

See below table to determine the parts necessary for installation. Product codes of the full

set are in bold letters (C1-xxx) while the set components (C1C-xxx) are listed below the set.

Options/

Navi Professional version

w/o factory TV-

tuner port

with factory

TV-tuner port

CCC Navigation (older iDrive, 1-2 buttons)

1series (E87), 3series (E90/91/92), 5series

(E60/61), 6series (E63/E64), X5 (E70), X6 (E71)

Vehicles from 2009 need additionally

harness TV-2X12P!

C1-CCC

C1C-M36

C1C-BM02

TV-436

TV-BM01

C1-CXC-TV1

C1C-M36

C1C-BM01

TV-436

TV-BM01

CIC Navigation (newer iDrive, 8 buttons)

3series (E90/91/92), 5series (E60/61), 6series

(E63/E64), X5 (E70), X6 (E71)

C1-CIC

C1C-M36

C1C-BM03

TV-436

TV-BM01

C1-CXC-TV1

C1C-M36

C1C-BM01

TV-436

TV-BM01

E65 Navigation

7series (E65/E66)

C1-E65

C1C-M36

C1C-BM02

TV-436

TV-BM65

C1-E65-TV

C1C-M36

C1C-BM01

TV-436

TV-BM65

If remote function of the interface should be used, additional IR-remote cables and

Y-adapters are needed, see chapter 4. Device control .

C1C-M36 HW_____ SW_____

C1C-BM01

TV-436 HW_____ SW_____

TV-BM65

C1C-BM02

C1C-BM03

TV-BM01

Take down the SW-version and HW-version of the interface boxes, cross the delivery

contents and store this manual for support purposes.

Version 20.09.2017 CI-C1-CXC-TV1

Page 3

1.2. Check compatibility of vehicle and accessories

1.3. Checking the DIP switches on the CAN-box

2. Installation

Switch off ignition and disconnect the vehicle from the battery!

The interface needs a permanent 12V source. If power source is not taken directly from

battery, the connection has to be checked for being start-up proven and stable.

Complete and correct function of the interface is possible only when, CAN and fibre optical

connections are made properly. Vehicles without TV icon will be programmed automatically

after installation of the interface.

Note: The loose white and green cable of harness TV-BM01/TV-BM65 are not required and

must be isolated.

Requirements

Vehicle 1series (E87) only CCC, 3series (E90/91/92), 5series (E60/61),

6series (E63/64), 7series (E65/66), X5 (E70), X6 (E71), Z4 (E89)

Navigation navigation system Professional CCC, E65 or CIC

with 6.5” or 8.8” monitor

Limitations

factory-TV-tuner has to be removed if installed

After-market rear-view cam Automatic switching to camera only from c.LOGiC mode.

factory-RSE (E65) need additional interface, VL-RGB02-C

Factory PDC If an after-market rear-view camera should be connected by the

c.LOGiC the visual PDC display must be deactivated occasionally

or permanently for camera picture.

Vehicles with CIC Dip 1 ON, Dip 2 OFF, Dip 3 OFF

Vehicles with CCC or E65 Dip 1 OFF, Dip 2 OFF, Dip 3 OFF

Version 20.09.2017 CI-C1-CXC-TV1

Page 4

2.1. Installation 1series (E87), 3series (E90/E91/E92), 6series (E63/E64), X5(E70), X6(E71)

at example 5series (E60/E61)

Needed parts

1. fibre optical interface C1C-M36

2. CAN interface TV-436

3. CAN interface harness TV-BM01

Version 20.09.2017 CI-C1-CXC-TV1

Page 5

2.1.1. Installation 5series w/o TV-tuner port

optical interface-harness C1C-BM02 for CCC-Navigation or C1C-BM03 for CIC-Navigation

is needed

Remove trim strip and step by step using a

plastic wedge. Do not proceed to quickly to

avoid breaking clamps of the trim strip.

Next remove screws 1 and 2 (see picture)

Remove climate control panel. Remove

CD/DVD drive trim. Trim is fixed by 2 screws

on the upper side and plugged to the

lower trim. Remove the lower trim

(plugged too).

Remove 4 screws and take out

navigation computer.

Version 20.09.2017 CI-C1-CXC-TV1

Page 6

Disconnect Quadlock connector from the back of the navigation computer.

The Quadlock connector includes different chambers. If present, remove the white, black

and the optical inserts, from the vehicle harness’ Quadlock connector. Plug the vehicle

harness’ Quadlock connector into the male Quadlock connector of the CAN interface harness

TV-BM01

Version 20.09.2017 CI-C1-CXC-TV1

Page 7

In the female Quadlock connector there is two compartments for inserts. Plug white insert

of the interface harness C1C-BMW0X into compartment for “Einsatz 1”.

If white insert in vehicle harness is present, remove video wires from white insert of fibre

optical interface harness and connect them to relating chambers in white vehicle harness’

insert.

On CCC navigation (C1C-BM02):

White insert („Einsatz 1“): video-signal (red) = PIN 4; signal-ground (black) = PIN 2

On CIC navigation (C1C-BM03):

White insert („Einsatz 1“): video-signal (red) = PIN 2; signal-ground (black) = PIN 12

On vehicles with factory rear-view camera, PIN 2 and PIN 12 are already occupied. In this

case connect according to 3.1. Vehicles with factory rear-view camera .

If no white insert in vehicle harness is present, connect white insert of fibre optical interface-

harness C1C-BM03 with Quadlock connector of the vehicle harness.

Remove optical insert from car side Quadlock connector.

Connect optical insert as shown in chapter 3. Connections with Quadlock

connector from CAN interface harness TV-BM01.

Connect the Quadlock connector from CAN interface harness TV-BM01 to the male Quadlock

plug of the navigation computer. Connect vehicle Quadlock connector with male Quadlock

plug of CAN interface harness TV-BM01.

Installation 5series with CIC w/o TV-port continue with chapter 4. Device control .

Version 20.09.2017 CI-C1-CXC-TV1

Page 8

2.1.2. Installation 5series with TV-tuner port (factory TV-tuner removed)

optical interface harness C1C-BM01 is needed

Installation of CAN interface analogue to

chapter 2.1.1. Installation 5series w/o TV-port .

Transfer white (if present), black and optical inserts from vehicle Quadlock connector to the

Quadlock connector of the CAN interface harness TV-BM01. Connect the CAN interface

harness Quadlock connector to the male Quadlock plug of the navigation computer and the

vehicle harness Quadlock connector to the male Quadlock plug of the CAN interface harness.

The blue factory-TV-tuner port is in found in

the trunk. Remove fibre optics from the blue

TV-port connector. Connect with black

connector of fibre optical interface harness

C1C-BM01. Obey the direction arrows

on the connector, see

chapter 3. Connections .

Connect black connector to fibre optical

interface. Connect blue plug to relating

counterpart of C1C-BM01 harness.

Factory rear-view cameras if present are connected to the factory TV-tuner.

Obey 3.2. Vehicles with factory rear-view camera and factory TV-tuner .

Installation 5series with TV-tuner port continue chapter 4. Device control .

2.2. Installation 7series (E65/E66)

Needed parts

1. fibre optical interface C1C-M36

2. CAN interface TV-436

3. CAN interface harness TV-BM65

Version 20.09.2017 CI-C1-CXC-TV1

Page 9

Board monitor removal

The CAN interface is connected to

the backside of the OEM screen.

Remove 3 TORX screws at the OEM screen.

Remove cover grill (only plugged). Place soft

towel beneath the board monitor

to avoid scratches

Flip down the board monitor. NOTE: The OEM

screen gets stuck with its connector at the upper

side of the cockpit. Insert a hard plastic sheet like

a credit card to prevent cockpit from

taking damage.

Remove the black connector at the backside of

the screen as shown below.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios para automóviles de Car-Interface

Car-Interface

Car-Interface CI-AUX-110 Manual de usuario

Car-Interface

Car-Interface v.LiNK CI-VL2-CIC-F Manual de usuario

Car-Interface

Car-Interface CI-RL3-C3D Manual de usuario

Car-Interface

Car-Interface CI-RL4-MZD88 Manual de usuario

Car-Interface

Car-Interface CI-UCON5-JEEP Manual de usuario

Car-Interface

Car-Interface CI-RL4-R40-E Manual de usuario

Car-Interface

Car-Interface v.LOGiC V5-CIC-F-PNP Manual de usuario

Car-Interface

Car-Interface RL4-MM-R Manual de usuario

Car-Interface

Car-Interface CI-VL7-SY2 Manual de usuario

Car-Interface

Car-Interface TV-Free CI-TF-SC14 Manual de usuario

Car-Interface

Car-Interface CI-RL4-UCON8-CP Manual de usuario

Car-Interface

Car-Interface TV-Free CI-TF-FSYNC54 Manual de usuario

Car-Interface

Car-Interface CI-DAB-MMI2G Guía de instalación

Car-Interface

Car-Interface CI-UCON7-JEEP Manual de usuario

Car-Interface

Car-Interface CI-RL-PCM3-TF Manual de usuario

Car-Interface

Car-Interface CI-CARPLAY-MMI3G Manual de usuario

Car-Interface

Car-Interface TV-Free CI-TF-UCON22 Manual de usuario

Car-Interface

Car-Interface RL4-MBN6 Manual de usuario

Car-Interface

Car-Interface CI-RL4-R40 Manual de usuario

Car-Interface

Car-Interface CI-RL3-SC15 Manual de usuario

Car-Interface

Car-Interface CI-RL2-MBN45 Manual de usuario

Car-Interface

Car-Interface CI-RL4-UCON12 Manual de usuario

Car-Interface

Car-Interface CI-CARPLAY-NTG5 Manual de usuario

Car-Interface

Car-Interface TV-Free CI-TF-C25 Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario

Car-Interface c.LOGiC lite CI-C1-CCC Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas