Motorola I50sx Manual de usuario

CAR KIT OWNER’S MANUAL 1

INTRODUCTION

Congratulations on your purchase of the Car Kit for i85s/i50sx/i55sr

phones. This kit provides a multitude of features that enhance the capa-

bilities of the i85s/i50sx/i55sr phone while integrating it comfortably

into the vehicular environment.

These features include:

• Hands free speaker phone operation

• Remote Push-To-Talk (PTT) capability

• Remote palm microphone compatibility

• Built-in power supply for battery charging

• Benefits of an external vehicular antenna

• Integrated RS-232 or USB data port

OVERVIEW

This Owner’s Manual provides a description of the accessories connec-

tions, power connection, and installation procedure for and basic opera-

tion of this Car Kit.

The following items are supplied with this kit:

1. Junction Box (NNTN4227)

2. Phone Cradle (NNTN4226)

3. 5 Watt External Speaker (SSN4020)

4. Visor Microphone (SMN4107)

5. Power Cable (SKN4922)

NTN9477

Car Kit Owner’s Manual for

i85s/i50sx/i55sr phones

Manuel de l’utilisateur de la

trousse véhiculaire pour les

appareils i85s/i50sx/i55sr

NTN9477A_Condor Car Kit.book Page 1 Monday, January 14, 2002 12:27 PM

2 CAR KIT OWNER’S MANUAL

6. Remote Push-To-Talk (PTT) (NNTN4249)

7. Installation Bracket (TRN5502)

Additional Items Required (not included)

8. Antenna Port Adapter (Carrier Specific)

9. Tested and approved External Antenna

The three Motorola tested and approved antennas that may be used with

this Car Kit are:

a. RAF4136AMM - Magnetic Mount Antenna

b.RRA4914B - Mobile Roof Mount Antenna

c. FAD5524 - Mobile Window Antenna

Optional items (not included)

10. External Palm Microphone (HMN4058)

11. RS232 Data Cable (NKN6544)

12. USB Data Cable (NNTN4007)

13. 24 Volt DC to 12 Volt DC External Converter (NNTN4079)

NTN9477A_Condor Car Kit.book Page 2 Monday, January 14, 2002 12:27 PM

CAR KIT OWNER’S MANUAL 3

SAFETY AND GENERAL INFORMATION

• Refer to your phone’s user guide for safety information relating to

phone operation.

• This document contains important safety and operating instructions.

• Before using this Car Kit, read all the instructions, and cautionary

markings on (1) the Car Kit, (2) the battery, and (3) the portable

phone using the battery.

Antenna and Installation Considerations

• All equipment must be properly installed in accordance with

Motorola installation instructions.

• Ensure the antenna is properly installed external to the vehicle and

in accordance with the requirements of the antenna manufacturer/

supplier.

• Use only the supplied or an approved antenna. Unauthorized

antennas, modifications, or attachments could impair reception

quality, damage the radio product, or result in non-compliance to

United States FCC Regulations for RF exposure.

• Position the antenna in such a way to maintain a separation distance

of at least 8 inches (20 cm) between the antenna connected to the

Car Kit and the body of any user, or nearby person, to assure

compliance with the United States FCC regulations on RF exposure.

W A R N I N G

!VEHICLES EQUIPPED WITH AIR BAGS

An air bag inflates with great force. Do NOT place

objects, including both installed or portable wireless

equipment, in the area over the air bag or in the air

bag deployment area. If in-vehicle wireless equip-

ment is improperly installed and the air bag inflates,

serious injury could result.

NTN9477A_Condor Car Kit.book Page 3 Monday, January 14, 2002 12:27 PM

4 CAR KIT OWNER’S MANUAL

INSTALLATION

Installation Planning

Planning is the key to fast, easy installation. Before a hole is drilled or a

wire is run, inspect the vehicle and determine how and where you intend

to mount the junction box, phone cradle, speaker, visor microphone,

remote PTT button, remote palm microphone (optional), and speaker

(see Figure 1). Plan wire and cable runs to provide maximum protection

from pinching, crushing and overheating.

Figure 1. Car Kit Interconnection Diagram

A properly installed Car Kit will minimize service calls and equipment

downtime. Refer to the following guidelines when planning the installa-

tion:

• Use the provided hardware for mounting.

• Ensure that the cables are not stretched, and not subjected to heat

from engine or transmission.

• Crimp connectors securely.

• Do not attach components to any part of the vehicle that is not rigid

or is subject to excessive vibration.

• Do not run cables over sharp edges that could cause wear or

chaffing of cable insulation.

to Optional Palm

Mic

Fuse Block

External

Microphone

External

Speaker External

Push-to-Talk (PTT)

Optional

USB, RS232

Data Cable

In-Line Fuse

(if connection is made in

to External

Antenna

(Red)

(Black)

(Orange)

(Green)

to Positive Supply

Voltage

to Vehicle Chassis

Ground

to Entertainment

Mute

to Ignition

Phone

Cradle

engine compartment)

NTN9477A_Condor Car Kit.book Page 4 Monday, January 14, 2002 12:27 PM

CAR KIT OWNER’S MANUAL 5

• Do not install the components in locations where they might cause

interference to the operation of the vehicle controls.

• If it is necessary to penetrate the firewall, check opposite side for

cable clearance before drilling and use a grommet to protect the

cable where it passes through.

Recommended Tools

The following tools are recommended for proper installation of your Car

Kit.

• Portable Drill

•Hammer

• Center Punch

• Phillips #2 Screwdriver

Junction Box Installation

In most vehicles, the best location for mounting the junction box is just

under the dash, or under the front seat. It must be protected from dirt and

moisture, and must be afforded adequate space for cooling. There must

also be sufficient space to allow for the connection of accessories.

Figure 2. Junction Box - Accessories Connection Diagram

to Phone Cradle to optional Palm

Mic

to External

PTT

to External

Speaker to External

Microphone to Power

Cable

NTN9477A_Condor Car Kit.book Page 5 Monday, January 14, 2002 12:27 PM

6 CAR KIT OWNER’S MANUAL

DC Power Cable Installation

The Car Kit must be operated only in negative ground electrical systems.

Reverse polarity (positive ground) will trigger protection circuits which

cause the cable fuse to open. Check the groundpolarity before you begin

installation to prevent wasted time and effort. Only 12V DC automotive

systems are directly supported. For 24V DC operation, external con-

verter (NNTN4079) is required.

The DC power cable shipped with the Car Kit is long enough for instal-

lation in most vehicles. Begin the power cable installation in the follow-

ing manner.

1. Route the red and black leads of the main power cable to convenient

chassis ground and positive supply voltage connection points. Ifit is

necessary to penetrate the firewall, use an existing opening or, if

necessary, drill a new hole of approximately 9/16 inch or 3.5 cm.

Insert a grommet into the hole to prevent damage to the power

cable. When making connections on the engine side of the firewall,

additional in-line fuse holders (included) should be used at the con-

nection points.

2. Cut the black lead to the desired length.

• If the connection is to be made under the dash or in the vehicle

cabin, connect the black lead directly to the chassis of the vehicle.

• If connection is made in the engine compartment, connect the black

in-line fuse holder between the black lead of the power cable and

the desired chassis connection point.

3. Cut the red lead to the desired length. This lead will be connected

such that it has positive supply voltage at all times, even when the

vehicle is turned off.

• If connection is to be made under the dash or in the vehicle cabin,

connect the red lead to a positive supply voltage point.

• If connection is to be made in the engine compartment or directly to

the battery, connect the red in-line fuse holder between the red lead

of the power cable and the desired positive voltage connection

point.

It is not good practice to connect the black lead to the

negative (-) battery terminal; the Car Kit could be

damaged if there were a malfunction in the vehicle’s

electrical system.

NOTE:

NTN9477A_Condor Car Kit.book Page 6 Monday, January 14, 2002 12:27 PM

CAR KIT OWNER’S MANUAL 7

Figure 3. Power Connections if electrical connec-

tions are made in engine compartment

4. Route and connect the green lead to a convenient ignition-switched

supply point in the vehicle.

5. If the vehicle’s audio system supports an external muting feature,

route and connect the orange wire to the audio system. Otherwise,

the orange wire may be left unconnected and cut off or tied out of

the way.

Crimp

Firewall

Grommet Red Lead

Connector

BlackLead

In-Line

Fuse Holder

To Positive Supply Voltage

To Vehicle Chassis

Ground

Fuse

In-Line

Fuse Holder

Red Lead

Black Lead

Fuse

Crimp

Connector

An ignition switched accessory terminal can be veri-

fied by measuring the terminal while operating the

vehicle’s key switch. With the ignition key in the

“accessory-ON” position, the terminal voltage

should measure the vehicle’s battery voltage. With

the switch in the “OFF” position, it should measure

near zero.

NOTE:

The Car Kit supports an “Entertainment Mute” func-

tion when connected to an audio system that pro-

vides for external muting. This function is

compatible with systems that mute the audio output

when the control line is connected to ground.

NOTE:

NTN9477A_Condor Car Kit.book Page 7 Monday, January 14, 2002 12:27 PM

8 CAR KIT OWNER’S MANUAL

Phone Cradle Installation

Figure 4. Cradle Unit Installation Detail

When installing the Cradle refer to the following procedure or modify

the procedure to suit your type of vehicle:

1. Using one of the scissor bracket halves as a template, position the

bracket half so that the pivot end of the bracket is toward the bottom

of the Cradle.

a. Using an awl or similar device, make four holes in the carpet at

marked locations. This will prevent damage to the carpet when

drilling.

b. Mark and drill holes, then securely mount the bracket half using

the four metal screws supplies.

c. Secure the cradle to the mounting bracket and connect its cable

to the Junction Box.

PHONE

POCKET

RELEASE BUTTON

CABLE TO

ANTENNA

CABLE TO

JUNCTION BOX

Always use the supplied fastening hardware to rig-

idly secure the Cradle. An unsecured Cradle could

cause a unit to move and interfere with the proper

operation of the vehicle.

NOTE:

NTN9477A_Condor Car Kit.book Page 8 Monday, January 14, 2002 12:27 PM

CAR KIT OWNER’S MANUAL 9

Antenna Installation

The best location for mounting the antenna is the center of a large, flat,

conductive surface. In almost all vehicles, these requirements are best

satisfied by mounting the antenna at the center of the roof. Some vehi-

cles have a large trunk lid that also provides a good antenna location. If

the trunk lid is used, connect grounding straps between the trunk lid and

the vehicles chassis to ensure the trunk lid is adequately grounded.

For best performance, use a low-loss coaxial cable with the highest gain

antenna.

The three Motorola tested and approved antennas that may be used with

this Car Kit are:

1. RAF4136AMM - Magnetic Antenna

2. RRA4914B - Mobile Roof Mount Antenna

3. FAD5524 - Mobile Window Antenna

Use only an approved antenna and refer to the installation instructions of

the antenna you have selected.

External Speaker Installation

A common location for mounting the speaker is on the firewall, beneath the

dashboard, on the passenger’s side of the vehicle. Hanger and trunnion

brackets are provided for mounting the speaker.

1. It is recommended that the speaker be located 3ft (1m) from the

visor microphone. Avoid placing the speaker where it faces the

visor microphone.

2. Place the speaker and speaker cable at least 1 foot (30 cm) away

from any part of the portable phone’s antenna.

Antennas with gain exceeding 9db do not comply

with FCC RF exposures and are not allowed for use

with this product

NOTE:

NTN9477A_Condor Car Kit.book Page 9 Monday, January 14, 2002 12:27 PM

10 CAR KIT OWNER’S MANUAL

Figure 5. External Speaker Installation Location

Carry out the following procedure (refer to figure 5):

1. Using the trunnion bracket as a template, drill the necessary mount-

ing holes and secure the bracket with the provided self-tapping

screws.

2. Position the speaker on the trunnion bracket and secure it using the

provided wing screws.

3. Route the speaker cable to avoid physical damage or visual obstruc-

tion. Allow sufficient slack in the connector end of the cable to reach

the Junction Box (see Figure 2, Junction Box Installation).

4. Plug the speaker cable into the junction box (see Figure 2, Junction

Box Installation).

Dashboard

Firewall

Mounting

Bracket

NTN9477A_Condor Car Kit.book Page 10 Monday, January 14, 2002 12:27 PM

Otros manuales para i50sx

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Accesorios para automóviles de Motorola

Motorola

Motorola T215 Manual de usuario

Motorola

Motorola Bluetooth Wireless Hands Free Manual de usuario

Motorola

Motorola HF800 - Bluetooth hands-free Speakerphone Manual de usuario

Motorola

Motorola T605 - Bluetooth hands-free Car Manual de usuario

Motorola

Motorola HF850 - Deluxe Bluetooth Car Manual de usuario

Motorola

Motorola VC70N0 Manual de usuario

Motorola

Motorola T605 - Bluetooth hands-free Car Manual de usuario

Motorola

Motorola HK105 Manual de usuario

Motorola

Motorola WIRELESS BLUETOOTH CAR KIT CH1324A Manual de usuario

Motorola

Motorola HF800 - Bluetooth hands-free Speakerphone Manual de usuario

Motorola

Motorola VC70N0 Manual de usuario

Motorola

Motorola 6803578F42 Manual de usuario

Motorola

Motorola 68014301013 Manual de usuario

Motorola

Motorola RLN5933 Manual de usuario

Motorola

Motorola ATRIX MB860 Manual de usuario

Motorola

Motorola VC70N0 Manual de instalación y operación

Motorola

Motorola HF850 - Deluxe Bluetooth Car Manual de usuario

Motorola

Motorola HF850 Manual de usuario

Motorola

Motorola HF850 Manual de usuario

Motorola

Motorola TK30 Manual de usuario

Motorola

Motorola 6840420Z01-AD Manual de instrucciones

Motorola

Motorola HS850 - Headset - Over-the-ear Manual de usuario

Motorola

Motorola T225 Manual de usuario

Motorola

Motorola Premium Wireless Car Kit Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario

Prorack

Prorack K1163 Manual de usuario

Curt Manufacturing

Curt Manufacturing A25 Manual de usuario

Motorola i50sx Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas