Molex 207129 Series Manual de usuario

AT 4753 Air Crimp Tool Head

Doc. No: ATS-640077100 Release Date: 04- 1-06 UNCONTROLLED COPY Page 1 of 6

Revision: A Revision Date: 04- 1-06

Air Powered

Crimp Tool Head

VibraKrimp





Application Tooling

pecification heet Order No. 64007-7100

Engineering No. AT4753

FEATURE

 Quick change tool head for the 19 79-0001 (AT- 00)

 Tooling kit is interchangeable with other kits in the 64001 and 64003 Series

 A precision user-friendly terminal locator wire stop holds terminals in the proper crimping position.

 Insulation crimp adjustment allows a precise insulation crimp.

 Pneumatic powered crimp tools help reduce fatigue and discomfort from repetitive manual crimping.

COPE

Products: VibraKrimp™ Female Non-Insulated Quick Disconnects, 4- 6 AWG. This tool head is intended for use

in the 19 79-0001 (AT- 00) either hand held or with optional bench adapter 19078-0307 (ATBA) and foot switch.

Testing

Mechanical

The tensile test, or pull test, is a means of evaluating the mechanical properties of the crimped connections.

The following charts show the UL specifications for various wire sizes. The tensile strength is shown in

pounds and indicates the minimum acceptable force to break or separate the terminal from the conductor.

Wire ize (AWG)

*UL

310

*UL – 310 – Quick Disconnects

The following is a partial list of the product part numbers and their specifications that this tool is designed to run.

We will be adding to this list and an up to date copy is available on www.molex.com.

Wire ize: 24

26 AWG 0.20

0.12mm²

Terminal No.

Terminal Eng No. (REF)

Wire trip Length

Insulation Diameter

Max

imum

In.

19018

0044

417

.17

4.37

.095

.41

19018

0045

417

.17

4.37

.095

.41

19018

0019

4179

.17

4.37

.095

.41

19018

00 0

4179

.17

4.37

.095

.41

AT 4753 Air Crimp Tool Head

Doc. No: ATS-640077100 Release Date: 04- 1-06 UNCONTROLLED COPY Page of 6

Revision: A Revision Date: 04- 1-06

OPERATION

Refer to the instruction manual for the 19 79-0001 (AT- 00) for mounting

this crimp tool head.

Crimping Terminals

1. There are tab locator blades supplied with the tool. One is for .187

and . 50 tabs; the other is for . 05 tabs and .110 tabs. Make sure the

proper blade is installed on the top of the locator and the other is

stored on the bottom of the locator.

. Insert the wire into the terminal. Push the terminal and wire onto the

tab locator all the way to the stop in the proper color-coded nest. The

barrel of the terminal should be up. See Figure 1.

Caution: Never operate this tool without the supplied safety shield in place. Never place fingers in the tool nests.

3. Push on the wire to assure it is still fully seated in the terminal. See Figure and 3. Cycle the tool.

4. Remove the crimp and inspect for proper crimp location, and check for insulation closure. Molex offers a

Crimp Inspection Handbook for closed barrel industrial product. See our website or contact your sales

engineer.

5. If the insulation part of the crimp needs to be adjusted, first disconnect the air source and loosen the M4

screw on the bottom tool jaw and insert a 3/3 hex wrench (supplied) into the bottom of the lower die. See

Figure 4. A clockwise (CW) rotation decreases insulation crimp while a counter-clockwise (CCW) rotation

increases insulation crimp. After adjusting retighten the M4 screw. Reconnect the air source.

TERMINAL

AFETY

HIELD

TAB LOCATOR

Figure 1

LOCATOR

JAW

OPEN

WIRE

TERMINAL

Figure 2

TAB LOCATOR

TERMINAL

BARREL

TAB

LOCATOR

WIRE

CONDUCTOR

PUNCH

IN ULATION

ANVIL

Figure 3

IN ULATION

PUNCH

CONDUCTOR

ANVIL

LOCATOR

TERMINAL

AT 4753 Air Crimp Tool Head

Doc. No: ATS-640077100 Release Date: 04- 1-06 UNCONTROLLED COPY Page 3 of 6

Revision: A Revision Date: 04- 1-06

Maintenance

It is recommended that each operator of the tool be

made aware of, and responsible for, the following

maintenance steps:

1. Remove dust, moisture and other

contaminants with a clean brush, or soft, lint-

free cloth.

2. Do not use any abrasive materials that could

damage the tool.

3. Make certain all pins; pivot points and bearing surfaces are protected with a thin coat of high quality machine

oil. Do not oil excessively. This tool was engineered for durability, but like any fine piece of equipment it

needs cleaning and lubrication for a maximum service life of trouble-free crimping. A light oil, such as 30

weight automotive oil used at the oil points shown in Figure 4, every 5,000 crimps or monthly will significantly

enhance the tool life and ensure a stable calibration.

4. When tool is not in use store the tool in a clean, dry area.

Tool Calibration

A Certificate of Calibration (see last page) was supplied with the

tool. To recalibrate this tool, pin gauge measurements should be

taken in each conductor nest and compared to this chart. The tool

should be lubricated prior to recalibration to ensure consistent

measurements.

Nest Color Code

Wire Range

“X” Dimension

Conductor Crimp

Crimp Inspection Marking

AWG

mm²

Mean

No Go

Red

0. 0

0.1

.04

.039

050

N/A

Warranty

This tool is for electrical terminal crimping purposes only. This tool is made of the best quality materials. All vital

components are long-life tested. All tools are warranted to be free of manufacturing defects for a period of 30

days. Should such a defect occur, we would repair or exchange the tool free of charge. This repair or exchange

will not be applicable to altered, misused or damaged tools.

CAUTION: Molex crimp specifications are valid only when used with Molex terminals, applicators and tooling.

PIN GAUGE IN

CONDUCTOR CRIMP

“Confining” Crimp

LOO EN THE

M4 CREW

LUBRICATION

POINT

(BOTH IDE )

LIGHT OIL (EVERY MONTH

OR 5,000 CRIMP )

Figure 4

3/32” HEX

WRENCH

AT 4753 Air Crimp Tool Head

Doc. No: ATS-640077100 Release Date: 04- 1-06 UNCONTROLLED COPY Page 4 of 6

Revision: A Revision Date: 04- 1-06

PART LI T

Item

Order No

Description

Quantity

64007

7100

Crimp Tool Head

Fig

ure

64005

0000

Basic Air Tool Head

64003

1175

Locator Assembly

64003

7170

Tooling Kit

Tooling Kit Only

64003

710

Conductor Punch

64003

7101

Conductor Anvil

64003

7104

Insulation Punch

64003

7103

Insulation Anvil

N/A

4 mm Dia. by 5.0 mm L

Roll Pins

N/A

#10

3 by 5/16” L

g Cup Pt. Set Screw

1**

** Available from an Industrial supply company such as (MSC 1

800

645

7 70).

Figure 5

M4 LOCKNUT W/HEX

NYLON IN ERT

M4 FLAT WA HER

9 6

(2)

AT 4753 Air Crimp Tool Head

Doc. No: ATS-640077100 Release Date: 04- 1-06 UNCONTROLLED COPY Page 5 of 6

Revision: A Revision Date: 04- 1-06

Figure 6

(4)

(2)

(4)

(2)

Parts List (Continued)

Item

Order No.

Description

Quantity

64005

0000

Basic Air Tool Head

Fig

ure

64005

0103

Nose Guard

64000

0077

Repair Kit (Springs, Rods Pivots ,Rings, and Washers)

N/A

by 1

ong

Freedrive Pan Head Screw

1**

N/A

M4 by 5

ong

Freedrive Pan Head Screw

1**

N/A

3/16” by 3/8” Long Dowel Pin

1**

** Available from an Industrial supply company such as (MSC 1

800

645

7 70).

AT 4753 Air Crimp Tool Head

Doc. No: ATS-640077100 Release Date: 04- 1-06 UNCONTROLLED COPY Page 6 of 6

Revision: A Revision Date: 04- 1-06

Air Powered

Crimp Tool Head

VibraKrimp





Certificate of Calibration

Order No. 64007-7100

Engineering No. AT4753

Tool Order Number __________________

Tool Eng. Number___________________

Tool Revision______________________

Serial Number_____________________

Date of Manufacture

Pin Gauge of Conductor Nest/Nests or Slug height if the nest is the “F” Crimp style.

Range Conductor Nest # 1 = ____________- Actual = ____________-

Technician _______________________-

Date of Calibration __________________-

Calibration should be done every 5,000 cycles or 3 months.

Tools should be lubricated during this operation.

Visit our Web site at http://www.molex.com

Otros manuales para 207129 Series

100

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Herramientas de crimpado de molex

molex

molex 63827-6900 Manual de usuario

molex

molex 63811-4700 Manual de usuario

molex

molex CR60622B Manual de usuario

molex

molex 59354 Manual de usuario

molex

molex AT 2200 Manual de usuario

molex

molex 63813-2100 Manual de usuario

molex

molex 63827-1600 Manual de usuario

molex

molex 63811-6400 Manual de usuario

molex

molex 63823-4500 Guía del usuario

molex

molex 207129 Series Manual de usuario

molex

molex 63903-8900 Manual de usuario

molex

molex 63816-1000 Manual de usuario

molex

molex RHT-4753 Manual de usuario

molex

molex RHT 2761-CC Manual de usuario

molex

molex 63811-6800 Manual de usuario

molex

molex 105300 Series Manual de usuario

molex

molex 63825-7470 Guía del usuario

molex

molex 63811-7200 Manual de usuario

molex

molex 63823-9100 Manual de usuario

molex

molex 63825-2600 Manual de usuario

molex

molex 4D Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 35768 Series Manual de usuario

Manuales populares de Herramientas de crimpado de otras marcas

Panduit

Panduit CT-1000 Guía del administrador

JST

JST CS 10 Manual de usuario

Danfoss

Danfoss ET4200 Manual de usuario

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manual de usuario

TE Connectivity

TE Connectivity 2063528-1 Manual de usuario

Tyco Electronics

Tyco Electronics 69156-1 Manual de usuario

CRH

CRH CRL CBLHCT1 Manual de usuario

Emerson

Emerson Klauke ES 105CFM Manual de usuario

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Manual de instrucciones

Danfoss

Danfoss ET4350 Manual de usuario

Milwaukee

Milwaukee M18 Manual de usuario

HOGERT

HOGERT HT1P169 Manual de usuario

Textron

Textron ESG105L Manual de usuario

Tyco Electronics

Tyco Electronics 90035-3 Manual de usuario

Emerson

Emerson Klauke ES 20RMCCFB Manual de usuario

Continental Refrigerator

Continental Refrigerator PC150HD Manual de usuario

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Manual de usuario

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Manual de usuario