Molex ServiceGrade Guía del usuario

Hand Crimp Tool Open Barrel Terminals

Doc No: ATS-638111000 Release Date: 06- 9-1 Page 1 of 4

Revision: B Revision Date: 10- -1

ServiceGrade





Hand Crimp Tool

Application Tooling

Specification S eet Order No. 63811-1000

FEATURES





 Ergonomic soft grip handles for comfortable crimping with small handle spread





 Accepts material thicknesses of 0.15 to 0.40mm and conductor barrel lengths of .00 to 3.50mm





 Ideal for field repair and prototyping





 Available in custom packaging for customer resale





 Available through distribution only

SCOPE

Products: Molex Open Barrel Crimp Terminals, 14 to 4 AWG

CRIMPING INFORMATION:

Tool Profiles should be selected based on the wire AWG and insulation diameter.

Wire Size Conductor Tool

Section Range Pull Force Min. ▼

AWG

mm2

Lb.

.00

.30

.50

.091

.098

50.0

1.30

.00

.30

.079

.091

133.5

30.0

0.80

1.60

.00

.063

.079

89.0

0.0

0.50

1.40

1.80

.055

.071

57.9

13.0

0.35

1.40

1.60

.055

.063

35.6

8.0

0. 0

1.40

.40

.055

5.0

▼

Each application should be verified for pull force.

Insulation

Diameter Range

Insulation Tool

Section Range

3.50

3.99

.138

0.157

3.90

4.80

.154

.189

3.00

3.50

.118

0.138

3.40

4.80

.134

.189

.49

3.00

.098

0.118

.80

3.90

.110

.154

.01

.49

.079

0.098

.30

3.40

.091

.134

1.50

.01

.059

0.079

1.80

.80

.071

.0140

0.99

1.50

.039

0.059

1.40

.00

.055

.079

3.99

4.50

.157

0.177

4.30

4.80

.169

.189

Restrictions:

Termination crimp quality is dependent on the conductor profile choice and skill of the operator. Customers should

independently verify that intended termination meets quality and performance needs. Not all terminal, wire and

profile combinations will provide minimum pull force requirements, or provide an acceptable crimp form.

Hand Crimp Tool Open Barrel Terminals

Doc No: ATS-638111000 Release Date: 06- 9-1 Page of 4

Revision: B Revision Date: 10- -1

INSULATION

CRIMP

BRUSH

STRIP

LENGTH

BELL MOUTH

CRIMP HEIGHT

BEND

DOWN

BEND UP

ROLLING

CONDUCTOR

CRIMP

TWISTING

DEFINITION OF TERMS

The illustration above is a generic representation of crimp attributes and not an exact image of a particular terminal.

OPERATION

CAUTION: Install only Molex terminals listed above with this tool. Do not crimp hardened objects as damage

can occur to the tool.

WARNING: Make sure that the wire is DISCONNECTED from any power supply

Make sure work area is clean and dry and wear approved eye protection.

Crimping Terminals

1. Select the appropriate Molex terminal.

. Verify that the wire size, terminal material thickness and conductor barrel length are within the specifications

for this tool.

3. Strip the wire to the proper strip length.

4. Open the tool handles and insert the conductor grip area of the terminal into the desired conductor profile. See

Figure 1.

5. Squeeze the tool handles together enough to allow the terminal barrel to touch the top of the profile radii.

6. Align the insulation edge between the conductor and insulation

barrel and then insert the stripped wire into the terminal.

7. Verify that the conductor brush is present. If the wire does not fit

into the terminal, the conductor profile selection may be too

narrow.

8. Holding the wire in place, squeeze the tool handles firmly

together. Use two hands, if necessary.

9. After crimping, if any strands of wire are visible at the top of the

crimp form, the conductor profile selection chosen may be too

wide

10. Open the tool handles and insert the terminal into the desired

insulation section. Evaluate the housing opening before

crimping the insulation. See Figure .

Fig

ure

INSULATION

PUUNCH

TERMINAL

WIRE

Hand Crimp Tool Open Barrel Terminals

Doc No: ATS-638111000 Release Date: 06- 9-1 Page 3 of 4

Revision: B Revision Date: 10- -1

11. Gently squeeze the tool handles together to allow the terminal insulation profile to provide an acceptable strain

relief.

1 . Remove the crimped terminal from the tool. Inspect the crimp for loose wire strands, missing crimp, or other

damage. Any minor terminal bending may be straightened by hand.

Maintenance

It is recommended that each operator of the tool be made aware of, and responsible for, the following maintenance

steps:

1. Remove dust, moisture, and other contaminants with a clean brush, or soft, lint free cloth.

. Do not use any abrasive materials that could damage the tool.

3. Make certain all pins; pivot points and bearing surfaces are protected with a thin coat of high quality machine

oil. Do not oil excessively. Light oil (such as SAE30W oil) applied at

the oil points, shown in Figure 4, every 5,000 crimps or 3 months, is

recommended.

4. Wipe excess oil from hand tool, particularly from crimping area. Oil

transferred from the crimping area onto certain terminations may

affect the electrical characteristics of an application.

5. When tool is not in use, keep the handles closed to prevent objects

from becoming lodged in the crimping dies, and store the tool in a

clean, dry area.

Warranty

This tool is for electrical terminal crimping purposes only. All tools are warranted to be free of manufacturing

defects for a period of 30 days. Should such a defect occur, the tool will be repaired or exchanged free of charge.

This exchange will not be applicable to altered, misused, or damaged tools. This tool is designed for hand use

only. Any clamping, fixturing, or use of handle extensions voids this warranty.

ServiceGrade™ crimp hand tools are low cost tools used in field repair for a limited number of terminations. If a

high quality tool is required or a higher volume of terminations required, please purchase the corresponding

PremiumGrade™ crimp hand tool. A ServiceGrade™ crimp tool may or may not have a terminal locator and in

some case may need the locator removed to operate properly.

CAUTION: Molex crimp specifications are valid only when used with Molex terminals and tooling.

CAUTIONS:

1. Manually powered hand tools are intended for low volume or field repair. This tool is NOT intended for

production use. Repetitive use of this tool should be avoided.

. Insulated rubber handles are not protection against electrical shock. NEVER perform crimps on active

electrical circuits.

3. Wear eye protection at all times.

4. Use only the Molex terminals specified for crimping with this tool.

Fig

ure

Hand Crimp Tool Open Barrel Terminals

Doc No: ATS-638111000 Release Date: 06- 9-1 Page 4 of 4

Revision: B Revision Date: 10- -1

Certification

Molex does not certify or re-certify ServiceGrade™ hand tools but rather supplies the following guidelines for

customers to maintain their hand tools.

% This tool is qualified to pull force only. To re-certify, crimp a terminal to a wire, which has been stripped

1 .7mm (1/ ”) long, so there is no crimping of the insulation. Pull the terminal and wire at a rate no faster than

5mm (1.00”) per minute. See the Molex web site for the Quality Crimp Handbook for more information on pull

testing.

% When the hand tool is no longer capable of achieving minimum pull force, it should be replaced.

Visit our Web site at http://www.molex.com

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Herramientas de crimpado de molex

molex

molex 207129 Series Manual de usuario

molex

molex 63811-7100 Manual de usuario

molex

molex 63811-7100 Manual de usuario

molex

molex CR60930A Manual de usuario

molex

molex 63823-0400 Guía del usuario

molex

molex 207129 Series Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 63827-8200 Manual de usuario

molex

molex 98897 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 63811-4700 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 63816-0900 Manual de usuario

molex

molex 63823-6800 Manual de usuario

molex

molex 64005-4100 Manual de usuario

molex

molex 63811-5700 Manual de usuario

molex

molex HCS-125 Series Manual de usuario

molex

molex 63811-7200 Manual de usuario

molex

molex CR5974 Manual de usuario

molex

molex 63827-0470 Manual de usuario

molex

molex 63825-4800 Manual de usuario

molex

molex 35745 Series Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 63827-1170 Manual de usuario

Manuales populares de Herramientas de crimpado de otras marcas

Panduit

Panduit CT-1000 Guía del administrador

JST

JST CS 10 Manual de usuario

Danfoss

Danfoss ET4200 Manual de usuario

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manual de usuario

TE Connectivity

TE Connectivity 2063528-1 Manual de usuario

Tyco Electronics

Tyco Electronics 69156-1 Manual de usuario

CRH

CRH CRL CBLHCT1 Manual de usuario

Emerson

Emerson Klauke ES 105CFM Manual de usuario

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Manual de instrucciones

Danfoss

Danfoss ET4350 Manual de usuario

Milwaukee

Milwaukee M18 Manual de usuario

HOGERT

HOGERT HT1P169 Manual de usuario

Textron

Textron ESG105L Manual de usuario

Tyco Electronics

Tyco Electronics 90035-3 Manual de usuario

Emerson

Emerson Klauke ES 20RMCCFB Manual de usuario

Continental Refrigerator

Continental Refrigerator PC150HD Manual de usuario

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Manual de usuario

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Manual de usuario

molex ServiceGrade Guía del usuario

Manuales populares de Herramientas de crimpado de otras marcas