Molex 207129 Series Manual de usuario

Hand Crimp Tool for CP 2.8 Receptacle Crimp Terminals

Doc No: ATS-6382343HM Release Date: 01-19-11 UNCONTROLLED COPY Page 1 of 8

Revision: A Revision Date: 01-19-11

CONDUCTOR

BRUSH

STRIP LENGTH

SEAM

CONDUCTOR

CRIMP

CUT-OFF

TAB

BELL MOUTH

BEND UP

TWISTING

ROLLING

BEND

DOWN

WIRE

SEAL

Application Tooling

Specification Sheet

Tool Kit

Order No. 63823-4370

Hand Crimp Tool

Order No. 63823-4300

FEATURES

A full cycle ratcheting hand tool ensures complete crimps

Ergonomically designed soft handles

Precisely designed crimping profiles with simple contact positioning

Easy handling due to outstanding force ratio

Tool kits are easily installed into the Hand Crimp Tool or the 63816-0300 Power Crimp Head which is installed

into the 63816-0200 (110 V) or the 63816-0250 (220 V) Battery Powered Tool.

Many different Tool kits can be used with a single Battery Powered Tool.

This tool is IPC/WHMA-A-620 Class 2 and RoHS compliant.

SCOPE

Products: CP 2.8 receptacle for 18 - 20 AWG type TXL wire and

0.5 –1.0mm2type ID and IR wire with 2.80mm (.110") CMC Wire Seal color RED.

Terminal Series No.

Terminal Order No.

Wire Size and Type

Insulation Diameter

Strip Length

Available in Reel only

AWG

mm²

In.

64324

64324-1049

64324-1149

18-20 TXL

0.5 -1.0 Type ID and IR

1.40 -2.15

.055 -.085

4.90 -5.10

.193 -.201

64324-2049

64324-2149

Customer to cut off terminal from reel: 0.30mm (.012”) maximum Cut-off Tab.

Note: Terminal will accommodate the thin wall small insulation with the TXL type American wires and the ID or IR type metric wires.

DEFINITION OF TERMS

TYPE 4C

Hand Crimp Tool for CP 2.8 Receptacle Crimp Terminals

Doc No: ATS-6382343HM Release Date: 01-19-11 UNCONTROLLED COPY Page 2 of 8

Revision: A Revision Date: 01-19-11

ANVILS

POWER

CRIMP

HEAD

Figure 1

PUNCHES

M4 X 10 LONG

BHCS

M4 X 18 LONG

BHCS

CRIMP SPECIFICATION

Terminal Series No.

Bell Mouth

Bend up Bend down

Twist Roll

Conductor Brush

In.

Degree

In.

64324

0.1-0.5

.004-.020

0.2 - 0.6

.008-.024

Seam: Seam shall not be open and no wire allowed out of the crimping area.

After crimping, the conductor profiles should measure the following (See notes below).

Terminal

Series No.

Wire

Size

Conductor

Insulation

Pull Force

Minimum

Profile

Crimp Height

(Ref)

Crimp

Width

(Ref)

Crimp Height

(Ref)

Crimp Width

(Ref)

AWG

mm2

In.

0.5mm2

20 AWG

0,75mm2

18 AWG

1,0mm2

64324

0.5

1.13-1.23

.044-.048

2.06

.081

4.30-4.50

.169-.177

4.97

.196

15.7

0.52

1.13-1.23

.044 .048

2.06

081

4.30-4.50

.169-.177

4.97

.196

13.0

0.75

1.18-1.28

.046-.050

2.06

081

4.40-4.60

.173-181

4.99

.196

20.2

0.82

1.18-1.28

.046-.050

2.06

081

4.40-4.60

.173-181

4.99

.196

20.0

1.0

1.25-1.35

.049-.053

2.07

.081

4.60-4.80

.181-.189

5.00

.197

115

25.8

Tool Qualification Notes:

1. Pull Force should be measured with no influence from the insulation crimp.

2. The above specifications are guidelines to an optimum crimp.

Note:

A crimp height chart is provided with this manual as Reference Only. Due to the wide range of wires, strands,

insulation diameters, and durometers, actual crimp height measurements may very slightly. An occasional,

destructive, pull force test should be preformed to check hand tool crimp. Pull Force value must exceed the

minimum pull force specifications listed.

CAUTION: Install only Molex terminals listed above with this tool. Do not crimp hardened objects as damage

can occur to the tool or die.

INSTALLATION

To install the Tool Kit into the Power Crimp Head

follow the steps below:

Anvils and Punches Installation

1. Insert the Anvils into the bottom slots of the

nest. Install the M4 x 10 long BHCS and tighten

in place.

2. Insert the Punches into the top slots of the nest.

Install the M4 x 18 long BHCS and tighten in

place. See Figure 1.

Locator Installation and Removal

Follow the steps below to install or replace the locator. See Figure 2.

Hand Crimp Tool for CP 2.8 Receptacle Crimp Terminals

Doc No: ATS-6382343HM Release Date: 01-19-11 UNCONTROLLED COPY Page 3 of 8

Revision: A Revision Date: 01-19-11

SWING

LOCATOR

OPEN

PRESS DOWN

ON THE BRASS

PIVOT SHAFT

LIFT UP ON

THE LOCATOR

Figure 2

SWING OPEN

TERMINAL

PUSH HERE TO

OPEN WIRE STOP

LOCATOR

TERMINAL

IN PLACE

Figure 4

LOCATOR LATCH

IN OPEN POSITION

To install the locator

1. Position the locator with the hole over the brass pivot shaft and snap it

into place.

To remove the locator

1. Open the crimp hand tool and unlock the locator latch.

2. Swing the locator open and away from the hand tool.

3. Firmly press down on the brass pivot shaft with your thumb, while

pulling the locator up. Slip the locator off the top of the brass pivot

shaft.

OPERATION

Open the tool by squeezing the handles together, at the end of the closing

stroke, the ratchet mechanism will release the handles, and the hand tool

will spring open.

Crimping Terminals

1. Select the desired terminal listed in the preceding

charts.

2. Unlock the locator latch and swing the terminal locator

away from the crimp tool shown in Figure 3 and 4.

3. Press down on the wire stop on the locator as shown in

Figure 4. Insert the proper terminal into the proper nest

opening. Make sure when choosing the nest opening, it

will correspond with the correct profile on the hand tool.

4. Return the locator to closed position. Make sure the locator latch is in lock position. Insert the proper wire with

the seal over the terminal. Gently touch the wire stop with the end of the wire and align the seal with the grips

on the terminal. See Figure 5 and 6.

Figure 3

LATCH LOCKED

LATCH UNLOCKED

Hand Crimp Tool for CP 2.8 Receptacle Crimp Terminals

Doc No: ATS-6382343HM Release Date: 01-19-11 UNCONTROLLED COPY Page 4 of 8

Revision: A Revision Date: 01-19-11

LOCATOR

Figure 6

WIRE

INSULATION

PUNCH

CONDUCTOR ANVIL

INSULATION

ANVIL

WIRES AGAINST

LOCATOR STOP

CONDUCTOR

PUNCH

TERMINAL

SEAL

TERMINAL

PRE-STRIPPED

WIRE WITH SEAL

Figure 5

WIRE STOP

BLADE

5. Compress the terminal by squeezing the tool handles until the ratchet mechanism cycle has been completed.

Release handles to open the jaws.

6. Unlock the locator latch and swing the locator open.

Note: The tamper proof ratchet action will not release the tool until it has been fully closed.

7. Remove the crimped terminal from the terminal locator by pressing down on the wire stop and gently pulling on

the wire.

8. Visually inspect the crimped terminal for an acceptable crimp.

For the Battery Power Tool:

1. Cycle the Battery Power Tool to crimp the

terminal to the wire.

2. Remove the crimped terminal from the

terminal locator by pressing down on the

wire stop and gently pulling on the wire.

3. Visually inspect the crimped terminal for

an acceptable crimp.

Maintenance

It is recommended that each operator of the

tool be made aware of, and responsible for,

the following maintenance steps:

1. Remove dust, moisture and other

contaminants with a clean brush, or soft, lint-free cloth.

2. Do not use any abrasive materials that could damage the tool.

IRE

LUBRICATION

POINTS

(BOTH SIDES)

LIGHT OIL

(EVERY MONTH

5,000 CRIMPS)

Figure 7A

Figure 7B

Hand Crimp Tool for CP 2.8 Receptacle Crimp Terminals

Doc No: ATS-6382343HM Release Date: 01-19-11 UNCONTROLLED COPY Page 5 of 8

Revision: A Revision Date: 01-19-11

3. Make certain all pins; pivot points and bearing surfaces in the tool head are protected with a thin coat of high

quality machine oil. Do not oil excessively. This tool was engineered for durability, but like any fine piece of

equipment, it needs cleaning and lubrication for a maximum service life of trouble-free crimping. The use of

light oil, such as 30 weight automotive oil, every 5,000 crimps or monthly, will significantly enhance the tool life

and ensure a stable calibration. See Figure 7A or 7B for lubrication points.

4. Store the tool in a clean and dry area when not in use.

Miscrimps or Jams for Crimp Hand Tools Only

(See Figure 10)

Should this tool ever become stuck or jammed in a partially closed position, Do Not force the handles open or

closed. The tool will open easily by rotating the small slotted screw marked with an arrow. See Figure 10.

Warranty

This tool kit is for electrical terminal crimping purposes only. This tool kit is made of the best quality materials. All

vital components are long life tested. All tools are warranted to be free of manufacturing defects for a period of 30

days. Should such a defect occur, we will repair or exchange the tool kit free of charge. This repair or exchange

will not be applicable to altered, misused, or damaged tools.

CAUTION: Molex crimp specifications are valid only when used with Molex terminals and tooling.

CAUTIONS

1. Manually powered hand tools are intended for low volume or field repair. This tool is NOT intended for

production use. Repetitive use of this tool should be avoided.

2. Insulated rubber handles are not protection against electrical shock.

3. Wear eye protection at all times.

4. Use only the Molex terminals specified for crimping with this tool.

CAUTION: Repetitive use of this tool should be avoided.

Certification

Molex does not certify or re-certify commercial grade hand tools but rather supplies the following guidelines for

customers to re-certify hand tools.

This tool is qualified to pull force only. To re-certify, crimp a terminal to a wire, which has been stripped

12.7mm (1/2”) long, so there is no crimping of the insulation. Pull the terminal and wire at a rate no faster than

25mm (1.00”) per minute. See the Molex web site for the Quality Crimp Handbook for more information on pull

testing.

When the hand tool is no longer capable of achieving minimum pull force, it should be taken out of service and

replaced.

This tool is very difficult to disassemble and reassemble. Customer repair is not recommended.

Hand Crimp Tool for CP 2.8 Receptacle Crimp Terminals

Doc No: ATS-6382343HM Release Date: 01-19-11 UNCONTROLLED COPY Page 6 of 8

Revision: A Revision Date: 01-19-11

The chart below shows all applications for this Tool Kit.

Tool Kit

Order No.

Tool

Order no.

Tool

Description

Power Head

Order No.

Adapter

Description

Figure No.

63823-4370

63810-1050

Hand Crimp Frame (Short)

N/A

63810-1000

Hand Crimp Frame (Long)

N/A

63816-0200

Battery Power Tool (110 V)

63816-0300

Power Crimp Head

63816-0250

Battery Power Tool (220 V)

63816-0300

Power Crimp Head

Applications for the Tool Kit

Hand Crimp Tool

Battery Powered Tool

Figure 8

Figure 9

WARNING: NEVER operate service, install tool kits, or adjust the Power Crimp Head without proper

instruction and without first reading and understanding the instructions in the proper Manual or

Specification Sheet. See Chart above for the correct Manual or Specification Sheet.

WARNING: NEVER install tooling or service this tool while it is into any power source. Make sure the

power is turned off.

CAUTION: Keep fingers away from the crimping area when operating this tool. It may cause severe injury.

CAUTION: Wear safety glasses when operating or serving this tool.

POWER

CRIMP

HEAD

LOCKING PINS

BATTERY

POWERED

TOOL

TOOLING KIT

HAND CRIMP

FRAME LONG

AND SHORT

TOOLING KIT

Hand Crimp Tool for CP 2.8 Receptacle Crimp Terminals

Doc No: ATS-6382343HM Release Date: 01-19-11 UNCONTROLLED COPY Page 7 of 8

Revision: A Revision Date: 01-19-11

RATCHET

RELEASE SCREW

Figure10

M4 X 8mm

LONG BHCS

M4 X 18mm

LONG BHCS

M4 X 10mm

LONG BHCS

WITH TOOL KIT

LOCATOR ONLY

HAND TOOL PARTS LIST

Item Number

Order Number

Description

Quantity

63810-1000

Hand Crimp Frame (Long)

63823-4370

Tool Kit with Locator

63823-4375

Locator (only)

REF

Hand Crimp Tool for CP 2.8 Receptacle Crimp Terminals

Doc No: ATS-6382343HM Release Date: 01-19-11 UNCONTROLLED COPY Page 8 of 8

Revision: A Revision Date: 01-19-11

Figure 11

M4 by 8 Long

BHCS

M4 by 18 Long

BHCS

M4 by 10 Long

BHCS

POWER HEAD PARTS LIST

Item

Order No

Engineering No.

Description

Quantity

63816-0300

Power Crimp Head

63823-4370

Tool Kit with Locator

http://www.molex.com

Otros manuales para 207129 Series

100

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Herramientas de crimpado de molex

molex

molex 207125 Series Manual de usuario

molex

molex HTR4971E Manual de usuario

molex

molex 63811-7400 Manual de usuario

molex

molex CR60639B Manual de usuario

molex

molex 63811-5600 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 63825-9570 Manual de usuario

molex

molex 64001-1000 Manual de usuario

molex

molex 11-01-0101 Manual de usuario

molex

molex 64005-3400 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex MOLEX Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex Avikrimp AT 5762 Manual de usuario

molex

molex AT AFIFG Manual de usuario

molex

molex 63825-7470 Guía del usuario

molex

molex 63819-4400 Manual de usuario

molex

molex 63819-0600 Manual de usuario

molex

molex 63811-6670 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex TPX50-50 Guía del usuario

molex

molex 63816-0900 Manual de usuario

molex

molex 207129 Series Manual de usuario

Manuales populares de Herramientas de crimpado de otras marcas

Panduit

Panduit CT-1000 Guía del administrador

JST

JST CS 10 Manual de usuario

Danfoss

Danfoss ET4200 Manual de usuario

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manual de usuario

TE Connectivity

TE Connectivity 2063528-1 Manual de usuario

Tyco Electronics

Tyco Electronics 69156-1 Manual de usuario

CRH

CRH CRL CBLHCT1 Manual de usuario

Emerson

Emerson Klauke ES 105CFM Manual de usuario

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Manual de instrucciones

Danfoss

Danfoss ET4350 Manual de usuario

Milwaukee

Milwaukee M18 Manual de usuario

HOGERT

HOGERT HT1P169 Manual de usuario

Textron

Textron ESG105L Manual de usuario

Tyco Electronics

Tyco Electronics 90035-3 Manual de usuario

Emerson

Emerson Klauke ES 20RMCCFB Manual de usuario

Continental Refrigerator

Continental Refrigerator PC150HD Manual de usuario

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Manual de usuario

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Manual de usuario