molex 35745 Series Manual de usuario
Hand Crimp Tool for VersaBlade™ Industry standard .070" Terminals
Doc No: TS-6381969HM Release Date: 08-03-10 UNCONTROLLED COPY Page 1 of 6
Revision: B Revision Date: 10-13-10
TYPE 4A
Application Tooling
Specification Sheet
Modular Cri p Head
Order No. 63819-6970
Hand Cri p Tool
Order No. 63819-6900
FEATURES
% full cycle ratcheting hand tool ensures complete crimps
% Ergonomically designed soft handles
% Precisely designed crimping profiles with simple contact positioning
% Easy handling due to outstanding force ratio
% Modular Crimp Head is removable and can be use in the ir Powered Tool Order No.63816-0100,
accompanied by ir Powered Crimp dapter (Order No. 63816-0700).
% Can also be used in the Battery Powered Tool Order No.63816-0200 (110 V) or 63816-0250 (220 V)
accompanied by Battery Powered Crimp dapter (Order No. 63816-0600).
SCOPE
Products: VersaBlade™ Industry standard .070" tab terminals, 24 – 26 WG
Ter inal
Series No.
Ter inal
Order No.
Wire Size Insulation Dia eter Strip Length
IPC/WHMA-A620 Ter inal
AWG ² In. In. In.
35745 35745-0410 24 0.20 1.32-1.45 .052-.057 1.32-1.45 .052-.057 4.0-4.8 .157-.189
26 0.12
35746 35746-0410
35746-0411
24 0.20 1.32-1.45 .052-.057 1.32-1.45 .052-.057 4.0-4.8 .157-.189
26 0.12
35747 35747-0410 24 0.20 1.32-1.45 .052-.057 1.32-1.45 .052-.057 4.0-4.8 .157-.189
26 0.12
35748 35748-0410
35748-0411
24 0.20 1.32-1.45 .052-.057 1.32-1.45 .052-.057 4.0-4.8 .157-.189
26 0.12
To achieve optimum IPC- 620 insulation crimps, use this insulation OD range.
Overall insulation OD specification for terminal.
Hand Crimp Tool for VersaBlade™ Industry standard .070" Terminals
Doc No: TS-6381969HM Release Date: 08-03-10 UNCONTROLLED COPY Page 2 of 6
Revision: B Revision Date: 10-13-10
INSULATION
CRIMP
▲
SEE NOTE
BRUSH
STRIP
LENGTH
BELL MOUTH
CRIMP HEIGHT
BEND
DOWN
BEND UP
ROLLING
CONDUCTOR
CRIMP
TWISTING
DEFINITION OF TERMS
▲Insulation Cri p Note:
Due to the terminal’s insulation grip design and/or
insulation diameter range, this tool uses “overlap”
form geometry in the insulation punch. This produces
an overlap insulation crimp ( 620 – compliant). While
the insulation punch profile may appear “lopsided”,
this is a normal condition for this tool. See figure to
the right. (Some tools with multiple crimp pockets
may not have the “overlap” profile on all pockets).
CONDITIONS:
fter crimping, the crimp profiles should measure the
following (see notes on page 4).
Ter inal
Series No
Wire Size Conductor Cri p (Ref.) Insulation Cri p (Ref.) Pull Force
Mini u Profile
Height Width Height ( ax)
Width
AWG
2
In. In. In. In. N Lb. 24
26
35745 24 0.20
1.00-1.10
.039-.043
1.60-1.80
.063 -.071
2.55 .100 2.30-2.50
.091-.098
29.4
6.61
X
26 0.12
0.90-1.00
.035-.039
1.60-1.80
.063 -.071
2.45 .097 2.30-2.50
.091-.098
19.6
4.41
X
35746 24 0.20
1.00-1.10
.039-.043
1.60-1.80
.063 -.071
2.55 .100 2.30-2.50
.091-.098
29.4
6.61
X
26 0.12
0.90-1.00
.035-.039
1.60-1.80
.063 -.071
2.45 .097 2.30-2.50
.091-.098
19.6
4.41
X
35747 24 0.20
1.00-1.10
.039-.043
1.60-1.80
.063 -.071
2.55 .100 2.30-2.50
.091-.098
29.4
6.61
X
26 0.12
0.90-1.00
.035-.039
1.60-1.80
.063 -.071
2.45 .097 2.30-2.50
.091-.098
19.6
4.41
X
35748 24 0.20
1.00-1.10
.039-.043
1.60-1.80
.063 -.071
2.55 .100 2.30-2.50
.091-.098
29.4
6.61
X
26 0.12
0.90-1.00
.035-.039
1.60-1.80
.063 -.071
2.45 .097 2.30-2.50
.091-.098
19.6
4.41
X
Pull Force should be measured with no influence from the insulation crimp.
The above specifications are guidelines to an optimum crimp.
OPERATION
Open the tool by squeezing the handles together, at the end of the closing stroke, the ratchet mechanism will
release the handles, and the hand tool will spring open.
OVERLAP
INSULATION
CRIMP
OVERLAP FORM GEOMETRY
ANVIL
PUNCH
WIRE
Hand Crimp Tool for VersaBlade™ Industry standard .070" Terminals
Doc No: TS-6381969HM Release Date: 08-03-10 UNCONTROLLED COPY Page 3 of 6
Revision: B Revision Date: 10-13-10
WIRE
INSULATION
PUNCH
TERMINAL
WIRE STOP BLADE
Figure 1
Figure 2
WIRE
TERMINAL
LOCATOR
INSULATION
PUNCH
INSULATION
ANVIL
WIRE STOP
BLADE
CONDUCTOR ANVIL
CONDUCTOR
PUNCH
Cri ping Ter inals
1. Place the terminal into the correct die profile until the terminal stopped by the locator.
2. Bring the wire stop blade down; make sure the wire stop located behind the conductor grip.
3. Place a pre-striped wire into the terminal until the end of wire touching the wire stop. See Figure 2.
4. Close the tool until the ratchet releases, the tool handles will then spring open.
5. Carefully remove the crimped terminal.
Note: The tamper proof ratchet action will not release the tool until it has been fully closed.
Maintenance
It is recommended that each operator of the tool be made aware of, and responsible for, the following
maintenance steps:
1. Remove dust, moisture, and other contaminants with a clean brush, or soft, lint free cloth.
2. Do not use any abrasive materials that could damage the tool.
3. Make certain all pins; pivot points and bearing surfaces are protected with a thin coat of high quality machine
oil. Do not oil excessively. The tool was engineered for durability but like any other equipment it needs
cleaning and lubrication for a maximum service life of trouble free crimping. Light oil (such as 30 weight
automotive oil) used at the oil points, every 5,000 crimps or 3 months, will significantly enhance the tool life.
4. Wipe excess oil from hand tool, particularly from crimping area. Oil transferred from the crimping area onto
certain terminations may affect the electrical characteristics of an application.
5. When tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping dies,
and store the tool in a clean, dry area.
Miscri ps or Ja s
Should this tool ever become stuck or jammed in a partially closed position, Do Not force the handles open or
closed. The tool will open easily by lifting the ratchet release lever. See Figure 6.
Hand Crimp Tool for VersaBlade™ Industry standard .070" Terminals
Doc No: TS-6381969HM Release Date: 08-03-10 UNCONTROLLED COPY Page 4 of 6
Revision: B Revision Date: 10-13-10
Warranty
This tool is for electrical terminal crimping purposes only. This tool is made of the best quality materials. ll vital
components are long life tested. ll tools are warranted to be free of manufacturing defects for a period of 30
days. Should such a defect occur, we will repair or exchange the tool free of charge. This repair or exchange will
not be applicable to altered, misused, or damaged tools. This tool is designed for hand use only. ny clamping,
fixturing, or use of handle extensions voids this warranty.
CAUTION: Repetitive use of this tool should be avoided.
CAUTIONS:
1. Manually powered hand tools are intended for low volume or field repair. This tool is NOT intended for
production use. Repetitive use of this tool should be avoided.
2. Insulated rubber handles are not protection against electrical shock.
3. Wear eye protection at all times.
4. Use only the Molex terminals specified for crimping with this tool.
Notes:
1. This tool should only be used for the terminals and wire gauges specified on this sheet.
2. This tool is not adjustable for crimp height; however crimp force is adjustable (See instructions above).
Variations in tools, terminals, wire stranding and insulation types may affect crimp height.
3. This tool is intended for standard conductor sizes. It may not give a good insulation crimp support for all
insulation sizes.
4. Molex does not repair hand tools (see warranty above). The replacement parts listed are the only parts
available for repair. If the handles or crimp tooling is damaged or worn, a new tool must be purchased.
5. Pull force should be used as the final criteria for an acceptable crimp. Pull force is measured with no
influence from the insulation crimp. The insulation should be stripped long (1/2 in.) so the insulation grips
on the terminal do not grip the wire insulation or the conductor. Refer to Molex Quality Crimping
Handbook 63800-0029 for additional information on crimping and crimp testing.
6. Molex does not certify crimp hand tools.
CAUTION: Molex crimp specifications are valid only when used with Molex terminals and tooling.
Hand Crimp Tool for VersaBlade™ Industry standard .070" Terminals
Doc No: TS-6381969HM Release Date: 08-03-10 UNCONTROLLED COPY Page 5 of 6
Revision: B Revision Date: 10-13-10
MODULAR
CRIMP
HEAD
BATTERY
POWER
B
E
LOCKING
PINS
LOCKING PINS
BATTERY
POWERED
TOOL
AIR
POWER
TOOL
MODULAR
CRIMP HEAD
LOCKING
PINS
LOCKING
PINS
AIR
POWER
CRIMP
ADAPTER
Applications for the Modular Cri p Head
WARNING: NEVER operate, service, install, or adjust this Modular Crimp Head without proper instruction
and without first reading and understanding the instructions in the proper Manual or Specification Sheet.
See Chart below for the correct Manual or Specification Sheet.
WARNING: NEVER install tooling or service this tool while it is into any power source. Disconnect the
power by unplugging or turn off the ctuator from its power source.
CAUTION: Keep fingers away from the crimping area when operating this tool. It may cause severe injury.
CAUTION: Wear safety glasses when operating or serving this tool.
The chart below shows all applications for this Modular Crimp Head.
Modular Cri p Head
Order No.
Tool
Order no.
Tool
Description
Adapter
Order No.
Adapter
Description
Figure
No.
63819-6970
63816-0000
Hand Crimp Frame (Short) N/ N/ 3
63816-0050
Hand Crimp Frame (Long) N/ N/ 3
63816-0200
Battery Power Tool (110 V)
63816-0600
Battery Power Crimp dapter
4
63816-0250
Battery Power Tool (220 V)
63816-0600
Battery Power Crimp dapter
4
63816-0100
ir Power Tool 63816-0700
ir Power Crimp dapter 5
Applications for the Modular Cri p Head
Hand Cri p Tool Battery Powered Tool Air Powered Tool
Figure 3 Figure 4 Figure 5
MODULAR
CRIMP
HEAD
LOCKING
PINS
HAND CRIMP
FRAME LONG
OR SHORT
Hand Crimp Tool for VersaBlade™ Industry standard .070" Terminals
Doc No: TS-6381969HM Release Date: 08-03-10 UNCONTROLLED COPY Page 6 of 6
Revision: B Revision Date: 10-13-10
RATCHET
RELEASE LEVER
HANDLE
SPRING
CRIMPING
SPRING (2)
3
6
4
Figure 6
M4 X 14
LONG BHCS
2
5
1
PARTS LIST
Hand Cri p Tool 63819-6900
Ite
Order Nu ber
Description Quantity
1 63819-6970 Modular Crimp Head 1 (Ref)
2 63816-0050 Hand Crimp Frame (long)
1 (Ref)
3 63819-6975 Locator 1
4 63816-0001 Locking Pin 2
5 63600-0525 Handle Spring 1
6 63600-0520 Crimping Spring 2
http://www.molex.com
Otros manuales para 35745 Series
2
Este manual sirve para los siguientes modelos
12
Tabla de contenidos
Otros manuales de Herramientas de crimpado de molex
molex
molex 63827-2100 Manual de usuario
molex
molex 207129 Series Manual de uso y cuidado
molex
molex 207129 Series Manual de usuario
molex
molex 63823-5200 Manual de usuario
molex
molex 63819-3800 Manual de usuario
molex
molex 63827-1600 Manual de usuario
molex
molex CR60622B Manual de usuario
molex
molex Avikrimp 64005-3000 Manual de usuario
molex
molex 63827-6070 Manual de usuario
molex
molex 63816-1100 Manual de usuario
molex
molex 207129 Series Manual de usuario
molex
molex 69008-1100 Manual de usuario
molex
molex 207129 Series Manual de usuario
molex
molex HCS-125 Series Manual de usuario
molex
molex CR60930A Manual de usuario
molex
molex 63825-0500 Manual de usuario
molex
molex RHT 2761-CC Manual de usuario
molex
molex 207129 Series Manual de usuario
molex
molex 63811-1500 Manual de usuario
molex
molex 63801-8500 Manual de usuario
Manuales populares de Herramientas de crimpado de otras marcas
Textron
Textron ESG105L Manual de usuario
Tyco Electronics
Tyco Electronics 90035-3 Manual de usuario
Emerson
Emerson Klauke ES 20RMCCFB Manual de usuario
Continental Refrigerator
Continental Refrigerator PC150HD Manual de usuario
TE Connectivity
TE Connectivity ERGOCRIMP 1-1579001-3 Manual de usuario
Tyco Electronics
Tyco Electronics CERTI-CRIMP 90418-1 Manual de usuario