Molex 63816-1100 Manual de usuario

Power Crimp Head for Din Style Crimp Dies

Doc No. ATS-6381611 Release Date: 6- 6-13 UNCONTROLLED COPY Page 1 of 2

Revision: B Revision Date: 5-28-14

Power

Crimp Head

for

DIN Style Dies

Applicatio Tooli g

Specificatio Sheet Order No. 63816-1100

FEATURES

 The Quick change Power Crimp Head is easily installed onto the Battery Powered Crimp Tool

(Order No. 63816-1 )

 Powered crimp tools help reduce fatigue and discomfort from repetitive manual crimping and allow portability.

SCOPE

The 63816-11 Power Crimp Head was created for crimping large lug

terminals with the square Din Style crimp dies when used with the Battery

Powered Crimp Tool (Order No. 63816-1 ).

I stallatio

Note: Refer to Operation Manual TM-638161 for further information

regarding the Battery Powered Crimp Tool.

To install the crimp dies into the Power Crimp Head:

1. Slide out the two locking pins that attach the upper die holder portion

of the crimp head to the Power Crimp Tool. The pins come out only

far enough to remove the crimp head. The head will then slide off of

the Power Crimp Tool holder. See Figure 1

2. Pull off the lower die holder from the ram on the Power Crimp Tool.

3 Slide the dies into the grooves of the upper portion of the crimp head

and snap into position on the upper die holder. Then snap the lower

die into the lower die holder. See Figure 2.

4 Re-install the upper and lower portions of the Crimp Head to the

Power Crimping Tool in the reverse order.

Operatio

CAUTION: Never place fingers into the crimping tool jaws.

The 63816-11 Power Crimp Head is parallel acting crimping tool for

modular crimp dies. For operating instructions for crimping terminals

with the Power Crimp Head in the Battery Powered tool, see the TM-

638161 Operation Manual, Section 2.2 Operation.

LOCKING

PINS

UPPER DIE

HOLDER

Figure 1

LOWER DIE

HOLDER

Figure 2

LOWER DIE

HOLDER

LOWER

DIE

UPPER

DIE

Power Crimp Head for Din Style Crimp Dies

Doc No. ATS-6381611 Release Date: 6- 6-13 UNCONTROLLED COPY Page 2 of 2

Revision: B Revision Date: 5-28-14

Mai te a ce

It is recommended that each operator of the tool be made aware of, and responsible for, the following

maintenance steps:

1. Remove dust, moisture and other contaminants with a clean brush, or soft, lint-free cloth.

2. Do not use any abrasive materials that could damage the tool.

3. Make certain all pins, and bearing surfaces in the tool head are protected with a thin coat of high quality

machine oil. Do not oil excessively. This tool was engineered for durability, but like any fine piece of

equipment, it needs cleaning and lubrication for a maximum service life of trouble-free crimping. Use a light

oil, such as SAE 3 weight automotive oil, every 5, cycles or monthly, will significantly enhance the tool

life and ensure a stable calibration.

4. Store the tool in a clean and dry area when not in use.

Warra ty

This tool is for terminal crimping purposes only. This tool is made of the best quality materials. All vital

components are long life-tested. All tools are warranted free of manufacturing defects for a period of 30 days.

Should such a defect occur, we will repair or exchange the tool free of charge. This repair or exchange will not

be applicable to alter, misused, or damaged tools.

CAUTION: Molex specifications are valid only when used with Molex tooling.

Co tact I formatio

For more information on Molex application tooling please contact Molex at 1-8 -786-6539.

Visit our Web site at http://www.molex.com

Tabla de contenidos

Otros manuales de Herramientas de crimpado de molex

molex

molex 63819-9200 Manual de usuario

molex

molex 63827-5470 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 64005-6400 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex AT AFIFG Manual de usuario

molex

molex 207129 Series Guía del usuario

molex

molex 63811-7400 Manual de usuario

molex

molex 63811-5500 Manual de usuario

molex

molex MV-396 Guía del usuario

molex

molex 63827-0470 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 5050731100 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 63828-1900 Manual de usuario

molex

molex 59354 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 63825-1670 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 63811-9370 Manual de usuario

molex

molex AT-200 Manual

molex

molex 207129 Series Manual de usuario

Manuales populares de Herramientas de crimpado de otras marcas

Panduit

Panduit CT-1000 Guía del administrador

JST

JST CS 10 Manual de usuario

Danfoss

Danfoss ET4200 Manual de usuario

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manual de usuario

TE Connectivity

TE Connectivity 2063528-1 Manual de usuario

Tyco Electronics

Tyco Electronics 69156-1 Manual de usuario

CRH

CRH CRL CBLHCT1 Manual de usuario

Emerson

Emerson Klauke ES 105CFM Manual de usuario

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Manual de instrucciones

Danfoss

Danfoss ET4350 Manual de usuario

Milwaukee

Milwaukee M18 Manual de usuario

HOGERT

HOGERT HT1P169 Manual de usuario

Textron

Textron ESG105L Manual de usuario

Tyco Electronics

Tyco Electronics 90035-3 Manual de usuario

Emerson

Emerson Klauke ES 20RMCCFB Manual de usuario

Continental Refrigerator

Continental Refrigerator PC150HD Manual de usuario

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Manual de usuario

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Manual de usuario

molex 63816-1100 Manual de usuario

Manuales populares de Herramientas de crimpado de otras marcas