jbc AL Series Manual de usuario
www.jbctools.com
AL
SOLDER FEED STATION
2
AL / SOLDER FEED STATION
AL-2A /1A /9A
CONTROL UNIT
AL250-B
SOLDERING FEED IRON
AL-SD
STAND
0002401 GUIDE SET
(Ø0,9-Ø1mm solder wire)
OPTIONAL GUIDE SETS
(NOT SUPPLIED):
0002399 Ø0,4-Ø0,5mm
0002402 Ø0,6-Ø0,8mm
0002843 Ø1,1-Ø1,5mm
C250403
CARTRIDGE
0008745
SOLDER REEL STAND
POWER CORD
CL9885
TIPS CLEANING STAND
CL6217
BRUSH
PRE ASSEMBLED:
ww w.j bcto ol s.co m
ww w.j bcto ol s.co m
TIP CLEANING
RANGE
AL250
SOLDERING IRON
ww w.j bcto ol s.co m
AL
SOLDER FEED STATION
S0354
SPONGE
MANUAL MANUAL MANUAL
3
Power Cord
Socket
Main switch
Equipotential
connector
INSTALLATION
0964551Pedal
(Not supplied)
HEAT MANAGEMENT
Work mode: Lift tool from the stand and the
tool tip heats up to the selected temperature.
Sleep mode: When the tool is in the stand, the
temperature reduces (preset sleep temperature
is 180ºC / 360ºF).
Hibernation mode: After longer periods of
inactivity (pre-set to 30 minutes), the power
is cut off and the tool cools down to room
temperature.
Heat management increases tip life which reduces cost of ownership.
JBC stations intelligently manage the tool tip temperature:
4
4
4
3
2
1
1. Open dragging mechanism
2. Place the guide set and
tighten the screws
GUIDE SET
1
2
2
REEL STAND ASSEMBLY
GUIDE SET ASSEMBLY
AL / SOLDER FEED STATION
5
4
3. Take the solder wire from the reel until the guide tube start.
4. Close the dragging mechanism
GUIDE TUBE
START
3
-
+
LOADING
SOLDER WIRE
+
-
6
A
B
5. Connect the handpiece to the station and switch it on. With the handpiece out of the stand, press the
WIRE LOAD key till the solder leaves by the end of the guide tube.
Fast wire
dragging
Solder wire dragging button
A. Adjust the dragging strength
to allow the forwarding of the
solder wire and to avoid stall
and or clogging situations when
any cause arises
B. Tighten the dragging
mechanism
CLUTCH REGULATION
AL / SOLDER FEED STATION
7
CONTROL SCREEN
There are 4 tool status:
USE (Use). The tool is ready to work.
STD (Stand). The tool is placed in the stand but still not in the sleep mode.
SLP (Sleep). The tool is in the sleep mode in the stand, its temperature has dropped till the sleep temperature.
OL. The power circuit is overheated. The power is temporarily not supplied.
TEMP. 230ºC USE
disc. L 10 S 11
Tool temperature Tool status
Length of
wire
Speed
Working method
8
CONTINUE ON NEXT PAGE
PARAMETERS MODIFICATION OF THE TOOL AND THE STATION
To enter into this mode, you must hold the SELECT key for 3 seconds
9
10
Este manual sirve para los siguientes modelos
4
Tabla de contenidos
Otros manuales de Pistola de soldar de jbc
jbc
jbc CD-1BE Manual de usuario
jbc
jbc CP-2E Manual de usuario
jbc
jbc AD 2200 Manual de usuario
jbc
jbc AM 6000 Manual de usuario
jbc
jbc PHNE-K Manual de usuario
jbc
jbc CD Manual de usuario
jbc
jbc WSST Manual de usuario
jbc
jbc MVE-A Manual de usuario
jbc
jbc Premium DIR-D series Manual de usuario
jbc
jbc IR Preheater Set Manual de usuario
Manuales populares de Pistola de soldar de otras marcas
Vishay Precision Group
Vishay Precision Group Micro-Measurements Mark V Instrucciones de montaje
ersa
ersa i-CON 1V Manual de usuario
Hakko Electronics
Hakko Electronics FX-100 Manual de usuario
Weller
Weller WAD 101 Manual de usuario
Weller
Weller WXD 2 Manual de usuario
AlienTek
AlienTek T100 Manual de usuario
