Jbc PHS-1B Manual de usuario

中文 31

Deutsch 21

Español 11

IR Preheater

Ref. PHS-B

English 2

Page

www.jbctools.com

Packing List

The following items should be included:

Heater Unit Console

Power Cord ................................................ 1 unit

Ref. 0009417 (100V/120V)

0009401 (230V)

Thermocouple .......................................... 1 unit

Ref. PH218

Kapton Tape .............................................. 1 unit

Ref. PH217

Manual ......................................................... 1 unit

Ref. 0017241

Ref. PHS-B

IR Preheater

IR Preheater ............................................................................................................................................... 1 unit

Ref. PHS-1B (120V)

PHS-2B (230V)

PHS-9B (100V)

www.jbctools.com

Features

Pedal socket (optional)

Ref. P-005

Heating Areas

Power socket

Power

Fixing brackets for

PHS-SA Convection

Preheater Support

Heater Unit

Console

Control Unit Start / Stop

Auxiliary Thermocouple (Type K) Input

Thermocouple

(Type K)

Ref. PH218

USB-B

connector to PC:

Update software

Zone A

Zone B

www.jbctools.com

Profiles by Temperature

The usual way to run a profile is using the Thermocouple (TC) connected to the Control Input of the

console. JBC offers 3 predefined profiles (JBCset) and 10 profiles ready for you to personalize.

Why Infrared? The most efficient technology for PCB preheating

This is the most advanced, efficient and cost-effective method to preheat PCBs in any soldering job

or rework job. The low thermal mass of the infrared element gives outstanding control of the heat

output and the process temperature. This technology provides fast response, high heating rates and

uniform heating that ensure the best results.

Operation

JBCset profiles

There are 3 profiles predefined by JBC: A, B and C. The difference between them is the number

of steps: 2, 3 or 4. The thicker your PCB is and the more layers it contains, the more steps are

needed to obtain a gradual warming.

These profiles are not modifiable but they can be used as a template to create your own profiles.

JBCset A

2 steps

JBCset B

3 steps

JBCset C

4 steps

For repetitive jobs we recommend running profiles without the Thermocouple (TC). Once any

profile has been run to the end, the system has all the process data which you can save.

Once it is saved, you can run this profile without connecting the Thermocouple (TC). The heating

process will the same as long as the same working conditions are respected.

User profiles

You can create your own profiles from the JBCset profiles. On the work screen of the profile,

press the Enter button and choose the option Edit profile.

Power Mode

The unit works at the selected power or temperature during the defined time. These parameters can

be modified from the work screen by pressing the Enter button and the Edit parameters menu.

To see the current temperature you must plug the Thermocouple (TC) into the Control connector.

PCB reference

specifications:

FR4 1,6mm thick

and 2 layers. FR4 2,2mm thick

and 6 layers.

FR4 1,6mm thick

and 6 layers.

Profiles set using the low position of the PHS-SA Support (28 mm in height between the PCB and the heating area).

Recommended Guidelines

1. Place the Thermocouple (TC) as near as possible to the component being worked on.

2. If there are any sensitive components, use the Auxiliary Thermocouple as protection.

You can select the protection temperature in Station settings. If the selected temperature is

reached, the Heater Unit will stop the process and a warning message will be shown.

3. IPC* does not recommend exceeding ramp-up rates over 3 - 4 °C / sec (5 - 7 °F / sec) so as to

reduce the risk of thermal stress on the PCB.

* IPC was founded in the U.S. in 1957 as the Institute for Printed Circuits and is committed to becoming the

most recognized international industry association for the electronics manufacturing industry.

Fix the TC with Kapton Tape

Auxiliary Thermocouple (TC)

www.jbctools.com

Display Control

www.jbctools.com

Maintenance

Before carrying out maintenance, always allow the equipment to cool.

- Check periodically that the PHS-B is clean.

- Use a damp cloth when cleaning. Alcohol can only be used to clean the metal parts.

Clean

periodically

- Only if it is absolutely necessary and

if cleaning with isopropyl alcohol (IPA) is not

enough, it is recommended to use a scraper

to remove dirt in the glass area.

- Replace any defective or damaged parts.

Use original JBC spare parts only.

- Repairs should only be performed by a JBC

authorized technical service.

Safety

It is imperative to follow safety guidelines to protect health and prevent electric

shock, injury, fire or explosions.

- Do not use the units for any purpose other than PCB preheating. Incorrect use may cause fire.

- The mains cable must be plugged into approved bases. Make sure that it is properly grounded

before use. When unplugging it, hold the plug, not the wire.

- The temperature of accessible surfaces may remain high after the unit is turned off. Handle with care.

- Do not leave the appliance unattended when it is on.

- Do not cover the ventilation grills. Heat can cause inflamable products to ignite.

- Heat can cause inflamable products to ignite even when out of sight.

- Be careful with the remains of liquid tin. In contact with skin, it can cause burns.

- Avoid flux coming into contact with skin or eyes to prevent irritation.

- Be careful with the smoke produced when soldering.

- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when

working to avoid personal harm.

- This appliance can be used by children over the age of eight as well as persons with reduced

physical, sensory or mental capabilities or lacking experience provided that they have been given

adequate supervision or instruction concerning use of the appliance and understand the hazards

involved. Children must not play with the appliance.

- Maintenance must not be carried out by children unless supervised.

www.jbctools.com

Specifications

IR Preheater

PHS-1B 120V. Input 120V 50/60Hz Fuse 8A

PHS-2B 230V. Input 230V 50/60Hz Fuse 4A

PHS-9B 100V. Input 100V 50/60Hz Fuse 8A

- Weight: 2,9 kg (6.39 lb)

- Dimensions (Heater Unit): 195 x 288 x 41,5 mm (7.68 x 11.34 x 1.63 in)

- Maximum Power: 500W

- Heating Area: 65 x 135 mm (2.56 x 5.31 in - 1 zone)

130 x 135 mm (5.12 x 5.31 in - 2 zones)

- Temperature Range: 50 - 250 °C (120 - 482 ºF)

- Temperature Measurement: Thermocouple type K

- JBCset temperature profiles: 3 profiles (2, 3 or 4 steps)

- User Profiles: 20 (up to 6 steps for each)

- Maximum work time: 600 min or indefinite

Complies with CE standards.

ESD protected housing.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Manuales populares de Pistola de soldar de otras marcas

Bakon

Bakon 3200 Manual de usuario

Proxxon

Proxxon Gaslotset MGS Manual de usuario

HAKO

HAKO FX-8804 Manual de usuario

SATA

SATA 02002A Manual de usuario

Velleman

Velleman HRJA151 Manual de usuario

Weller

Weller WSM 1 Manual de usuario

Vishay Precision Group

Vishay Precision Group Micro-Measurements Mark V Instrucciones de montaje

ersa

ersa i-CON 1V Manual de usuario

Hakko Electronics

Hakko Electronics FX-100 Manual de usuario

Weller

Weller WAD 101 Manual de usuario

Weller

Weller WXD 2 Manual de usuario

AlienTek

AlienTek T100 Manual de usuario

Atten

Atten ATETOOL AT-689A Manual de usuario

Surtek

Surtek 112554 Dimensiones y guía de instalación

Parkside

Parkside PLBS 30 A1 Manual de usuario

BlackJack SolderWerks

BlackJack SolderWerks BK8000 Manual de usuario

Weller

Weller WX1 Manual de usuario

multicomp pro

multicomp pro MP740893 Manual de usuario

jbc PHS-1B Manual de usuario

Manuales populares de Pistola de soldar de otras marcas