jbc PK-5A Manual de usuario
Pick and Place unit
Ref. PK-5A
INSTRUCTION MANUAL
www.jbctools.com
Packing List
The following items are included:
Pick and Place
module............................ 1 unit
Ref. PK-5A
Filter Box ........................ 1 unit
Ref. 0005966
It contains 50 filters Ref. 0004716
Power Cord.....................1 unit
Ref. 0022529
Manual .............................1 unit
Ref. 0024027
Cups Set ......................... 1 unit
Ref. 0940163
Bent Needles Set .........1 unit
Ref. 0861660
Straight Needles
Set ............................. 1 unit
Ref. 0901546
Pick and Place
tool......................................1 unit
Ref. T260-A
Pedal.................................. 1 unit
Ref. P-405
2
to Power
Supply to Pedal
Features
to Ground
Power LED
Start/Stop Button
Pick and Place Module
Ref. PK-5A
T260-A
www.jbctools.com
3
Choose the needle and the suction cup that best fits the component and start as follows:
Tool assembly
Suction cups
Insert a needle and attach the
appropriate cup for a correct suction
process.
Make sure the needle does not protrude
from the cup.
Maximum working temp: 250ºC (482ºF)
Needles
4
Suction Release
Cover the pen hole with your finger and lift off
the component.
Operation modes
a) Hand control
Press the button to activate or stop the
suction.
Lift your finger to release the component.
Hold the pen so the hole is accessible to your
finger tip.
www.jbctools.com
5
Keep your finger on the pen hole.
ReleaseSuction
Press the pedal to start the suction Lift your foot to release the component
Keep suction button off to allow pedal
function.
b) Pedal control
6
Maintenance
Spare filter
Ref. 0005966
O Ring
Ref. 0007717
Filter cover
Ref. 0004710
Before carrying out maintenance or storage, always unplug the equipment.
- Keep the casing clean by using a damp cloth. Specially use a soft cloth for the front side.
- Periodically check all cable and tube connections.
- Keep filters clean to ensure proper suction and replace them when necessary.
- Use original JBC spare parts only.
- Do not work with defective or damaged pieces.
- Repairs should only be performed by a JBC authorized technical service.
- Maintenance must not be carried out by children unless supervised.
www.jbctools.com
7
- Do not use the units for any purpose other than soldering or rework. Incorrect use may cause fire.
- The power cord must be plugged into approved bases. Be sure that it is properly grounded
before use. When unplugging it, hold the plug, not the wire.
- Do not work on electrically live parts.
- Do not leave the appliance unattended when it is on.
- Do not cover the ventilation grills. Heat can cause inflamable products to ignite.
- Avoid flux coming into contact with skin or eyes to prevent irritation.
- Be careful with the fumes produced when soldering.
- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when
working to avoid personal harm.
- Utmost care must be taken with liquid tin waste which can cause burns.
- This appliance can be used by children over the age of eight and also persons with reduced
physical, sensory or mental capabilities or lack of experience provided that they have been given
adequate supervision or instruction concerning use of the appliance and understand the hazards
involved. Children must not play with the appliance.
Safety
Notes
It is imperative to follow safety guidelines to prevent electric
shock, injury, fire or explosion.
8
Notes
www.jbctools.com
9
Notes
10
Tabla de contenidos
Otros manuales de Pistola de soldar de jbc
jbc
jbc RBA-A Manual de usuario
jbc
jbc AL-9A Manual de usuario
jbc
jbc BD Manual de usuario
jbc
jbc CP-9QF Manual de usuario
jbc
jbc NAN Manual de usuario
jbc
jbc CL7889 Manual de usuario
jbc
jbc DIS-D Manual de usuario
jbc
jbc CA Series Manual de usuario
jbc
jbc AL-2A Manual de usuario
jbc
jbc CDES Manual de usuario
Manuales populares de Pistola de soldar de otras marcas
Vishay Precision Group
Vishay Precision Group Micro-Measurements Mark V Instrucciones de montaje
ersa
ersa i-CON 1V Manual de usuario
Hakko Electronics
Hakko Electronics FX-100 Manual de usuario
Weller
Weller WAD 101 Manual de usuario
Weller
Weller WXD 2 Manual de usuario
AlienTek
AlienTek T100 Manual de usuario
