Jbc CD Manual de usuario

www.jbctools.com

Reference Guide

SOLDERING

STATION

SOLDERING

STATION

Reference Guide Reference Guide

T210

T245

SOLDERING HANDPIECES

CL6210 Brass Wool

S0331 Sponge

CD / SOLDERING STATION

CONTENTS

CONTROL UNIT

T210-A

SOLDERING IRON

C210001

C210008

CARTRIDGES

C245003

C245007

CARTRIDGES

MANUAL

POWER CORD

T245-A

SOLDERING IRON

MANUAL

SUPPLIED WITH

CD-2SB / CD-1SB / CD-9SB

SUPPLIED WITH

CD-2BB / CD-1BB / CD-9BB

TOOL SUPORT ADJUSTEMENT

CABLE COLLECTOR

SPONGE

The smoothest cleaning method.The sponge has to be kept wet (not soaked) using distilled water.

S0331 Sponge S0354 Sponge

CL6210 Brass Wool

Very effective cleaning

method. Leaves a small

layer of solder on the tip so

it prevents from oxidizing

between cleaning and re-

wetting.

Depending on your needs you can choose

between 3 diferent cleaning methods , Sponge,

Metal wool (brass or Inox) and brush.

TIPS CLEANING

CL6205 Inox Wool

A bit more agressive on the tip than the brass

wool.

Provides a deeper cleaning on the tip.

TAPING

Tap smoothly the cartridge on the wiper proﬁle

to remove the excess of solder

WIPING

Use the slots to wipe any posible particle

sticked on the tip

WIPER

OPTIONAL TIPS CLEANING

CL6220 Brushes

More agressive on the tip than the wool.

It cleans the tip very well but it should be used

gently.

INSTALLATION

JBC stations intelligently manage the tool temperature:

Work mode: When the tool is used, pre-set work temperature is 350º C.

Sleep mode: When the tool is in the stand, the temperature goes down to 180º C (depending of the conﬁguration).

Hibernation mode: After longer periods of inactivity (pre-set i.e 30 minutes), the power is cut off and the

tool cools down to room temperature.

Heat management increase tip life which reduces cost of ownership.

HEAT MANAGEMENT

Power Cord

Socket

Main switch

Equipotential

connection

CONTROL UNIT

T210-A or T245-A

SOLDERING IRON

SETTINGS

Selected temp.

350

Power 10%

350

Decrease & move down Increase & move up

Tip temperature

% Instant power supplied to the tool

Access Menu

Conﬁrm

Selection

WORKING

Main menu

Counters

Tool settings

Exit

1 Reset settings

Station settings

Tool settings

Plugged hours 0

Working hours 0

Sleep hours 0

Fix one temp -----

Temp levels set OFF

Sleep delay 0 min

4 Counters

Program version

Hibernation hours 0

No tool hours 0

6 Sleep cycles

Sleep temp 180

Hibernationdelay

0 min

Temp adjust + O

Tool 245

Back

ORIGINAL PIN: 0105

Station settings

1 Temp unit

Celsius

Maximum temp 400

Minimum temp 200

Help text OFF

5 Beep ON

6 Power limit 130W

Change PIN

Back

WARRANTY

JBC’s 2 years warranty guarantees this equipment against all ma-

nufacturing defects, covering the replacement of defective parts

and all necessary labour.

Warranty does not cover product wear due to use or mis-use.

In order for the warranty to be valid, equipment must be returned,

postage paid, to the dealer where it was purchased enclosing this

fully ﬁlled in, sheet.

MORE INFORMATION

www.jbctools.com

SERIAL Nº

STAMP OF DEALER

DATE OF PURCHASE

0010333-0211

TECHNICAL SPECIFICATIONS

- Temperature selection from 90 to 450°C (±5%).

- Power: 75W.

- Safety transformer, mains separator and double isolation, with temperature protection fuse.

- CD-2BB / CD-2SB 230V control unit. Input: 230V 50/60Hz. Output: 24V.

- CD-1BB / CD-1SB 120V control unit. Input: 120V 50/60Hz. Output: 24V.

- CD-9BB / CD-9SB 100V control unit. Input: 100V 50/60Hz. Output: 24V.

- Total weight of unit: 2,6 Kg.

- Complies with CE standards on electrical safety, electromagnetic compatibility and ESD protected housing

“skin effect”.

- RoHS compliant.

- Equipotential connector and the tool tip are connected to station mains ground supply for ESD protection.

This product should not be

thrown in the garbage.

Tabla de contenidos

Manuales populares de Pistola de soldar de otras marcas

Bakon

Bakon 3200 Manual de usuario

Proxxon

Proxxon Gaslotset MGS Manual de usuario

HAKO

HAKO FX-8804 Manual de usuario

SATA

SATA 02002A Manual de usuario

Velleman

Velleman HRJA151 Manual de usuario

Weller

Weller WSM 1 Manual de usuario

Vishay Precision Group

Vishay Precision Group Micro-Measurements Mark V Instrucciones de montaje

ersa

ersa i-CON 1V Manual de usuario

Hakko Electronics

Hakko Electronics FX-100 Manual de usuario

Weller

Weller WAD 101 Manual de usuario

Weller

Weller WXD 2 Manual de usuario

AlienTek

AlienTek T100 Manual de usuario

Atten

Atten ATETOOL AT-689A Manual de usuario

Surtek

Surtek 112554 Dimensiones y guía de instalación

Parkside

Parkside PLBS 30 A1 Manual de usuario

BlackJack SolderWerks

BlackJack SolderWerks BK8000 Manual de usuario

Weller

Weller WX1 Manual de usuario

multicomp pro

multicomp pro MP740893 Manual de usuario

jbc CD Manual de usuario

Manuales populares de Pistola de soldar de otras marcas