Intermec EasyCoder PD41 Manual de usuario

Installation

Instructions

Cutter Kit

for the EasyCoder®

PD41 and PD42 Printers

ii EasyCoder PD41/PD42 Cutter Kit Installation Instructions

Intermec Technologies Corporation

Worldwide Headquarters

6001 36th Ave. W.

Everett, WA 98203

U.S.A.

www.intermec.com

e information contained herein is provided solely for the purpose of

allowing customers to operate and service Intermec-manufactured equipment

and is not to be released, reproduced, or used for any other purpose without

written permission of Intermec Technologies Corporation.

Information and speciﬁcations contained in this document are subject to

change without prior notice and do not represent a commitment on the part

of Intermec Technologies Corporation.

e word Intermec, the Intermec logo, Norand, ArciTech, Beverage

Routebook, CrossBar, dcBrowser, Duratherm, EasyADC, EasyCoder, EasySet,

Fingerprint, INCA (under license), i-gistics, Intellitag, Intellitag Gen2,

JANUS, LabelShop, MobileLAN, Picolink, Ready-to-Work, RoutePower,

Sabre, ScanPlus, ShopScan, Smart Mobile Computing, SmartSystems, TE

2000, Trakker Antares, and Vista Powered are either trademarks or registered

trademarks of Intermec Technologies Corporation.

ere are U.S. and foreign patents as well as U.S. and foreign patents pending.

Two screws Two cable clips

Cutter cover

Cutter spring

Two screws

(for plastic)

Cutter Mechanism

EasyCoder PD41/PD42 Cutter Kit Installation Instructions 3

Installing the Cutter

1Unpack your cutter kit and check that all parts depicted below are included.

If not, contact your Intermec sales representative.

2Make sure the printer is turned oﬀ and disconnected from the power

supply. Remove the screw that holds the front cover. Remove the front

cover.

4 EasyCoder PD41/PD42 Cutter Kit Installation Instructions

3Open the side door and remove the tear bar, held by two Phillips

screws.

4Attach the cutter mechanism to the printer using the two Phillips screws

included in the kit.

EasyCoder PD41/PD42 Cutter Kit Installation Instructions 5

Cable clips

Cutter cable

Cutter

connector

5Plug the cutter cable into the connector in the center section as shown.

Secure the cable to the bottom plate using the two cable clips included in

the kit.

6Use the two plastic screws to attach the cutter spring to the cover (1). Hook

the cutter cover onto the cutter mechanism and lock the cover with the

screw at the bottom (2).

6 EasyCoder PD41/PD42 Cutter Kit Installation Instructions

Activating the Cutter (PD42 only)

If you are using a PD42 printer you can activate the cutter directly from the

display.

To activate the cutter on a PD42 printer

1Turn the printer on.

2Press Setup ( ).

3Navigate to Conﬁguration > Cutter >Enable.

4Press Acknowledge ( ).

5Press Setup again to exit setup.

Controlling the Cutter (Fingerprint)

e cutter function is controlled with the Fingerprint commands CUT and

CUT ON/OFF. Please refer to the Fingerprint Programmer’s Reference Manual

(P/N 937-005-xxx) for more information.

Controlling the Cutter (IPL)

e cutter function is controlled with the IPL commands listed below. Please

refer to the IPL Programmer’s Reference Manual (P/N 066396-xxx) for more

information.

IPL Cutter Commands

Command Description

<SO> Cut

<SI>c1 Enable cutter

<SI>c0 Disable cutter

EasyCoder PD41/PD42 Cutter Kit Installation Instructions 7

Installing Media

To install media in the printer, follow the instructions provided in the printer’s

user’s guide. e cutter is primarily intended to cut paper-based media in the

form of continuous stock. To obtain optimal use of the cutter, make sure your

media corresponds to the speciﬁcation below.

Recommended minimum label/paper length 30 mm

Maximum label/paper width 114 mm

Recommended media thickness 78 - 175 μm

Conﬁgure your cutter so that it only cuts through the label liner.

If you cut through both label and liner, the adhesive sticks to the

cutting blade and this causes malfunction. Also avoid cutting

soft, plastic-based media.

Intermec Technologies Corporation

Worldwide Headquarters

6001 36th Avenue West

Everett, WA 98203

U.S.A.

tel 425.348.2600

fax 425.355.9551

www.intermec.com

P/N 1-960657-01

EasyCoder PD41/PD42 Cutter Kit Installation Instructions

*1-960657-01*

Otros manuales para EasyCoder PD41

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios de impresora de Intermec

Intermec

Intermec EasyCoder 201II Manual de usuario

Intermec

Intermec PW50 Manual de usuario

Intermec

Intermec EasyCoder PD4 Manual de usuario

Intermec

Intermec EasyCoder 501 SA Manual de usuario

Intermec

Intermec EasyCoder 3400e Manual de usuario

Intermec

Intermec 825-192-001 Manual de usuario

Intermec

Intermec PC43d Manual de usuario

Intermec

Intermec EasyCoder PF2i Manual de usuario

Intermec

Intermec EasyCoder F2 Manual de usuario

Intermec

Intermec EasyCoder 4420 Manual de usuario

Intermec

Intermec EasyCoder F4 Manual de usuario

Intermec

Intermec PC43t Manual de usuario

Intermec

Intermec PB42 Manual

Intermec

Intermec EasyCoder 501 SA Manual de usuario

Intermec

Intermec EasyCoder F2 Manual de usuario

Intermec

Intermec EasyCoder 501 SA Manual de usuario

Intermec

Intermec EasyCoder PF2i Manual de usuario

Intermec

Intermec PB50 Manual de usuario

Intermec

Intermec EasyCoder PC4 Manual de usuario

Intermec

Intermec 3400 Manual de usuario

Intermec

Intermec 3240 Manual de usuario

Intermec

Intermec Font Card Manual de usuario

Intermec

Intermec EasyCoder 3400e Manual de usuario

Intermec

Intermec PW50 Manual de usuario

Manuales populares de Accesorios de impresora de otras marcas

Star Micronics

Star Micronics TSP800 Series Manual de usuario

REA

REA JET HR pro 2K Manual de usuario

HP Laserjet,Color Laserjet 4si Manual de usuario

oliser

oliser MS 45 Manual de usuario

Roland

Roland DU2-64 Instrucciones y recetas

Xerox

Xerox EFI EXP6000 Manual de usuario

Canon

Canon Finisher-T1 Manual de usuario

Sharp

Sharp FO-1MK Manual de usuario

Labelmate

Labelmate PM-300 Manual de usuario

Epson

Epson T6248 Manual de funcionamiento

Epson

Epson OT-BZ20 Manual de usuario

Canon

Canon TonerRobot EP-27 Manual de usuario

Ricoh

Ricoh LCIT RT5100 Guía de inicio rápido

GBC

GBC 16 Series Manual de usuario

Canon

Canon INNER 2-WAY TRAY-E1 Manual de operación y mantenimiento

Develop

Develop SD-509 Manual de usuario

Kyocera

Kyocera KM-6230 Manual

Triumph Adler

Triumph Adler DF-710 Manual