Intermec EasyCoder 501 SA Manual de usuario

EasyCoder 501/601

Dual Serial Interface Kit

P/N 1-960345-02

Edition 2

September 1998

Installation Instructions

EasyCoder 501/601 – Installation Instructions

DUAL SERIAL INTERFACE KIT

The Serial Interface Board adds two serial communication ports

("uart2:" and "uart3:") to the standard serial communication port

("uart1:").

The printer's software detects when a Serial Interface Board is

installed and adds communication and buffer setup options for the

two additional communication ports.

When a Serial Interface Board is fitted, the following types of

interfaces become available:

"uart1:"

Fittedonprinter'sCPUboard.

RS232C Standard.

RS422or20mACL Option.Additionalcircuits required.

"uart2:"

FittedonSerial Interface Board.

RS232C

"uart3:"

FittedonSerial Interface Board.

RS232C or 20 mA CL Selectedbymeans of strap.

The Dual Serial Interface Kit consists of:

• 1 Serial interface board assy.

• 2 Screws MRX-Z 3 ×6 FZB (not intended for EasyCoder 501/

601)

• Installation Instructions

Introduction

"uart1:"

"uart3:"

"uart2:"

230V

Note:

Illustrations show an EasyCoder 501.

The principles for fitting this optional

equipment in an EasyCoder 601 are

exactly the same.

EasyCoder 501/601

Dual Serial Interface Kit

Installation Instructions

Edition 2, September 1998

Part No. 1-960345-02

EasyCoder 501/601 – Installation Instructions

Continued!

DUAL SERIAL INTERFACE KIT, cont'd.

Step-by-Step Installation

Instructions

Communication

Port "uart1:"

Cover Plate

Power

Switch

Power Cord

Receptacle

The only tool required is a Torx #T10 screwdriver.

❑Turn off the power and remove the power cord.

❑Remove the communication cable from communication port

"uart1:".

❑Open the right-hand door.

❑Remove the eight Torx screws that hold the cover over the left

part of the printer (see illustration below).

❑Remove the cover.

Screws (4x)

Cover

230V

Screws (4x)

EasyCoder 501/601 – Installation Instructions

❑Remove the existing cover plate.

❑Make sure that the CPU board is strapped and equipped for the

desired type of communication on "uart1:" (see the EasyCoder

501 or EasyCoder 601 Technical Manual). Once the interface

boardhasbeenfitted,itwillbedifficult toaccesstherearpartof

the CPU board.

❑FittherequiredstrapsontheSerialInterfaceBoardasdescribed

on page 5.

❑Connect the cable from the interface board to connector P-4 at

the bottom rear corner of the CPU board. Be careful so the

interface board and the CPU board do not come in contact with

eachother,whichpossiblymaycausedamageorshort-circuiting.

❑Fit the interface board assembly to the printer's rear plate from

theinsideasillustratedbelowusingthesamescrewsthatheldthe

removed cover plate.

DUAL SERIAL INTERFACE KIT, cont'd.

Step-by-Step Installation

Instructions, cont'd.

Continued!

Connect to P-4

on CPU Board

Rear Plate Serial

Interface Board

"uart3:"

(male DB25

connector)

"uart2:"

(female DB25

connector)

Screw

EasyCoder 501/601 – Installation Instructions

DUAL SERIAL INTERFACE KIT, cont'd.

Continued!

Step-by-Step Installation

Instructions, cont'd. ❑Reassemble the printer in reverse order.

❑Connect the communication cables to their respective connec-

tors. Please refer to page 6 for pinout descriptions.

❑Connect the power cord and turn on the power.

"uart1:"

"uart3:"

Serial Interface

Board Assy.

"uart2:"

230V

EasyCoder 501/601 – Installation Instructions

DUAL SERIAL INTERFACE KIT, cont'd.

Straps

Thefollowing straps areusedto set upthedesired type ofinterface

on the communication ports "uart2:" and "uart3:".

Communication Port "uart2:"

There are no straps for controlling the RS 232C interface on

"uart2:".

Communication Port "uart3:"

RS 232C:

StrapfittedonP-3betweenpin1–2(rightandmiddlepins)selects

RS 232C.

20 mA Current Loop:

Strap fitted on P-3 between pin 2 – 3 (middle and left pins) selects

20 mA current loop.

External +5V:

External +5V (max. 200 mA) can be made available on pin 16 by

fitting a strap on P-6.

Be careful not to enable this option unintentionally, which may

cause harm to the connected terminal, computer or other device.

"uart3:"

"uart2:"

P-3

P-6

EasyCoder 501/601 – Installation Instructions

DUAL SERIAL INTERFACE KIT, cont'd.

Informationinthismanualissubjecttochangewithoutpriornoticeanddoesnotrepresentacommitment

on the part of Intermec Printer AB.

EasyCoder is a registered trademark of Intermec Technologies Corp.

Torx is a registered trademark of Camcar Division of Textron Inc.

"uart2:" is a DB25 female connector.

"uart3:" is a DB25 male connector.

The mounting holes are connected to chassis ground.

Connector Configuration

Pin "uart2:" "uart3:" Used for: Remarks

DB25female DB25male "uart2:" "uart3:"

1 GNDC GNDC RS232C RS 232C Cableshield

2 TXDA TXDB RS 232C RS232C Transmitted data fromprinter

3 RXDA RXDB RS232C RS232C Receiveddata toprinter

4 RTSA RTSB RS232C RS 232C RTSfromprinter

5 CTSA CTSB RS232C RS 232C CTStoprinter

6 DSRA DSRB RS232C RS232C DSRto printer

7 GNDI GNDI RS232 C RS 232C Signalground

8 – – – – not used

9 – +20M1 – Currentloop + 20 mA

10 – –20M1 – Currentloop - 20 mA

11 – +TXD – Currentloop TXD +

12 – –TXD – Currentloop TXD –

13 – +20M2 – Currentloop + 20 mA *

14 – –20M2 – Currentloop – 20 mA *

15 – – – – not used

16 – +5VEXT – RS232C/CL + 5V max 200 mA.(if strap fitted on P-6)

17 – – – – not used

18 – +RXD – Currentloop RXD +

19 – – – – not used

20 DTRA DTRB RS 232C RS232C DTRpermanently high

21 – – – – not used

22 – – – – not used

23 – – – – not used

24 – – – – not used

25 – –RXD – Currentloop RXD –

*/.In case of printer being activereceiver.

Otros manuales para EasyCoder 501 SA

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios de impresora de Intermec

Intermec

Intermec 3400 Manual de usuario

Intermec

Intermec EasyCoder PF2i Manual de usuario

Intermec

Intermec EasyCoder 3400e Manual de usuario

Intermec

Intermec EasyCoder PF2i Manual de usuario

Intermec

Intermec EasyCoder 201II Manual de usuario

Intermec

Intermec Font Card Manual de usuario

Intermec

Intermec PB42 Manual de usuario

Intermec

Intermec EasyCoder PD41 Manual de usuario

Intermec

Intermec PW50 Manual de usuario

Intermec

Intermec PA30 Manual de usuario

Intermec

Intermec PB42 Manual

Intermec

Intermec EasyCoder 3400e Manual de usuario

Intermec

Intermec EasyCoder PF2i Manual de usuario

Intermec

Intermec EasyCoder 601XP Manual de usuario

Intermec

Intermec PB42 Manual

Intermec

Intermec PB42 Manual

Intermec

Intermec EasyCoder PF2i Manual de usuario

Intermec

Intermec 3240 Manual de usuario

Intermec

Intermec 3400 Manual de usuario

Intermec

Intermec EasyCoder PF4i Manual de usuario

Intermec

Intermec PC43t Manual de usuario

Intermec

Intermec PC43d Manual de usuario

Intermec

Intermec EasyCoder PF2i Manual de usuario

Intermec

Intermec EasyCoder 3400d Manual de usuario

Manuales populares de Accesorios de impresora de otras marcas

Star Micronics

Star Micronics TSP800 Series Manual de usuario

REA

REA JET HR pro 2K Manual de usuario

HP Laserjet,Color Laserjet 4si Manual de usuario

oliser

oliser MS 45 Manual de usuario

Roland

Roland DU2-64 Instrucciones y recetas

Xerox

Xerox EFI EXP6000 Manual de usuario

Canon

Canon Finisher-T1 Manual de usuario

Sharp

Sharp FO-1MK Manual de usuario

Labelmate

Labelmate PM-300 Manual de usuario

Epson

Epson T6248 Manual de funcionamiento

Epson

Epson OT-BZ20 Manual de usuario

Canon

Canon TonerRobot EP-27 Manual de usuario

Ricoh

Ricoh LCIT RT5100 Guía de inicio rápido

GBC

GBC 16 Series Manual de usuario

Canon

Canon INNER 2-WAY TRAY-E1 Manual de operación y mantenimiento

Develop

Develop SD-509 Manual de usuario

Kyocera

Kyocera KM-6230 Manual

Triumph Adler

Triumph Adler DF-710 Manual