gofanco HDWirelessKVM Manual de usuario
Wireless HDMI KVM
Extender 1080p - 150m
User's Guide
G4-0098B
P/N: HDWirelessKVM
2
Thank you for purchasing from gofanco. Our products
aim to meet all your connectivity needs wherever you
go. For optimum performance and safety, please read
the instructions carefully and keep this User's Guide for
future reference. If you need more information about
our products, please visit www.gofanco.com. For
For drivers or manual download, please go to
www.gofanco.com/downloads.
Important Safety Notices
Pleasereadsafetyinstructionscarefullybeforeinstallation
and operation.
• Please pay close attention to all warnings and hints
for this device
• Do not expose this unit to rain, heavy moisture, or
liquid
• Do not put any items into the device or attempt to
modify its operation
• Do not repair the device or open the enclosure
without professional guidance to avoid electric
shocks. Doing so may void your warranty
• Keep the product in a well-ventilated location to
avoid damage from overheating
• Shut off power and make sure environment is safe
before installation
• Do not plug the HDMI cables and IR cables
in/out when the device is in use to avoid cable
damage. Make sure they are plugged into the
correct ports
• Use the included DC5V power adapters only. Make
sure the specification matches if using 3rd-party
DC power adapters
3
Introduction
The Wireless HDMI KVM Extender 1080p - 150m extends
HDMI signals from a source device to a display device
with KVM (2 USB ports) extension wirelessly up to 492ft
(150m). It requires no cables between the Transmitter
(TX) and Receiver (RX), making the installation easy and
clean. Great for homes and offices.
Note: Wireless transmission distance will vary due
to the environmental conditions. Thick walls, brick,
glass, electronic interference, and wireless signals
from other devices will shorten the wireless
transmission distance or cause signal loss.
Features
• Transmits HDMI signals in 1080p up to 492ft (150
meters) wirelessly
• KVM extension with 2 USB ports to control the
source device, such as a PC, at a remote location
• Supports Full HD 1080p with near zero latency
• IR extension allows the source device to recognize
remotecommandsfromaremotelocation.20-60KHz
IR frequency
• HDMI loop-out on the transmitter to connect a local
display, allows easy monitoring of the source signal
• No cables required between Transmitter (TX) and
Receiver (RX)
• Dual antenna maximizes wireless reception with
stable data transmission
4
PackageContents
• Wireless HDMI KVM Extender 1080p - 150m
(1 Transmitter unit & 1 Receiver unit)
• IR blaster cable and IR receiver cable (1 each)
• Antenna (4pcs)
• Power adapter (2pcs)
• User guide
Installation Requirements
1. HDMI source device (DVD player, set top box, PC,
etc.)
2. HDMI display device (SDTV/Monitor, HDTV/
Monitor, projector, etc.)
3. HDMI cables (not included)
4. USB keyboard and USB mouse for KVM control
(optional)
Product Layout
Figure 1: Front Panel (TX & RX)
1 2 3
1. WiFi LED: Slow flashing green when detecting
wireless signal; fast flashing green when detected
and transferring data
2. Pairing LED: Flashing red when detecting signal;
solid red when paired
3. Power LED: Solid red when powered on; solid blue
when HDMI source device is detected
5
Figure 2: Transmitter Rear Panel (TX)
1 2 3 4 5 6 7 1
1. Antenna (x2): Connects to the included antenna
2. Local HDMI Output: Connects to your local HDMI
display
3. HDMIInput:ConnectstoyourHDMIsourcedevice
4. Micro USB: Connects to your PC's USB port using
the included Micro USB to Type-A cable
5. IR Out: Connects to the IR blaster cable
6. PowerJack:Connectstotheincludedpoweradapter
7. Power Switch: Powers On/ Off the transmitter
Figure 3: Receiver Rear Panel (RX)
1 2 3 3 4 5 6 1
1. Antenna (x2): Connects to the included antenna
2. HDMIOutput:Connectstoyourlocal HDMIdisplay
3. USB Type-A (x2): Connects to your keyboard and
mouse
4. IR In: Connects to the IR receiver cable
5. PowerJack:Connects to the includedpoweradapter
6. Power Switch: Powers On/ Off the receiver
6
Hardware Installation
1. Power off all devices including your HDMI source
and HDMI display(s).
2. Install the included antennas to the TX and RX.
3. Connect your HDMI source device to the
Transmitter'sHDMI Input connectorwithanHDMI
cable (HDMI cable not included).
4. Optional: Connect your local HDMI display to the
Transmitter's Local HDMI Output connector with
an HDMI cable (HDMI cable not included). This
connection allows you to monitor the HDMI signal
from the source device location.
5. Optional: Connect the IR Blaster cable to the
Transmitter's IR interface port. Face the eye
towards your HDMI source device's IR window.
This connection is needed only if you need to
control your HDMI source from the remote
location.
6. Connect your HDMI display to the Receiver's
HDMI Output connector with an HDMI cable
(HDMI cable not included).
7. Optional: Connect the IR Receiver cable to the
Receiver's IR interface port. This connection is
needed only if you need to control your HDMI
source from the remote location.
8. Plug your keyboard and mouse into the USB ports
of the Receiver (RX) unit.
9. Plug the included power adapters into the
Transmitter's and Receiver's Power Jacks, then
plug both power adapters into reliable power
outlets. Power on the transmitter and receiver.
7
ApplicationDiagram
Figure 4: IR Control
10. Power on your HDMI source device and HDMI
display(s). The wireless KVM extender is ready for
use.
Note: For optimal signal range, install in a clear
environment with few obstacles. Wireless signals
from other devices, such as microwaves, wireless
mice and keyboards, etc. may interfere with
transmission. Contact our technical support team
if you have specific questions.
Figure 5: Keyboard and Mouse Control
8
Notice
• Wireless signals transmitted through walls, glass,
brick or other solid objects will cause signal loss
and decrease the transmission distance
• Externalwireless signals frommicrowaves, wireless
mice and wireless keyboards will interfere with
HDMI signal transmission
• Keep the unit in a well ventilated environment to
prevent it from overheating
•DONOTexposetheunit to rain,moisture, or liquids
•DO NOT place anything on the unit
•DO NOT open the housing, doing so will void the
warranty and may cause personal injury due to
electronic hazard
•DO NOT plug-in or remove the IR cables when the
unit is powered on
9
FAQ & Troubleshooting
Q: The Wireless Connection LED is on, but no video
output on the remote display:
A: 1) Check the HDMI source device is powered on.
2) Check the transmitter's HDMI Signal LED is on.
3) Check the HDMI cables for solid connection. Use
different HDMI cables if necessary.
4) Connect the HDMI source device directly to the
display to see if there is a signal.
Q: Poor video quality:
A: 1) Check the HDMI cables are connected properly.
Use different HDMI cables if necessary.
2)Changetheangleof the antenna on the transmitter
unit and receiver unit. Generally, the antenna angle
should be positioned as far apart as possible.
3)Adjustthepositionoftransmitter unit and receiver
unit, and make sure they are within the required
signal range.
4) Remove other wireless signals and move any
obstacles that are blocking the signal line-of-sight.
5) Decrease the distance between the transmitter
unit and the receiver unit.
10
Specifications
TX: Description
Video Output Resolution 1080p60, 1080p50, 1080p24, 720p60, 720p50,
576p50, 480p60, 1080i60, 1080i50
Video Input Resolution 1080p60, 1080p50, 1080p24, 720p60, 720p50,
576p50, 480p60, 1080i60, 1080i50
HDMI Compatibilty HDMI 1.4
Digital Audio Support 48/44.1 KHz, 16bit, Digital audio compliant
Latency 16ms (Tx+Rx, 720p60); 60ms (Tx+smartphone)
Power Amplification 20dBm
Wireless Connectivity 2.4GHz
Wireless Transmisson
Distance 492ft (150 meters) line-of-sight
Power Adapter 5V/2A
Power Consumption 12.5 Watts (max)
RX:
Video Output Resolution 1080p60, 1080p50, 1080p24, 720p60, 720p50,
576p50, 480p60, 1080i60, 1080i50
HDMI Compatibilty HDMI 1.4
Digital Audio Support 48/44.1 KHz, 16bit, Digital audio compliant
Latency 16ms (Tx+Rx)
Power Amplification 20dBm
Wireless Connectivity 2.4GHz
Wireless Transmisson
Distance 492ft (150 meters) line-of-sight
Connectivity Keyboard and Mouse KVM extension
Power Adapter 5V/2A
Power Consumption 7.5 Watts (max)
Tabla de contenidos
Otros manuales de Extensor de gofanco
gofanco
gofanco HDBITT4K22 Manual de usuario
gofanco
gofanco HDMIExt8P Manual de usuario
gofanco
gofanco HDBaseT Manual de usuario
gofanco
gofanco HDExt24-HD20 Manual de usuario
gofanco
gofanco KVMHD20Ext Manual de usuario
gofanco
gofanco HDwireless10x1 Manual de usuario
gofanco
gofanco AudioCATExt Manual de usuario
gofanco
gofanco HDwireless100-LT Manual de usuario
gofanco
gofanco USBCwireless Manual de usuario
gofanco
gofanco HD20Ext-Cas Manual de usuario
gofanco
gofanco HDExt50 Manual de usuario
gofanco
gofanco HDExtCoax Manual de usuario
gofanco
gofanco G4-0014A Manual de usuario
gofanco
gofanco HDwireless100 Manual de usuario
gofanco
gofanco PRO-HDBaseT-U Manual de usuario
gofanco
gofanco HDwireless1x4 Manual de usuario
gofanco
gofanco HDwireless200 Manual de usuario
gofanco
gofanco AudioCATExt500 Manual de usuario
gofanco
gofanco HDMIExt2 Manual de usuario
gofanco
gofanco HDbitTPro Manual de usuario
