Dancover CA119071 Manual de usuario
06-07-2017
for
Tunnel Garage (Car), ECO
2,5x5,15x2,15m
Manual
TABLE OF CONTENTS
1. GENERAL INFORMATION…………………………………………………………………..3
1.1 Introduction………………………………………………………………………………........3
2. BOX DESCRIPTION AND TECHNICAL SHEET…………………………………………..4
2.1 General description……………………………………………………………………………4
2.2 Components……………………………………………………………………………………5
2.3 Fabric’s characteristics………………………………………………………………………..7
3. INSTALLATION…………………………………………………………………………..........8
3.1 Handling and transport…………………………………………….......................................8
3.2 Place and requirements for the installation………………………………………….….…..8
3.3 Installation………………………………………………………………………………..…….9
3.3.1 Package opening……………………………………………………………………..….….9
3.3.2 Box installation…………………………………………………………………………… ...9
4. BOX UTILIZATION……………………………………………………………………………11
5. CHECKS AND MAINTENANCE……………………………………………………….........12
6. DISASSEMBLY………………………………………………………………………………..12
2
1. GENERAL INFORMATION
1.1. Introduction
This manual is an integral part of the product; it is addressed to the installer and to the final user of
the box, and enables a correct installation and use. For this reason it must be hold with the box
until proper disposal.
In this manual you will find the instructionsto:
correctly install the box
understandthe functions of the box and of the whole thereof
correctly do the box scheduled maintenance processes
take care of the basic safety rules
ATTENTION: the installer and the final user must read the whole manual in each part of
it. Keepthis manual in a safe and accessible place.
Before using the box, please read carefully the technical information contained in this
manual and follow them strictly.
3
•
•
•
•
4
1. BOX DESCRIPTION AND TECHNICAL SHEET
1.1. General description
The box must be used only as an ordinary protection cover, for purely temporary use. In case of
bad weather conditions (wind, snow), the box must be removed. Given that the box can not be
fixed to the ground - but only bound to it - its use in these conditions can cause damages to
people and things.
It is particularly important for safety not to hang or apply any type of load at the structure or at the
top cover of the box.
In particular, children must not handle the structure. The failure to respect the conditions of use
and warnings immediately voids the warranty.
BOX TUNNEL / BOX TUNNEL €CO
STADIO BOX
A
(cm)
:
412/515/618/721/824/…
B (cm): 250/280/300
C (cm): 185/200/205
A
(cm)
:
412/515/618/721/824/…
B (cm): da 150 a 300
D (cm): da 180 a 240
NB. Starting from the length (A) of cm 700(only for mobile version): eyelets placed on the
lateral profile for ground-fixation through straps and stakes/ballasts (not supplied by the supplier)
1.2. Components
N. DESCRIPTION
1 ALUMINIUM PROFILE MM 40x35
2 PVC LG 550/STARPOL ECO TOP COVER
3** WINDOW IN MICRO-PERFORATED MATERIAL
4** PVC GABLE END WITH WINDOW IN MICRO-PERFORATED MATERIAL
5* PVC BUCKLE
6* STRING FASTENER HANDLE IN PVC
7* NYLON STRING DIAM. MM 5
8* GROUND-FIXING BRACKETS (base v.), CARABINER (mobile v.)
9 CROSSES CM 120X120 (in the mobile v. includes also tension bar)
10* TENSION BARS
11* PVC SLIDING CURTAIN
12* PVC WALL WITH WINDOW IN MICRO-PERFORATED MATERIAL
13* ALUMINIUM CROSSBEAM
14* GROUND-FIXING BRACKETS* (base v.), NYLON WHEELS (mobile v.)
*Only for Box Tunnel and Box Tunnel Eco
*Only for Box Tunnel
5
6
7
13
14
12
7
1.3. Fabric’s characteristics
POLY LG 550/LAC 2L FLAME-RETARDANT
BOX TUNNEL – STADIO BOX
Yarn Warp: 100% PES 1100 Dtex
Weft: 100% PES 1100 Dtex
Fabric’s weight 550 gr/m2
Characteristics ABUV
Finishing gloss lacquered
Breaking strength Warp: ca 250 DaN/5 cm
(DIN 53354) Weft: ca 180 DaN/5 cm
Tear strength Warp: 25 DaN
(DIN 53363) Weft: 20 DaN
Grip (IVK/PKT 14) 10 DaN/5 cm
Temperature resistance +70° C/- 30° C
Light resistance (DIN 53388) Level: 7/8
Fire-proofing ADR cl. II
8
STARPOL ECO
BOX TUNNEL ECO
Yarn Warp:100% PES/1100 Dtex
Weft:100% PES/1100 Dtex
Fabric’s weight Ca 610 gr/m2
Finishing PVC coated
Breaking strength Warp: ca. 235 DaN/5 cm
(DIN 53354) Weft: ca. 220 DaN/5 cm
Tear strength Warp: ca. 23 DaN
(DIN 53363) Weft: ca. 22 DaN
Grip (DIN 53357) 9 DaN/5 cm
Temperature resistance +70° C /- 30° C
3.INSTALLATION
3.1. Handling and transport
The box installation should only be done by qualified staff.
The products must be unloaded through appropriate lifting equipment, which must be used only by
authorized staff.
If the unloading operation is made by hand, it is important to consider that the weight limit that each
male person can handle is 25 Kg; moreover, the operators should be equipped with gloves and
safety shoes.
3.2. Place and requirements for the installation
Before the arrival of the installers the user must arrange:
•any permits required by local regulations
•appropriate ground
P
H
O
T
O
1
3.3. Installation
Before starting the installation, if electrical equipment utilization is needed:
•
make sure you do not work in wet areas
•
use only intact extension cords, according to the place of use
•
use shoes with rubber soles
ATTENTION: It is necessary for the operators to use appropriate personal protective
equipment such as safety shoes and gloves, in order to avoid injuries provoqued by the
fall of the packaging or of components that it contains, perforation and cutting due to
cutting or hanging parts
3.3.1. Package opening
Packaging must be opened only with scissors with rounded tips, using the best care not to cut the
cloth of the article (Photo 1).
NOTE: The packaging material disposal is at user’s charge, who will perform it in
accordance with existing environmental norms.
3.3.2 Box installation
The sliding door must be opened (photo 2) and only the screws of the lower part of the crosses
must be released with an Allen key (photo 3).
ATTENTION: if the screws in the crosses top are released, it can provoque serious
damages to the structure and to the cloth of the box. The supplier is not responsible for
this kind of damages.
9
10
Subsequently, the box must be opened by pushing the c osses f om the bottom to the top (photo 4/a and
4/b).
The top cove must be st etched:
•BASE VERSION: using the st etching device (not included) and tightening the sc ews of the lowe
pa t of the c osses (photo 5/a, 5/b and 5/c)
•MOBILE VERSION: putting the tension ba s in egula position, at 180° (photo 6/a and 6/b); th ough
the egulation of the tenso sc ews, the e will be a bette top cove tensioning
P
H
O
T
O
2
P
H
O
T
O
3
P
H
O
T
O
4/A
P
H
O
T
O
5/A
P
H
O
T
O
5/B
P
H
O
T
O
4/B
Tabla de contenidos
Otros manuales de Carpa de Dancover
Dancover
Dancover ProShed MS572012 Manual de usuario
Dancover
Dancover Proshed Garage Manual de usuario
Dancover
Dancover ST01100 Manual de usuario
Dancover
Dancover PRO XL Manual de usuario
Dancover
Dancover SEMI PRO 7x7m Manual de usuario
Dancover
Dancover 2m Series Manual de usuario
Dancover
Dancover PARTY TENT SEMI PRO CombiTent 8m Series Manual de usuario
Dancover
Dancover Pagoda Marquee UNICO 6x6m Manual de usuario
Dancover
Dancover 3m storage pro Manual de usuario
Dancover
Dancover SEMI PRO 6x12m Manual de usuario
Dancover
Dancover Titanium Manual de usuario
Dancover
Dancover CA119011 Manual de usuario
Dancover
Dancover 5.4m Series Manual de usuario
Dancover
Dancover ST145080 Manual de usuario
Dancover
Dancover Pagoda Tent EventZone Manual de usuario
Dancover
Dancover Marquee 10x15 m PRO+ EventZone Manual de usuario
Dancover
Dancover CombiTent SEMI PRO AC18026 Manual de usuario
Dancover
Dancover Pagoda 4x4m Manual de usuario
Dancover
Dancover Titanium Manual de usuario
Dancover
Dancover Oceancover PVC Manual de usuario
