Dancover Marquee 10x15 m PRO+ EventZone Manual de usuario
29-06-2016
Manual
for
Marquee 10x15 m
PRO+ EventZone
2
Table of contents
Page
1. Introduction 004
1.1 General 005
1.2 Tools for assembly 006
2. Aligning the marquee and the base plate 007
2.1 Laying the base plates 007-008
3. Pre-assembly 009
3.1 Pre-assembly of posts, bars and braces 010-012
3.2 Assembling the braces 013-014
4. Assembling the marquee 015
4.1 Installation of the tie frame 015-018
4.3 Assembling the pediment support 017
5. Assembly of the covers 019
5.1 Roof covers 020-021
5.2 Side and pediment covers 022-023
5.3 Pediments 024
5.4 (If required) Assembling the foot tubes 024-025
6. Disassembly 026
7. Warning instructions 027
7.1 Marquee construction 027
7.2 Transport and storage 027
7.3 Routine visual inspections 027
8. Technical data 028
8.1 Marquee construction 028
8.2 Covers 029
8.3 Standards 029
3
1.Introduction
The following assembly manual describes the installation and assembly
of your marquee by using systematic structure.
Please follow the instructions continuously and execute step by step.
Certain points have additional information if required.
!!!Attention!!!
Please follow accident prevention regulations
Ensure that there is no cable, pipes etc. below the
marquee!!!
On the structure of this assembly manual:
Drawings and sketches are used to explain individual steps for the
assembly and to identify individual components.
Drawings and sketches should be understood as principle
representation and thus they do not necessarily correspond to
the actual dimensions. Supplementary comments are also provided,
where required, to provide a better understanding.
4
1.1 General
Please read this manual thoroughly before starting assembly. Perform
the assembly stop only if all the points are clear, the components are
identified and follow the sequence.
Please follow accident prevention regulations.
Improper handling, non-adherence of rules may result in mortal injury.
Follow the sequence of this assembly manual.
At least 4 persons are required for installing the marquee.
Safety instructions:
- Ensure that all the eaves are correctly mounted.
- Rope braces must be tightened loosely after assembly.
- Defective or damaged components must be replaced immediately with
original spare parts.
- Removal of diagonal braces is forbidden.
- Secure all the bolts after assembly so that they do not slide out.
- Wear protective clothing (e.g. gloves) to prevent injuries.
- Use the supplied tools for assembly.
Please note:
The model approval (test log) contains requirements, specifications,
conditions and operating instructions for "mobile constructions". It should
be kept at the installation location for review by relevant authorities if
required. Each new installation should be communicated to the relevant
authorities.
In addition, the "Guidelines for the construction and operation of mobile
constructions", accident prevention regulations as well as relevant safety
regulations and standards shall be applicable (trade association). These
regulations must be strictly followed.
Assembly helpers should be instructed about possible hazard before they
start the assembly. At least one expert (supervisor) should take
responsibility for supervision during installation and removal. Expert here
means that the person has knowledge of the work processes and the
required safety measures.
5
1.2 Tools for assembly
Assembly and disassembly should always be done with appropriate
Assembly tools.
An assembly rod, see image 1, is supplied with each marquee.
Additional Site tools and equipment:
3 x towing rope snap hooks (load capacity at least 250 kg)
------------------------------------------------------------------------------------------------
2 x ratchet or wrench
------------------------------------------------------------------------------------------------
2 x ladder
------------------------------------------------------------------------------------------------
1 x sledgehammer / ground anchor impact tool
------------------------------------------------------------------------------------------------
1 x tape measure
------------------------------------------------------------------------------------------------
1 x pipe wrench
------------------------------------------------------------------------------------------------
1 x machinist's hammer
------------------------------------------------------------------------------------------------
1 x line with 2x marquee length
------------------------------------------------------------------------------------------------
1 x forklift with telescopic jib (optional)
------------------------------------------------------------------------------------------------
1 x for disassembling the marquee: anchor snag (optional)
6
2.Aligning the marquee and the base plate
It is recommended to align the basic dimensions of the marquee to local
conditions such as road path, building front and similar.
Exact position should be followed when distributing and positioning the
base plate. Wrongly or inaccurately positioned base plates will make
further assembly difficult.
Required assembly tools and materials:
2.1 Aligning the base plates
Note: Keep the ground anchor protruding by approx. 5 cm so that later
readjustment is possible.
2.1.1 Select orientation front.
2.1.2 Stretch line (marquee length + 2m on each side).
2.1.3 Align 1st base plate parallel to the line according to Fig. 1 and strike
the ground nails.
7
2.1.4 Now stretch line for the marquee width and align at right angle
(exact alignment follows).
2.1.5 Measure marquee width from the centre of the 1st base plate to the
centre of the 2nd base plate, align base plate parallel to the line and fix
with ground anchors (see Fig. 2, page 9).
2.1.6 At the line for the marquee length, lay out the 3rd base plate in
parallel. Measure the exact truss distance (TD) from the centre of the 1st
base plate to the centre of the 3rd base plate and fix 3rd base plate with
ground anchors.
2.1.7 According to Fig. 2, measure TD between 1st base plate and 2nd
base plate and mark point B. Measure at the line between 1st base plate
and 3rd base plate and mark point A.
2.1.8 If there is a diagonal line between points A and B, then the right
angle is guaranteed, if not the line between the 1st and 2nd base plate
should be pushed such that the required dimension is achieved.
2.1.9 1. Readjust base plate if required and align again to the line. Check
the marquee width between 1st base plate and 2nd base plate once
again and fix 3rd base plate 3 with ground anchors.
2.1.10 Similarly align 4th. base plate to the line for the marquee length.
Measure exact TD between the centre of 3rd base plate to the centre of
the 4th base plate and fix 4th base plate ground anchors.
2.1.11 Repeat above steps until all the base plates of a marquee side are
fixed.
2.1.12 Starting from the 2nd base plate, align the base plate for the
opposite marquee side and fix with ground anchors.
2.1.13 It is recommended to carry out a final inspection of the marquee
dimension between the centres of four external base plates.
8
3. Preassembly
9
3.1 Pre-assembly of posts, bars and braces
Assembly of posts and bars
Combine and match all components according to Fig. 4 (page 9) and 5
(page 11).
Lay out the components according to the images and following
description.
3.1.1 Push the left and right bar into the ridge shoe and connect with
pivot pins / screws.
3.1.2 Insert the posts with the corresponding rail connectors into the bars
and bolt with pivot pins.
3.1.3 Insert the trusses (completely mounted posts and bars) into the
base plate, bolt with foot bolts and secure with clip connectors.
(Important: It should be ensured that the holes in the foot bolts for the clip
connector are on the outer side of the marquee due to later assembly of
the foot tube.
3.1.4 Place and lay out pediment support / crossbeams at the respective
end trusses.
3.1.5 Sort and lay out flex holders (intermediate rails), ridge and eave
rails.
10
Tabla de contenidos
Otros manuales de Carpa de Dancover
Dancover
Dancover Multipavillon 6x6m Manual de usuario
Dancover
Dancover Basic-1339H Manual de usuario
Dancover
Dancover PRO EventZone 9m Series Manual de usuario
Dancover
Dancover SEMI PRO 7x7m Manual de usuario
Dancover
Dancover CombiTent SEMI PRO AC18026 Manual de usuario
Dancover
Dancover Pagoda 4x4m Manual de usuario
Dancover
Dancover Teepee Manual de usuario
Dancover
Dancover Patio Cover Expert 3x5m Manual de usuario
Dancover
Dancover Pole Tent Semi PRO 6x6m Manual de usuario
Dancover
Dancover Titanium Manual de usuario
Dancover
Dancover Semi PRO 9x12m Manual de usuario
Dancover
Dancover Semi PRO 5x10m Manual de usuario
Dancover
Dancover 5.4m Series Manual de usuario
Dancover
Dancover B788 Manual de usuario
Dancover
Dancover Storage Tent PRO Manual de usuario
Dancover
Dancover CA119011 Manual de usuario
Dancover
Dancover GH18001 Manual de usuario
Dancover
Dancover PVC 4m Series Manual de usuario
Dancover
Dancover PRO EventZone 9m Series Manual de usuario
Dancover
Dancover AQUILA Manual de usuario
