Dancover Oceancover PVC Manual de usuario

26-09-2014-QJ

5,5x15x4,1x5,3m

Manual

Boat tent Oceancover PVC

Safety Advice

Attention

In some countries approval is needed to set up a marquee/tent larger than 75 m2. It is

your responsibility to comply with local rules and regulations and to ensure that the

marquee/tent is assembled correctly.

In case of bad weather conditions, it is your responsibility to ensure the marquee/tent is

safely secured and that the marquee/tent does not cause damage to others.

close to the tent.

The marquee/tent must be safely secured. We recommend you secure your marquee/tent

with straps and pegs as soon as it is assembled.

Make sure to check if the marquee/tent is covered by your home contents

insurance.

Marquees/tents must be evacuated under extreme weather conditions.

In the event of snow always remove snow from the roof of the marquee/tent regularly to

prevent snow from building on the roof as heavy snow can cause the marquee/tent to

collapse.

In the event of rain there is a risk of rain puddles building up on top of the roof of the

marquee/tent. Heavy rain puddles can cause the roof to collapse. It is your responsibility

to ensure rain puddles do not build up. As a precaution, make sure the roof of the

marquee/tent is stretched out properly and adequately over the side frames of the

marquee/tent and remove rain water regularly.

Do not unpack or repack your marquee/tent in freezing temperatures. In case of

temperatures below zero always unpack and repack your marquee/tent indoors to avoid

the risk of cracking parts.

The marquee/tent must be totally dry before you repack and store it to avoid mildew.

Warranty Information

Please visit dancovershop.com for information on warranty.

Please always check our website for the latest safety advice and manuall.

This structure is not tested for snow and wind loads. We always recommend that

you remove snow from the roof. This is a none-permanent structure.

Congratulations on your purchase of our instant shelter. This unit is a combination

of excellent manufacturing and design. It is comprised of a rigid frame and a durable

cover. For easy assembly, we have marked all the parts with codes, with proper

installation, use and maintenance, your unit will provide many years of good and

suitable service.

Tools required

The following hand tool will be needed for proper Installation of your new building:

12mm,14mm，and 17mm Open End Wrenches,

12mm, 14mm, 17mm Sockets or Box Wrench,

Large Flat Head Screwdriver,

2lb maul or Sledgehammer

4 Foot Level 14’ Step Ladder

Stake &String for aligning Base Plates &Frame

Assembly procedure

1. Prepare location and place all unit boxes near location sight. Perform an inventory

check before beginning, to be certain all components are available for installation.

2. Secure base plate flanges to base surface.

3. Assemble every group of arch.

4. Begin frame assembly with front end arch, first interior arch, purlins, etc.

5. Add to assemble other groups of arches.

6. Install main cover over frame.

7. Install end cover over end panels.

Read all the detailed instructions and notices in the following assembly

instructions!

Maintenance and care

Annually or more often, the unit should be completely inspected internally and externally to make

certain the unit remains properly installed and secured .Particular attention should be paid to:

Hardware-check all carriage bolts and hardware connectors to be certain they are in place and

tightened.

Weather trends, the unit will strain against the base plate flange under windy conditions, pegs

hardware, connection to frame members should be maintained tight and depth of pegs should be

checked to be certain they remain deeply and firmly set.

Snow Accumulation -All snow accumulation on the main cover should be removed as soon as

possible. Tap the main cover from the inside with a broom or soft brush to clear cover.

Main Cover Lacing-the poly rope that secures the main cover to the bottom rail of the frame

assembly should be checked, and adjusted as needed. The tension on the main cover should be

uniform from end and side to side. Rope ends must be tied off onto the frame members at the ends

on each side.

Cleaning -cover and doors can be cleaned with a mixture of light detergent and water. A soft

bristle brush with the mixture can be used to loosen any hard dirt, mold, or buildup on the cover.

After cleansing, the cover should be rinsed thoroughly to avoid any chemical reaction from

residual detergent. Allowing dirt and debris to sit on cover over an extended time will damage

cover irreparably.

Severe Weather-in preparation for inclement weather, completely secure the door of your buildings

portable building. Allowing wind to enter end lifts the

Thanks again for choosing this quality product. The following is the

detailed assembly instructions for you starting the assembly.

5,5x15x4,1x5,3 part list

Part code Description Qty

1 Curved roof tube

01ebutfooredisdevruC2

2A Curved side roof tube in front and back

panel

01sebuTllawediS3

3A Sidewall Tube of front and back panel

3B Sidewall Tube at right of front and back

panel to connect the winch rail

4 Horizontal wall and roof purlin 30

5L Base flange in corner 2

5R Base flange in corner 2

6L Base flange for sidewall 5

6R Base flange for sidewall 5

7 Base flange of door frame

8 Beam beside door frame

9 Door beam 2sets

10 Upper door track 4

11 Lower door track 2

26-09-2014-QJ

11A Lower door track for bottom rail 2

12 Bottom rail for winch of mechanical

door(beside the door)

13 Cover Tensioning tube for roof cover

2sets

14 Door dropping tube 12sets

15 Door dropping tube at the bottom 2sets

16 Cover tensioning tube of front and back

cover

17 Wind Brace Support 4

17A The tube clip for wind brace support 8

18 Hexagon bolt M10x90 100

19 Carriage bolt M10x100 40

8103x01MtlobnogaxeH02

21 Hexagon bolt M10x75 40

21A Hexagon bolt M10x85 22

22 Hexagon bolt M10x12 28

23 Tie down ratchet 14

24 Band for tie down ratchet 14

25 Roof cover

26 Side cover beside the door(without

window for the winch of door)

26-09-2014-QJ

27 Top cover above the door

28 Door cover 2

29 Single and Double Pulley

2sets

30 Winch

31 Rope for fastening the roof cover, the

door cover and the front&back cover

40 Stake peg 50

42 Plastic cap of tensioning tube 12

43 Turnbuckle and steel wire

8sets

26-09-2014-QJ

Figure 1

Sketch of Model 185017 Size: W5.5*L15*H5.3M

Figure 2 Sketch of parts

Step #1 --SECURING BASE FLANGES

Sit the building boxes in the chosen location. Remove all the components from

packaging to ensure all components are present by checking with the Part List.

Figure 3 Position of Base Flanges

Begin by determining exact location of the four (4) corners of the building. Mark front

edge and side-to-side width of assembly on ground. Drive alignment stakes into the

ground outside of the markings, and draw alignment strings along both ends and sides

of the building to the dimensions shown in Figure 3. The outline of the strings will

represent the final location of the base flanges. The initial location of each Corner

Base Flanges (5R & 5L) is critical to the alignment and fit of the frame components

and cover.

Locate the Left Corner Base Flange and Right Corner Base Flange(5R&5L). Secure

the base flanges with Stake Pegs (Part #17). Measurements shown in Figure 2 are to

the center of the upright sockets on each Base Flange.

The Shelter must be secured to a firm surface that can receive and retain augers and

pegs firmly in position. The shelter should be installed on FIRM GROUND, not on

SWAMP, SOFT/WET GROUND. The Base Flanges must be secured so they cannot

be moved. Arches are tensioned at their base as they insert into the Base Plate sockets.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Carpa de Dancover

Dancover

Dancover SEMI PRO 7x7m Manual de usuario

Dancover

Dancover ST145080 Manual de usuario

Dancover

Dancover Tentzing Explorer Series Manual de usuario

Dancover

Dancover 2,4m Series Manual de usuario

Dancover

Dancover CA119071 Manual de usuario

Dancover

Dancover Storage tent PRO 3,6m Series Manual de usuario

Dancover

Dancover TentZing CT168040 Manual de usuario

Dancover

Dancover AC153200 Manual de usuario

Dancover

Dancover CombiTent SEMI PRO AC18026 Manual de usuario

Dancover

Dancover TentZing CT168200 Manual de usuario

Dancover

Dancover PRO EventZone 9m Series Manual de usuario

Dancover

Dancover CombiTent SEMI PRO 6m Series Manual de usuario

Dancover

Dancover Pagoda Tent PRO+ 10x10m EventZone Manual de usuario

Dancover

Dancover CA119011 Manual de usuario

Dancover

Dancover Semi Pro XL 6m Series Manual de usuario

Dancover

Dancover PRO EventZone 9m Series Manual de usuario

Dancover

Dancover Proshed Garage Manual de usuario

Dancover

Dancover Semi PRO 4x8m Manual de usuario

Dancover

Dancover CombiTent PARTY TENT SEMI PRO Manual de usuario

Dancover

Dancover PRO XL Manual de usuario

Dancover

Dancover Pole Tent Semi PRO 6x6m Manual de usuario

Dancover

Dancover PARTY TENT SEMI PRO CombiTent 8m Series Manual de usuario

Dancover

Dancover ST01100 Manual de usuario

Dancover

Dancover Teepee Manual de usuario

Manuales populares de Carpa de otras marcas

OZTENT

OZTENT JV SIGNATURE EDITION Manual de usuario

GigaTent

GigaTent Summer Chalet Mini Tent Manual de usuario

Coleman

Coleman 2000007827 Manual

ShelterLogic

ShelterLogic 107153 Manual de usuario

Outsunny

Outsunny 84C-230 Manual de usuario

Napier

Napier SPORTZ COVE 61 Series Manual de usuario

EuroTrail

EuroTrail ATLANTIS PRO Manual de usuario

Reimo

Reimo Marina Manual de usuario

TiiTENT

TiiTENT TB300 Manual de usuario

Coleman

Coleman 2000033134 Guía de instalación

Ozark Trail

Ozark Trail W784.1 Guía de inicio rápido

SlingFin

SlingFin CrossBow 2 Manual de usuario

Coleman

Coleman 9600-141 Manual de usuario

Palram

Palram Arizona 5000 Wave - WINGS Manual de usuario

COVERPRO

COVERPRO 56184 Instrucciones de montaje

Vango

Vango Zenith 100 Manual de usuario

Costway

Costway PATIOJOY OP70818 Manual de usuario

Clarke

Clarke PUC 88 Manual de usuario