CYP EL-5600 Manual de usuario
EL-5600
Multi Format Presentation Switch (including SDI)
OPERATION MANUAL
3
DISCLAIMERS
The information in this manual has been carefully checked and is
believed to be accurate. CYP (UK) Ltd assumes no responsibility for any
infringements of patents or other rights of third parties which may result
from its use.
CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be
contained in this document. CYP (UK) Ltd also makes no commitment to
update or to keep current the information contained in this document.
CYP (UK) Ltd reserves the right to make improvements to this document
and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed,
stored in a retrieval system, or any of its part translated into any language
or computer le, in any form or by any means—electronic, mechanical,
magnetic, optical, chemical, manual, or otherwise—without express
written permission and consent from CYP (UK) Ltd.
© Copyright 2011 by CYP (UK) Ltd.
All Rights Reserved.
Version 1.1 August 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
4
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate
this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts inside
the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if
it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sucient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE SUMMARY OF CHANGE
v1.00 29/07/2013 First release
v1.01 06/07/2013 Corrections
5
CONTENTS
1. Introduction...........................................6
2. Applications ...........................................6
3. Package Contents ..................................6
4. System Requirements ...........................6
5. Features..................................................7
6. Operation Controls and Functions .......8
6.1 Front Panel................................................... 8
6.2 Rear Panel..................................................... 9
6.3 Remote Control........................................10
6.4 RS-232 Protocols......................................11
6.5 RS-232 Commands..................................12
6.6 OSD MENU .................................................14
7. Connection and Installation .............. 16
8. Specications...................................... 17
8.1 Technical Specications ........................17
8.2 Supported Input/Output Resolution .......18
9. Acronyms............................................. 20
6
1. INTRODUCTION
The EL-5600 presentation switch is an advanced HDMI, PC, SDI,
Composite, S-Video and Component switcher/scaler. This device can
scale and switch input sources and display them via the HDMI and VGA/
HD outputs simultaneously with their associated audio signals at a wide
range of output resolutions (up to 1080p or WUXGA reduced blanking).
Audio can be de-embedded from HDMI and SDI input sources using the
built-in Digital to Analogue audio converter (DAC), whilst analogue audio
can also be converted to digital for ultimate exibility in audio signal
management. In addition, there is an SDI Loop Out for monitoring or
extending the SDI input signal. Control is via the IR remote, RS-232, or via
front panel buttons and includes an on-screen menu providing settings
and system information.
2. APPLICATIONS
Digital and analogue signal convergence
Convert analogue video/audio signals for use with digital displays
Integrate multiple sources and signal types to a single display in a
Meeting room or Conference hall environment
3. PACKAGE CONTENTS
EL-5600 Multi format switch
Remote Control (CR-117)
15-pin D-Sub to 3 RCA adaptor cable
Power Adaptor
Operation Manual
4. SYSTEM REQUIREMENTS
Source equipment such as Blu-ray players or SDI camera, VGA or HDMI
display and amplier/active speakers with connection cables.
7
5. FEATURES
Supports HDMI, Composite Video, S-Video, PC (VGA)/HD (Component)
and SDI inputs
Supports HDMI and VGA/Component (with adaptor) outputs
Supports SDI loop-through output
Supports analogue stereo, optical and coaxial digital inputs and
optical digital output, analogue stereo output or embedding to HDMI
output
Supports conversion of multiple video formats and audio input to
HDMI or PC/HD and analogue stereo outputs
Supports EDID and HDCP
Supports 3D de-interlacing, noise reduction and 3D comb lter
Supports frame rate conversion
Supports RS-232, IR remote control, and front panel control
Supports SDI Standards of SMPTE 425M (Level A and Level B), SMPTE
424M, SMPTE 292M, SMPTE 259M-C
Supports SDI bit rates at 2.970 Gb/s, 2.970/1.001 Gb/s, 1.485 Gb/s,
1.485/1.001 Gb/s and 270 Mb/s
Supports SDI signal input and output distances of up to 300m for SD
signals, 200m for HD signals and 100m for 3G signals
Supports SDI Auto video mode detection (3G/SD/HD)
Video functions: Aspect Ratio Adjustment / Video Noise Reduction /
Underscan & Overscan Selection / De-Interlacing
Note: SDI cable operating distance tested with belden 1694A cable. Operating
distances may vary for cables of dierent specications.
8
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
TUPNIREWOP PMOCVSVCRI RETNEUNEMIDS2IMDH1IMDHCP
-
+
CSLUX-300I DIGITAL VIDEO SCALER
XGA
720P
1 2 4 63 5
1POWER & POWER LED: Press this button to switch the device on or
to set it to standby mode. Once the device is connected to an active
power supply the LED will illuminate and the device will switch on
automatically.
2IR Receiver window: Receives only the IR signal from the remote
control included in the package.
3INPUT button and LEDs: Press this button repeatedly to cycle
through the input sources sequentially. An LED on the front panel will
illuminate to indicate the selected input source.
4MENU: Press this button to enter the OSD menu.
5−/+: Press these buttons to navigate up and down in the OSD menu.
6ENTER: Press this button to conrm the selection in the OSD menu.
Press this button simultaneously with the '+' (plus) button to instantly
switch the output to XGA resolution or with the '−' (minus) button to
instantly switch the output to 720p resolution.
9
6.2 Rear Panel
DC 5V
2ECIVRES1ECIVRES
OPTICAL OPTICAL
RS232
L/R L/R
Cr/Pr Cb/Pb Y SV
R L
R L
R LCV
HDMI HDMI 1 HDMI 2
PC/HD PC
SDI
LOOP OUTPUT SDI
OUTPUT INPUT
1 63
2 4 5 7
1OUTPUT:
L/R: Connect to an amplier or active speakers for audio output in
stereo format.
HDMI: Connect to an HDMI display or amplier for video and/or audio
output.
OPTICAL: Connect to an amplier or active speakers for audio output
in digital format.
PC/HD: Connect to a monitor/display for video output. For HD
(Component) output,use the supplied D-Sub 9pin to 3 RCA adaptor
cable for HD resolutions from 480p~1080p.
2SERVICE 1: Reserved for manufacturer use only.
3SDI LOOP OUTPUT: Connect to an SDI display for monitoring of the
SDI input signal or an SDI extender for extending the SDI signal to
further areas.
4RS-232: Connect to a PC/Laptop to use RS-232 commands to control
the device (See Section 6.5 for details on RS-232 commands).
5SERVICE 2: Reserved for manufacturer use only.
6INPUT:
SDI: Connect to an SDI camera or other SDI source for both video and
audio signal conversion.
HDMI 1: Connect to an HDMI source such as Blu-ray/DVD player for
both video and audio signal conversion.
HDMI 2: Connect to an HDMI source such as Blu-ray/DVD player for
both video and audio signal conversion.
10
L/R: Connect to source's L/R output with 3.5mm mini-jack for audio
signal conversion.
PC/HD: Connect to a PC/Laptop source for video signal input with a
D-Sub 15pin cable.
OPTICAL: Connect to a source's optical output for audio signal
conversion.
YCbCr/HDPbPr + L/R: Connect to source equipment such as a DVD
player for both video and audio signal conversion.
CV + L/R: Connect to a composite video source such as video/DVD
player for both video and audio signal conversion.
SV + L/R: Connect to an S-Video source such as a video/DVD player for
both video and audio signal conversion.
7DC 5V: Plug the 5V DC power supply into the unit and connect the
adaptor to an AC outlet.
6.3 Remote Control
1INPUT: Press this button repeatedly
to cycle through the input sources
sequentially. An LED on the front panel
will illuminate to indicate the selected
input source.
2POWER: Press this button to switch the
device on or to set it to standby mode.
3CV/SV/COMP/PC/HDMI1/HDMI2/SDI:
Direct source selection keys. Press one
of these keys to switch to the selected
source.
4EXIT: Press this button to exit the menu or
the current selection in the OSD menu.
5MENU: Press this button to enter the OSD
menu.
6RESET: Press this button to reset the
device back into the default settings.
CR-117
POWERINPUT
PC HDMI 1 HDMI 2
SDI
EXIT MENU
OK
RESET AUTO
ADJUST
1
4
6
2
5
7
8
3
SVCV COMP
Tabla de contenidos
Otros manuales de Cambiar de CYP
CYP
CYP CMLUX-88S Manual de usuario
CYP
CYP CLUX-42S Manual de usuario
CYP
CYP EL-5500 Manual de usuario
CYP
CYP PU-8H8HBT Manual de usuario
CYP
CYP EL-41SY Manual de usuario
CYP
CYP CSDI-44 Manual de usuario
CYP
CYP CMLUX-4H4CAT Manual de usuario
CYP
CYP CPLUS-31PS Manual de usuario
CYP
CYP EL-8100V Manual de usuario
CYP
CYP MED-AS60 Manual de usuario
CYP
CYP CLUX-4S2 Manual de usuario
CYP
CYP EL-21SY Manual de usuario
CYP
CYP EL-21SY Manual de usuario
CYP
CYP EL-42HEAC Manual de usuario
CYP
CYP EL-C41C Manual de usuario
CYP
CYP EL-41AT Manual de usuario
CYP
CYP EL-5500-HBT Manual de usuario
CYP
CYP CPLUS-V4H1HP Manual de usuario
CYP
CYP CH-2537TXM-TB Manual de usuario
CYP
CYP CLUX-42SA Manual de usuario
