CYP CPLUS-V4H1HP Manual de usuario
CPLUS-V4H1HP
4K UHD+ 4×1 HDMI Switcher
with IP Control
Operation Manual
Operation Manual
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means—
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise—without express written permission and consent from
Cypress Technology.
© Copyright 2017 by Cypress Technology.
All Rights Reserved.
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE (DD/MM/YY) SUMMARY OF CHANGE
RDV1 17/04/16 Preliminary release
VS0 04/07/17 Updated text/diagrams
CONTENTS
1. Introduction......................................................1
2. Applications.....................................................1
3. Package Contents ..........................................1
4. System Requirements......................................1
5. Features............................................................2
6. Operation Controls and Functions.................2
6.1 Front Panel ................................................. 2
6.2 Rear Panel.................................................. 3
6.3 Remote Control......................................... 3
6.4 IR Cable Pin Assignments ......................... 4
6.5 RS-232 Protocol.......................................... 4
6.6 RS-232 and Telnet Commands ................ 5
6.7 Telnet Control ............................................ 8
6.8 WebGUI Control ........................................ 9
6.8.1 Device Discovery APP ..................... 9
6.8.2 WebGUI Control Page .................. 10
7. Connection Diagram ....................................14
8. Specications ................................................15
8.1 Technical Specications ........................ 15
8.2 Video Specications............................... 16
9. Acronyms .......................................................17
1
1. INTRODUCTION
This 4×1 HDMI switcher is the most advanced HDMI solution for true
Ultra High-Denition signal routing. This unit allows for the switching
of any of four 18Gbps HDMI input signals to a single 18Gbps HDMI
display device. Resolutions up to 4096×2160@60Hz (4:4:4), 16-bit
Deep Color, HDR (High Dynamic Range), HD audio as well as other
features dened by the HDMI 2.0 specication are supported. Multiple
control interfaces are available including RS-232, Ethernet (WebGUI &
Telnet), IR remote and front-panel buttons making operation easy and
intuitive.
2. APPLICATIONS
• Entertainment Rooms & Home Theaters
• Showrooms & Demo Rooms
• Lecture Room & Hall Presentations
• Public Commercial Displays
3. PACKAGE CONTENTS
• 1×4 by 1 HDMI Switcher
• 1×Remote Control (CR-72)
• 1×IR Extender Cable
• 1×5V/2.6A DC Power Adaptor
• 1×Operation Manual
4. SYSTEM REQUIREMENTS
• HDMI source equipment such as media players, video game
consoles or set-top boxes.
• HDMI receiving equipment such as HDTVs, monitors or audio
ampliers.
2
5. FEATURES
• HDMI 2.0 with 18Gbps 4K UHD support, single-link DVI 1.0 compliant
• HDCP 2.2 and 1.4 compliant
• 4 HDMI inputs and 1 HDMI output
• Supports HDTV resolutions up to 4K UHD (3840×2160@50/60Hz &
4096×2160@50/60Hz)
• Supports data rates up to 18Gbps and Deep Color (16-bit) up to
1080p
• Supports pass-through of LPCM 7.1, Bitstream and HD Bitstream
audio formats
• Remotely controllable via Ethernet (WebGUI & Telnet), RS-232 and
IR remote
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
HDCP2.2
+
POWER SYNC
UHD 4 TO 1 SWITCHER
INPUT 1234
1 2 53 4 6
1IR WINDOW: Accepts IR signals from the included IR remote for
control of this unit only.
2POWER: Press this button to power on the unit or place it into stand-
by mode.
Note: Ethernet and RS-232 remain active while the unit is in stand-
by mode.
3POWER LED: The LED will illuminate RED to indicate the unit is
receiving power but is in stand-by mode. It will illuminate GREEN to
indicate that the unit has been turned on.
4SYNC LED: This LED will illuminate GREEN when a stable connection
with an output device is detected.
3
5INPUT: Press this button to sequentially switch through the 4
available inputs.
6INPUT LED 1~4: These LEDs will illuminate GREEN to indicate which
of the 4 sources are currently selected.
6.2 Rear Panel
1234
HDMI IN HDMI OUT SERVICE CONTROL RS-232 IR IN DC 5V
21 3 4 5 6 7
1HDMI IN 1~4: Connect to HDMI source equipment such as a media
player, game console or set-top box. DVI source equipment may
be connected by using an HDMI to DVI adapter.
2HDMI OUT: Connect to HDMI TVs, monitors or ampliers for
digital video and audio output. DVI display equipment may be
connected by using an HDMI to DVI adapter.
3SERVICE: This slot (USB 2.0) is reserved for rmware update use only.
4CONTROL: Connect directly, or through a network switch, to your
PC/laptop to control the unit via Telnet/WebGUI.
5RS-232: Connect directly to your PC/laptop to send RS-232
commands to control the unit.
6IR IN: Connect to the provided IR Extender to extend the IR control
range of the unit. Ensure that the remote being used is within direct
line-of-sight of the IR Extender.
7DC 5V: Plug the 5V DC power adapter into the unit and connect it
to an AC wall outlet for power.
6.3 Remote Control
1POWER: Press this button to power on the unit or place
it into stand-by mode.
2INPUT 1~4: Press 1 through 4 to select the input source. CR-72
POWER
INPUT
34
12
1
2
4
6.4 IR Cable Pin Assignments
3
1
2
IR Signal
Power
Ground
IR Extender
6.5 RS-232 Protocol
UNIT
►
◄
REMOTE SYSTEM
Pin Denition Pin Denition
1 NC 1 NC
2TxD 2RxD
3RxD 3TxD
4 NC 4 NC
5 GND 5 GND
6 NC 6 NC
7 NC 7 NC
8 NC 8 NC
9 NC 9 NC
Baud Rates: 115200bps
Data Bits: 8
Parity Bits: None
Stop Bit: 1
Flow Control: None
5
6.6 RS-232 and Telnet Commands
COMMAND DESCRIPTION AND PARAMETERS
HELP Displays all available commands.
?Displays all available commands.
P0 Turn unit’s power off. (Stand-by mode)
P1 Turn unit’s power on.
INNAME N1 N2 Set the name of input N1 to N2.
N1 = 1~4 [Input number]
N2 = {name} [8 characters max]
INNAME N1 Show the input name of N1.
N1 = 1~4 [Input number]
INNAME Show the names of all inputs.
OUTNAME N1 Set the output name to N1.
N1 = {name} [8 characters max]
OUTNAME Show the current output name.
OUT N1 Set the input to be routed to the output.
N1 = 1~4 [Input number]
OUT Show the current input routing.
SOURCEDET Show all source information.
SINKINFO Show all sink information.
HDCPIN N1 N2 Set the HDCP mode for input N1.
N1 = 1~4 [Input number]
Available values for N2:
0 [Standard]
1 [Apple Mode]
HDCPIN N1 Show the HDCP settings for input N1.
N1 = 1~4 [Input number]
HDCPIN Show all current HDCP input settings.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Cambiar de CYP
CYP
CYP OR-HD62CD-4K22 Manual de usuario
CYP
CYP EL-5300 Manual de usuario
CYP
CYP EL-41WAD Manual de usuario
CYP
CYP EL-42HEAC Manual de usuario
CYP
CYP EL-41SY Manual de usuario
CYP
CYP CH-1539TXPLPD Manual de usuario
CYP
CYP DT-21 Manual de usuario
CYP
CYP CH-2537TXM-TB Manual de usuario
CYP
CYP CH-2537TXWPUS Manual de instalación
CYP
CYP EL-41PIP Manual de instalación
CYP
CYP CDPS-U42HPIP Manual de instalación
CYP
CYP EL-31TT-4K22 Manual de usuario
CYP
CYP EL-41S-4K22 Manual de usuario
CYP
CYP EL-5400 Manual de usuario
CYP
CYP EL-5500-HBT Manual de usuario
CYP
CYP EL-42S Manual de usuario
CYP
CYP EL-41AT Manual de usuario
CYP
CYP CPRO-3D41GAME Manual de usuario
CYP
CYP CFSW-51MHL Manual de usuario
CYP
CYP CDPS-41SQ Manual de usuario
