CYP EL-C41C Manual de usuario
EL-C41C
4 by 1 HDMI V1.3
Switcher with CEC
Operation Manual
EL-C41C
Trademark Acknowledgments
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
Safety Precautions
Please read all instructions before attempting to unpack or install or
operate this equipment, and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
Always follow basic safety precautions to reduce the risk of
re, electrical shock and injury to persons.
To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
Never spill liquid of any kind on or into this product.
Never push an object of any kind into this product through
module openings or empty slots, as you may damage parts.
Do not attach the power supply cabling to building surfaces.
Do not allow anything to rest on the power cabling or allow it to
be abused by persons walking on it.
To protect the equipment from overheating, do not block the
slots and openings in the module housing that provide
ventilation.
Version No Date Summary of Change
V1 20090717 Preliminary Release
Revision History
Table of Contents
1
1
1
1
2
3
3
4
5
5
5
6
7
8
1. Introduction…………………………………………................................
2. Applications...........................……………………………………………
3. Package Contents............……………………………………………….
4. System Requirements....................………………………………….…..
5. Features.............................………………………………………………..
6. Installation............................…………………………………….………..
6.1 Front Panel...................……..………..............................…………..
6.2 Rear Panel....................……..………..............................…………..
7. Remote Control...................................................................................
8. RS-232 Protocol...................................................................................
8.1 Pin denition...................…...………..............................…………..
8.2 RS-232 Command..................………............................…………..
9. Connection and Installation..............................................................
10. Specications......................................................................................
1. Introduction
This is a high performance HDMI switcher which provides for various HDMI
sources to share one HDTV display with CEC control functions of auto-off and
auto-switch. It also support deep color and xvYCC with RS-232 control. Simply
press one button to select your desired HDMI source for display on the HDTV
or use remote control to control your sources in distant.
2. Applications
Multi-sources with one display.
Showroom display.
Educational presentation.
3. Package Contents
4 by 1 HDMI v1.3 switcher
Remote control (CR-63)
5V DC Power supply adaptor
Operation manual
4. System Requirements
Input source equipments, output displayer with HDMI cables.
1
5. Features
HDMI 1.3 and HDCP 1.1 compliant
Supports deep color display RGB/YCbCr 4:4:4 24/30/36 bits
Supports color space YCbCr 4:2:2 16/20/24 bits
Supports high denition audio – Dolby Digital True HD®and DTS-HD®
Signal Enhancement feature allows signal quality improvement after
long distance transmission
HDMI cable distance test with 1080p/8-bit resolution, the input/output
can reach up to 15/15 meters. If running at 1080p/12-bit, the input/
output can reach at up to 15/6 meters
PC resolution supports: VGA, SVGA, XGA, SXGA, and UXGA (1600 x 1200)
HD resolution supports: 480i ~1080p 50/60 and 1080p 24
With remote control function
Supports RS232 operation
Supports CEC control function
Supports xvYCC
2
6. Installation
6.1 Front Panel
① Remote control sensor.
② Input select indicators: Press the “INPUT”button repeatedly to switch to
your desired input source. The LED that illuminates indicate the
corresponding input source is selected.
③ CEC button indicator: When the LED illuminate it means CEC is ON. Press
again to switch CEC to bypass mode and the LED will not illuminate
which means the CEC function will be terminate.
Note: Both input source and output display must support CEC function for
the switcher to properly perform CEC.
④ POWER indicator: When power is connected to the device,
the device automatically turns on and the power LED will turn red.
Note: To turn ON or switch the device to standby mode, please press the
"POWER" button on the remote control unit.
1 2 3 4
EL-C41C
4x1 HDMI v1.3 Switcher with CEC
INPUT
CEC
ON/Bypass POWER
① ② ③ ④
3
6.2 Rear Panel
① HDMI OUT: This is the slot where you connect the HDMI output of the
switcher to the HDMI input of your display using a HDMI cable.
② RS-232 input: When doing rmware upgrade and/or PC remote system
control, connect a D-sub 9 pin cable from this RS232 slot to your
computer.
③ HDMI IN 1~4: These slots connect to the HDMI/DVI output ports of your
source equipments. ie, set- up-box, DVD or Blue Ray.
④ DC 5V: Connect the 5V DC power adaptor into this slot and plug the
adaptor to an AC wall outlet.
RS-232
DC 5V
OUTPUT
INPUT
4321
① ③ ④②
4
7. Remote Control
① . Power: Press the button to turn on the unit-or set
the device to standby mode.
② . CEC: Press the button to turn on /Bypass the CEC
function. When the LED illuminate it means CEC is ON
and both input source and output display must support
CEC function in order to perform CEC rightly. Press
again to switch CEC to Bypass mode and the LED will
not illuminate whic means the CEC function will be
terminate.
③ . Input selector: Press from 1~4 to select the desired input
sources. No. 5~8 is not functioning for this model.
8. RS-232 Protocol
8.1 Pin denition
Baud Rate: 19200 bps
Data Bit: 8 bits
Parity: None
Stop Bit: 1 bit
Flow Chart: None
CR-63
POWERCEC
INPUT
3 4
1 2
5 6
7 8
①
③
②
Switcher Remote Controller
PIN Denition PIN Denition
1 NC 1 NC
2 TxD 2 RxD
3 RxD 3 TxD
4 NC 4 NC
5 GND 5 GND
6 NC 6 NC
7 NC 7 NC
8 NC 8 NC
9 NC 9 NC
5
8.2 RS-232 Command
Notes:
1. The command is a combination of characters and digits.
2. This combination command code has to be separated by ASCII character
SPACE.
3. If the command is legal the unit will reply “OK”message .
4. If the command is illegal, the unit will prompt you with a “NG”message.
Command Code Function
“I”+ “1”PORT 1 ON
“I”+ “2”PORT 2 ON
“I”+ “3”PORT 3 ON
“I”+ “4”PORT 4 ON
“C”+ “1”CEC ON
“C”+ “0”CEC OFF
“P”+ “1”POWER ON
“P”+ “0”POWER OFF
“S”REPORT STATE
6
9. Connection and Installation
LCD TV
DVD1 DVD3
DVD2 STB
CR-63
POWERCEC
INPUT
3 4
1 2
5 6
7 8
30°
30°
3M 3M
7M
7
Tabla de contenidos
Otros manuales de Cambiar de CYP
CYP
CYP DT-21 Manual de usuario
CYP
CYP EL-21SY Manual de usuario
CYP
CYP EL-M31TT-4K22 Manual de usuario
CYP
CYP CFSW-51MHL Manual de usuario
CYP
CYP CLUX-41N Manual de usuario
CYP
CYP CPLUS-V3H1H Manual de usuario
CYP
CYP CSDI-44 Manual de usuario
CYP
CYP CLUX-41AP Manual de usuario
CYP
CYP PU-2H8HBTE-AD Manual de usuario
CYP
CYP PU-22HC Manual de usuario
CYP
CYP EL-42S Manual de usuario
CYP
CYP EL-5400D Manual de usuario
CYP
CYP EL-42S Manual de usuario
CYP
CYP EL-5500 Manual de usuario
CYP
CYP CPLUS-V4H1H Manual de usuario
CYP
CYP CSC-6030CVE Manual de usuario
CYP
CYP AU-D41 Manual de usuario
CYP
CYP EL-5500 Manual de usuario
CYP
CYP EL-42PIP Manual de usuario
CYP
CYP EL-7500V Manual de usuario
