CYP EL-42HEAC Manual de usuario
EL-42HEAC
4 Way HDMI Switcher with
2 Identical Outputs
(Including HEAC function)
OPERATION MANUAL
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
electrical shock and injury to persons.
moisture or install this product near water.
Never spill liquid of any kind on or into this product.
Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
Do not attach the power supply cabling to building surfaces.
Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
REVISION HISTORY
VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE
VS1 09/02/12 First Release
VR2 06/03/12 CEC function on output 1 only
CONTENTS
1. Introduction............................................ 1
2. Applications........................................... 1
3. Package Contents ................................ 1
4. System Requirements............................ 1
5. Features.................................................. 2
6. Operation Controls and Functions....... 3
6.1 Front Panel ........................................3
6.2 Rear Panel.........................................4
6.3 Remote Control................................5
6.4 RS232 Protocol and Command......6
7. Connection Diagram ............................ 7
........................................ 8
9. Acronyms ............................................... 9
1
1. INTRODUCTION
This is a high performance HDMI™ Switcher with four HDMI inputs &
two outputs HDMI™ Switcher, the output ports support Audio Return
Channel (ARC) from a compaitble ARC TV and HDMI Ethernet
The HDMI Switcher provides an S/PDIF link from the HDMI signal and
the sink.
The HEC feature adds a network connection to the HDMI link 100 Mbps
Ethernet connection. Using an HDMI with HEAC cable allows for the
convenient integration of internet capable HEAC Televisions into the
end user’s home network system.
2. APPLICATIONS
Simultaneously display a HDMI source on 2 TVs/displays
Connect internet capable devices through HEC to network routers/
modems
Connect network attached media streaming devices to
compatible HEAC TV
Showroom displays
Educational demonsrations
Commercial usage
3. PACKAGE CONTENTS
4 × 2 HDMI Switcher with HEAC
5 V/2.6 A DC power supply adaptor
Operation Manual
4. SYSTEM REQUIREMENTS
Source equipment with HDMI output connector(s)
Displays TV with HDMI HEAC input connector(s)
2
5. FEATURES
Two output ports supporting Ethernet Channel (HEC) and Audio
HDMI v1.4 supports:
Audio Return Channel (ARC)
3D
networking at up to 100 Mb/sec
EDID optiions include Standard, TV or Lock EDID feature
Supports CEC bypass on HDMI OUT 1
Audio support:
HDMI 1.4 compatible audio interface
S/PDIF pass through
3
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
INPUT TVSTD LOCK POWEREDID
3D2CH 4321
BITSTREAM
LPCM 5.1/7.1
1 52 3 4
1IR Remote Control Sensor
2Audio/3D Content Indicator
The system will automatically detect incoming audio/video signal
type and the green LEDs will illuminate accordingly.
3Input Selection
Press input button to select input source, the Blue LED will illuminate
accordingly. If none of the LEDs are illuminated then no input
has been selected, this is to allow the device to access the ARC
feature alone.
4EDID Selection
The EDID control button selects
between using the EDID from the
display attached to Output 1/TV or
using the onboard EDID/STD (the
Green LED will illuminate accordingly).
When the EDID button is pressed for
longer then 3 seconds, the RED LED will
illuminate to indicate that the EDID is already locked to STD or TV
EDID as you selected accordingly. When EDID is set on STD audio
will support PCM 2CH, video modes supported are listed in the
table above.
5Power Button
Press this button to switch on the device or press it again to set it to
standby mode.
81012
RGB 999
Y444 988
Y422 9
XvYCC 988
4
6.2 Rear Panel
DC 5V
HDMI IN
12
RS-232
HDMI OUT
1212 1234
ETHERNET
SPDIF/ARC
OUT
1 2 3 4
1RS-232
to Section 6.4.
2HDMI OUT 1~2/ARC 1~2/ETHERNET 1~2
HDMI/HEAC equipped TVs or displays will pass the Ethernet and
Audio signals via HDMI v1.4 cable back to the HDMI Output port,
the splitter will separate the Ethernet and audio, and will output
DVD player, audio content can be sent “upstream” from the TV
The HDMI Switcher can use the HDMI Ethernet Channel (HEC) to
consolidate video, audio and data streams into a single HDMI
cable connection to an Ethernet Hub/modem in order to access
the internet and also incorporates a dedicated data channel
at up to 100 Mb to control and search from the sink (please see
Section 6 for connection diagram). The HDMI output number is
correspondingto ARC and Ethernet output number.
Note 1: Be sure to connect devices with a suitable HDMI cable
designed to support the Ethernet Channel functionality, either the
standard HDMI cable with Ethernet or High Speed HDMI cable with
Ethernet.
5
Note 2: When the HDMI output has both Audio and ARC at the
same time the ARC will be the prioritized.
3HDMI INPUT 1~4
Connect to HDMI or DVI sources equipment such as DVD player or
Note A: This system was tested with 24 AWG cables. If using cables
Note B:!"
LED UA40B700 12-bit LCD TV.
Note C: Figures provided in this manual are for reference only,
!"!"!#!
and display being used along with the type of cables and their
4Power
Plug the DC 5 V power supply into the unit and connect the
adaptor to an AC wall outlet.
6.3 Remote Control
1Power button
Press to switch On the device, press it again to
set the device in standby mode.
2INPUT 1~4
Press the desire input button to select the input
source.
2
1
6
6.4 RS232 Protocol and Command
CPRO-3D42S
Remote Control Console
PIN PIN
1NC 1NC
2 2
3 3
4NC 4NC
5 GND 5 GND
6NC 6NC
7NC 7NC
8NC 8NC
9NC 9NC
Baud Rate: 9600 bps
Parity: None
Flow Control: None
Command Action
POWER 00 Power Off (standby)
POWER 01 Power On
PORT 11 Output Select Input 1
PORT 12 Output Select Input 2
PORT 13 Output Select Input 3
PORT 14 Output Select Input 4
PORT 00 No Input Selection (for ARC)
7
7. CONNECTION DIAGRAM
DC 5V
HDMI IN
12
RS-232
HDMI OUT
1212 1234
ETHERNET
SPDIF/ARC
OUT
12
RS-232
HDMI OUT
12 1 2 1
ETHERNET
SPDIF/ARC
OUT
Blu-ray Player DVD Player
Speakers
AV Amplifier
Notebook
PC
Speakers
Internet
Modem
Blu-ray Player DVD Player
Hub/
Router
TV/Monitor
without ARC
TV/Monitor
with ARC
& HEC
Blu-ray Player
with HEC
ARC
HEC
HEC
Audio Loop Out
Audio Loop Out
ARC
Note: In this example,
HDMI In 1 is selected.
EL-42HEAC
Otros manuales para EL-42HEAC
1
Tabla de contenidos
Otros manuales de Cambiar de CYP
CYP
CYP EL-42S Manual de usuario
CYP
CYP CLUX-21N Manual de usuario
CYP
CYP MED-AS60 Manual de usuario
CYP
CYP AU-D41 Manual de usuario
CYP
CYP CPLUS-V4H1H Manual de usuario
CYP
CYP EL-42S Manual de usuario
CYP
CYP CLUX-31GAME Manual de usuario
CYP
CYP EL-C81C Manual de usuario
CYP
CYP CP-290 Manual de usuario
CYP
CYP DT-21 Manual de usuario
CYP
CYP PU-22HC Manual de usuario
CYP
CYP EL-41WX Manual de usuario
CYP
CYP DCT-17 Manual de usuario
CYP
CYP EL-5500 Manual de usuario
CYP
CYP EL-42SA Manual de usuario
CYP
CYP CPLUS-31PS Manual de usuario
CYP
CYP CLUX-42S Manual de usuario
CYP
CYP EL-C41C Manual de usuario
CYP
CYP CPLUS-V3H1H-TB Manual de usuario
CYP
CYP CDPS-41SQ Manual de usuario
