CYP PU-44XL-KIT Manual de usuario

PU-44XL-KIT

Express Installation Kit - 4 x 4 HDBaseT™ LITE Matrix

with PU-514L-RX Receivers

OPERATION MANUAL

DISCLAIMERS

The information in this manual has been carefully checked and is

believed to be accurate. CYP (UK) Ltd assumes no responsibility for any

infringements of patents or other rights of third parties which may result

from its use.

CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be

contained in this document. CYP (UK) Ltd also makes no commitment to

update or to keep current the information contained in this document.

CYP (UK) Ltd reserves the right to make improvements to this document

and/or product at any time and without notice.

No part of this document may be reproduced, transmitted, transcribed,

stored in a retrieval system, or any of its part translated into any language

or computer le, in any form or by any means—electronic, mechanical,

magnetic, optical, chemical, manual, or otherwise—without express

written permission and consent from CYP (UK) Ltd.

Version 1.1 August 2011

TRADEMARK ACKNOWLEDGMENTS

All products or service names mentioned in this document may be

trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or operate

this equipment and before connecting the power supply.

Please keep the following in mind as you unpack and install this

equipment:

• Always follow basic safety precautions to reduce the risk of re,

electrical shock and injury to persons.

• To prevent re or shock hazard, do not expose the unit to rain,

moisture or install this product near water.

• Never spill liquid of any kind on or into this product.

• Never push an object of any kind into this product through any

openings or empty slots in the unit, as you may damage parts inside

the unit.

• Do not attach the power supply cabling to building surfaces.

• Use only the supplied power supply unit (PSU). Do not use the PSU if

it is damaged.

• Do not allow anything to rest on the power cabling or allow any

weight to be placed upon it or any person walk on it.

• To protect the unit from overheating, do not block any vents or

openings in the unit housing that provide ventilation and allow for

sucient space for air to circulate around the unit.

REVISION HISTORY

VERSION NO. DATE SUMMARY OF CHANGE

v1.00 28/05/13 First release

v1.01 30/05/13 Corrections

v1.02 31/07/13 Added USB Power Cable information

v1.03 16/08/13 Corrected package contents

CONTENTS

1. Introduction...........................................6

2. Applications ...........................................6

3. Package Contents ..................................6

4. System Requirements ...........................7

5. Features..................................................7

6. Operation Controls and Functions .......8

6.1 Front Panel................................................... 8

6.2 Rear Panel..................................................... 9

6.3 Side Panel...................................................10

6.4 Remote Control........................................10

6.5 IR Pin Assignment....................................11

6.6 RS-232 Pin Assignment..........................11

6.7 RS-232 & Telnet Commands.................12

6.8 Telnet Control............................................13

6.9 Web GUI Control ......................................15

7. Connection Diagram .......................... 17

8. Specications...................................... 18

9. Acronyms............................................. 19

1. INTRODUCTION

This 4 by 4 HDMI HDBaseT™ Lite Matrix Express Installation Kit has been

developed as a robust and cost eective solution at the heart of any four

zone multi-room environment. Supplied complete with a HDBaseT™ Lite

Matrix plus four PU-514L-RX receivers, the kit enables an installer to easily

and condently congure a 4-zone multi-room AV system using HDBaseT

Lite technology and distribute content throughout the system over a

Single CAT5e/6/7 cable infrastructure.

The Express Install Kit supports the transmission of video (resolutions

up to 1080p Full HD and 1920x1200@60Hz), multi-channel digital audio,

and control via IR, RS-232, or Web GUI/Telnet IP, from four high denition

sources to four HDBaseT outputs over a single CAT5e/6/7 cable (up to

60m) for each output.

The PU-44XL-KIT is supplied with 4x PU-514L-RX receivers which utilise

the 2-way IR control capabilities of the matrix. Utilise the USB power

output from a TV as an optional way of powering the PU-514L-RX receiver

unit alternative to a mains power supply.

Use the IP control feature to enable users to access and control the matrix

remotely and also allow additional options for integration of third-party

control systems. CYP provide control drivers for control systems such

as Control 4, RTI, Crestron, AMX, Control FX, and Demopad. These are

available at no extra cost.

2. APPLICATIONS

Domestic HDMI Matrix system

Video/TV wall display and control

Security surveillance and control

Commercial advertising, display and control

University Lecture hall display and control

Retail Sales and demonstration

3. PACKAGE CONTENTS

4×4 HDMI HDBaseT Lite Matrix over 4 CAT5e/6/7

4× PU-514L-RX Receivers

4×IR Extender

4×IR Blaster

1×24V/2.7A DC adaptor

1×Remote control

1×Set Rack Ears (REARS-10)

Operation manual

4. SYSTEM REQUIREMENTS

HDMI equipped source devices, connect with HDMI cables or DVI

equipped source, connect with DVI to HDMI cables

HDMI equipped displays (TVs or monitors) or HDMI equipped AV

receivers, connect with HDMI cables

Industry standard CAT5e/6/7 cables

5. FEATURES

Supports all v1.3 HDMI resolutions

Supports uncompressed video/audio up to 10.2Gbps

Common supported resolutions: HDTV: 480p, 576p, 720p, 1080i,

1080p, 1080p24; PC: VGA, SVGA, XGA, WXGA, SXGA, UXGA, WUXGA.

HDMI, HDCP and DVI complaint

High Denition Audio supported: Dolby TrueHD, Dolby Digital Plus

and DTS-HD Master Audio plus LPCM (up to 192kHz)

Uncompressed data transfer over single CAT cable (60m - CAT5e/6/7)

Supports third-party control systems, with drivers available for: Control

FX, AMX, Crestron, RTI, Control 4

Supports HDMI input up to 15m 1080p 8bit or 10m 1080p 12bit.

Supports RS-232, 2-Way IR, Manual Selection Buttons, and HDMI CEC

control pass through

Selectable EDID settings - TV (downstream) and STD (xed)

Compact 1U Rack mount design

Supports 3D signals

Supports additional IR Control via a master (ALL) Input/Output

Supports full IP control

Supplied with 4x PU-514L-RX receivers

Choose to power the PU-514L-RX via the USB output from a TV (Cable

available separately - APC-USB): * Please note the performance and

consistency of USB power outputs from TV's can vary and cannot be

guaranteed by CYP.

Note:

1. Do not connect the CONTROL port to the CAT outputs of this device.

6. OPERATION CONTROLS AND FUNCTIONS

6.1 Front Panel

OUT

C4D

POWERLOCK MENU

61 2 3 4 5

1LCM : Displays the setting information of each input and output

setting.

2IR: IR Receiver window (accepts the remote control signal of this

device only).

3POWER: Press this button to power the device on/o. The LED will

illuminate green when the power is on, red when it is in 'Standby'

mode.

4LOCK: Press this button to lock all the buttons on the panel; press

again to unlock. The LED will illuminate when locked.

5Menu: Press once to select EDID setting from STD (internal) 1 or TV

(external) 2 then press it again to conrm the selection. Press the the

'MENU' button to conrm the input or output selection. Press multiple

times to display the IP settings.

61~4/A~D and Out/In: Press the Out or In button to select the output

or input mode and then press the required number or letter button to

change the selection.

For example, if outputs A~B need to be set to input 1 and outputs

C~D need to be set to input 2, then the following sequence of button

presses need to be performed:

Press: Out →A→B→In→1→Menu,

and then press: Out→C→D→In→2→Menu.

Note: If the menu button is not pressed the selection will not be changed.

6.2 Rear Panel

GND

CONTROL

RS232

SERVICE

IR OUTIR OUT

IR IN IR IN

ALL

CAT5e/6 OUT

IR OUT

IR IN

234A

IR OUT

IR IN

CAT5e/6 OUT

IR OUT

IR IN

CAT5e/6 OUT

IR OUT

IR IN

CAT5e/6 OUT

1 2 3 4

HDMI IN

DC 24V

V+

GND

V+

1 2 3 4 7 86 6

5 5

1RS-232: Connect to a PC or control system with D-Sub 9-pin cable for

RS-232 control.

2SERVICE: Manufacturer use only.

3CONTROL: Connect to an active network for Telnet/Web GUI control

(refer to Section 6.8 for details).

Warning: Please do not connect this port directly to the PC/Laptop

as the Telnet function will not work.

4ALL IR OUT: Connect to the IR blaster for IR signal transmission of the

source or display equipment. Place the IR blaster in direct line-of-sight

of the equipment to be controlled.

ALL IR IN: Connect to the IR extender for IR signal reception of the remote

control of this device or the source and display equipment. Ensure that

remote being used is within the direct line-of-sight of the IR extender.

5IR IN 1~4: Connect the IR extenders for IR signal reception. Ensure

that the remote being used is within the direct line-of-sight of the IR

extender.

IR OUT 1~4: Connect the IR blasters for IR signal transmission. Place the

IR blaster in direct line-of-sight of the equipment to be controlled.

6CAT5e/6/7 OUT A–D: Connect these CAT outputs to the CAT input port

of the receiver units with a single CAT5e/6/7 cable for HDMI Audio/Video

and IR control signal transmission.

7HDMI IN 1~4: Connect to the HDMI input source devices such as a

DVD player or a Set-top Box with HDMI cable or DVI to HDMI cable.

8DC24V: Connect the 24 V DC power supply to the unit and plug the

adaptor into an AC outlet.

6.3 Side Panel

1Ventilator: These are fan ventilation areas, DO NOT block these areas

or cover them with any object. Ensure there is adequate space around

the unit for air to circulate.

6.4 Remote Control

1Power:

Press this button to switch on the

device or set it to standby mode.

2IN:

Input ports selection 1~4.

3OUT:

Output ports selection A~D.

Note: IR Matrix control from Zones only

require the user to select the desired

input.

CR-121

IN OUT

Tabla de contenidos

Otros manuales de Conmutador de matriz de CYP

CYP

CYP HDBT PU-4H4HBTE-4K Manual de usuario

CYP

CYP CMSI-4H4CV Manual de usuario

CYP

CYP OR-YUV44S Manual de usuario

CYP

CYP CMPRO-U8H8CVE Manual de usuario

CYP

CYP CDPS-4H4HFS Manual de usuario

CYP

CYP OR-IR88 Manual de usuario

CYP

CYP CMSI-8H8HS Manual de usuario

CYP

CYP CPLUS-32FX Manual de usuario

CYP

CYP CMPRO-4H4H Manual de usuario

CYP

CYP OR-44U-4K22 Manual de usuario

CYP

CYP CMSI-48E Manual de usuario

CYP

CYP CMSI-8H8HC Manual de usuario

CYP

CYP PU-8H8HBTPL-4K Manual de usuario

CYP

CYP PU-8H8HBTPL Manual de usuario

CYP

CYP OR-42-4K22 Manual de usuario

CYP

CYP CPLUS-V4H4HPA Manual de usuario

CYP

CYP PUV-1210PL-RX Manual de usuario

CYP

CYP PU-424HBTL-KIT Manual de usuario

CYP

CYP PU-O4H4C Manual de usuario

CYP

CYP SM-2X2-HDMI-LC Manual de usuario

CYP

CYP nT14AX16 Manual de usuario

CYP

CYP CPLUS-44PLV Manual de usuario

CYP

CYP OR-H44E Manual de usuario

CYP

CYP OR-HD44E Manual de usuario

Manuales populares de Conmutador de matriz de otras marcas

Broadcast Tools

Broadcast Tools SS 8.2 Manual de usuario

Altimium

Altimium MATF32 Manual de usuario

ALFAtron

ALFAtron ALF-MUK44N Manual de usuario

Monoprice

Monoprice Blackbird 15377 Manual de usuario

Kramer

Kramer XL 3216VS Manual de usuario

PTN

PTN FMX12 Manual de usuario

Kramer

Kramer VP-2x2 Manual de usuario

Kramer

Kramer Sierra Video 6432V5xl Manual de usuario

TESmart

TESmart HMA0402A40 Manual de usuario

Octava

Octava HD4XSTPMX Manual de usuario

Intelix

Intelix FLX-88 Instrucciones de funcionamiento

Kramer

Kramer LASSEN XL 3232S Manual de usuario

Roland

Roland XS-1HD Manual de usuario

Kramer

Kramer VS-66HDCPxl Manual de usuario

Atlona

Atlona AT-HDMI-22M Manual de usuario

Link

Link HD8X8 Manual de usuario

AMX

AMX AVS-OP-2020-117 Instrucciones y recetas

Lindy

Lindy 38042 Manual de usuario