CYP PU-424HBTL-KIT Manual de usuario
PU-424HBTL-KIT
4 x 4 HDMI HDBaseT™ LITE Matrix (with 2 simultaneous
HDMI outputs) including 4x PU-514L-RX Receivers
OPERATION MANUAL
DISCLAIMERS
The information in this manual has been carefully checked and is
believed to be accurate. CYP (UK) Ltd assumes no responsibility for any
infringements of patents or other rights of third parties which may result
from its use.
CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be
contained in this document. CYP (UK) Ltd also makes no commitment to
update or to keep current the information contained in this document.
CYP (UK) Ltd reserves the right to make improvements to this document
and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed,
stored in a retrieval system, or any of its part translated into any language
or computer le, in any form or by any means—electronic, mechanical,
magnetic, optical, chemical, manual, or otherwise—without express
written permission and consent from CYP (UK) Ltd.
© Copyright 2011 by CYP (UK) Ltd.
All Rights Reserved.
Version 1.1 August 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate
this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts inside
the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if
it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sucient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE SUMMARY OF CHANGE
v1.00 29/01/13 First release
CONTENTS
1. Introduction ...........................................6
2. Applications ...........................................6
3. Package Contents ..................................6
4. System Requirements ...........................7
5. Features ..................................................7
6. Operation Controls and Functions .......8
6.1 Transmitter Front and Rear Panels ....... 8
6.2 Receiver Front and Rear Panels ............ 9
6.3 Side Panel ...................................................10
6.4 Remote Control ........................................10
6.5 IR Pin Assignment ....................................11
6.6 RS-232 Pin Assignment..........................11
6.7 RS-232 & Telnet Commands .................12
6.8 Telnet Control ............................................13
6.9 Web GUI Control ......................................15
7. Connection Diagram .......................... 17
8. Specications ...................................... 18
9. Acronyms ............................................. 19
6
1. INTRODUCTION
This 4 by 4 HDMI HDBaseT™ Lite Matrix with two additional simultaneous
HDMI outputs supports the transmission of video (resolutions up to
1080p Full HD and 1920x1200@60Hz), multi-channel digital audio, and
control via IR, RS-232, or Web GUI/Telnet IP, from four high denition
sources to four HDBaseT outputs over a single CAT5e/6/7 cable (up to
60m) for each output. Output A and C have additional mirrored HDMI
outputs, for added installation exibility.
The PU-424HBTL-KIT is supplied with 4x PU-514L-RX receivers which
utilise the 2-way IR control capabilities of the matrix.
Use the IP control feature to enable users to access and control the matrix
remotely and also allow additional options for integration of third-party
control systems. CYP provide control drivers for control systems such as
Control 4, RTI, Crestron, AMX, Control FX, and RTI. These are available at
no extra cost.
2. APPLICATIONS
Domestic HDMI Matrix system
Video/TV wall display and control
Security surveillance and control
Commercial advertising, display and control
University Lecture hall display and control
Retail Sales and demonstration
3. PACKAGE CONTENTS
4×4 HDMI Matrix over 4 CAT5e/6/7 with 2 HDMI outputs
4× PU-514L-RX Receivers
5×IR Extender
5×IR Blaster
1×24V/3.75A DC adaptor
1×Remote control
Operation manual
7
4. SYSTEM REQUIREMENTS
HDMI equipped source devices, connect with HDMI cables or DVI
equipped source, connect with DVI to HDMI cables
HDMI equipped displays (TVs or monitors) or HDMI equipped AV
receivers, connect with HDMI cables
Industry standard CAT5e/6/7 cables
5. FEATURES
Supports all v1.3 HDMI resolutions
Supports uncompressed video/audio up to 10.2Gbps
Common supported resolutions: HDTV: 480p, 576p, 720p, 1080i,
1080p, 1080p24; PC: VGA, SVGA, XGA, WXGA, SXGA, UXGA, WUXGA.
HDMI, HDCP and DVI complaint
High Denition Audio supported: Dolby TrueHD, Dolby Digital Plus
and DTS-HD Master Audio plus LPCM (up to 192kHz)
Uncompressed data transfer over single CAT cable (60m - CAT5e/6/7)
Supports third-party control systems, with drivers available for: Control
FX, AMX, Crestron, RTI, Control 4
Supports HDMI input up to 15m 1080p 8bit or 10m 1080p 12bit.
Supports RS-232, 2-Way IR, Manual Selection Buttons, and HDMI CEC
control pass through
Selectable EDID settings - TV (downstream) and STD (xed)
Compact 1U Rack mount design
Supports 3D signals
Supports additional IR Control via a master (ALL) Input/Output
Supports full IP control
Supplied with 4x PU-514L-RX receivers
Note:
1. Do not connect the CONTROL port to the CAT outputs of this device.
8
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
OUT
12
34IN
CMSI-424E
4X4 HDMI MATRIX
POWER LOCK MENU
AB
CD
61 2 3 4 5
1 LCM : Displays the setting information of each input and output
setting.
2 IR: IR Receiver window (accepts the remote control signal of this
device only).
3 POWER: Press this button to power the device on/o. The LED will
illuminate green when the power is on, red when it is in 'Standby'
mode.
4 LOCK: Press this button to lock all the buttons on the panel; press
again to unlock. The LED will illuminate when locked.
5 Menu: Press once to select EDID setting from STD (internal) 1 or TV
(external) 2 then press it again to conrm the selection. Press the the
'MENU' button to conrm the input or output selection
6 1~4/A~D and Out/In: Press the Out or In button to select the output
or input mode and then press the required number or letter button to
change the selection.
For example, if outputs A~B need to be set to input 1 and outputs
C~D need to be set to input 2, then the following sequence of button
presses need to be performed:
Press: Out →A→B→In→1→Menu,
and then press: Out→C→D→In→2→Menu.
Note: If the menu button is not pressed the selection will not be changed.
9
6.2 Rear Panel
1
IR IN IR OUT
2
IR IN IR OUT
3
IR IN IR OUT
4
IR IN IR OUT
HDMI OUT CAT5e/6 OUT
A
CAT5e/6 OUT
B
HDMI OUT CAT5e/6 OUT
C
CAT5e/6 OUT
D
HDMI IN 1 HDMI IN 2 HDMI IN 3 HDMI IN 4
CONTROL
RS232
DC 24V
1
2
3
4
V+
GND
GND GND
V+
IR OUT
IR IN
ALL
SERVICE
2 3
51110
1
4
86
7 9
1 RS-232: Connect to a PC or control system with D-Sub 9-pin cable for
RS-232 control.
2 CONTROL: Connect to an active network for Telnet/Web GUI control
(refer to Section 6.8).
Warning: Please do not connect this port directly to the PC/Laptop
as the Telnet function will not work.
3 SERVICE: Manufacturer use only.
4 HDMI OUT & CAT5e/6/7 OUT A/C: Simultaneous HDMI and HDBaseT
CAT5e/6/7 output. The HDMI output can be connected directly to a
display or to a point transmitter/receiver set. Connect the CAT5e/6/7
output to a compatible receiver unit to extend the signal up to 60 m.
5 CAT5e/6/7 OUT B/D: Connect from these CAT outputs to the CAT input
port of the receiver units with a single CAT5e/6/7 cable for HDMI Audio/
Video and IR control signal transmission.
6 HDMI IN 1~4: Connect to the HDMI input source devices such as a
DVD player or a Set-top Box with HDMI cable or DVI to HDMI cable.
7 IR IN 1~4: Connect the IR extenders for IR signal reception. Ensure
that the remote being used is within the direct line-of-sight of the IR
extender.
8 IR OUT 1~4: Connect the IR blasters for IR signal transmission. Place the
IR blaster in direct line-of-sight of the equipment to be controlled.
9 ALL IR OUT: Connect to the IR blaster for IR signal transmission of the
source or display equipment. Place the IR blaster in direct line-of-sight
of the equipment to be controlled.
10 ALL IR IN: Connect to the IR extender for IR signal reception of the remote
control of this device or the source and display equipment. Ensure that
remote being used is within the direct line-of-sight of the IR extender.
11 DC24V: Connect the 24 V DC power supply to the unit and plug the
adaptor into an AC outlet.
10
6.3 Side Panel
1
1 Ventilator: These are fan ventilation areas, DO NOT block these areas
or cover them with any object. Ensure there is adequate space around
the unit for air to circulate.
6.4 Remote Control
1 Power:
Press this button to switch on the device or set it to standby mode.
2 IN:
Input ports selection 1~4.
3 OUT:
Output ports selection A~D.
Note: IR Matrix control from Zones only require the user to select the
desired input.
1 A
B
2
C
3
4D
CR-121
IN OUT
1
23
Tabla de contenidos
Otros manuales de Conmutador de matriz de CYP
CYP
CYP CPLUS-V4H2HP-DT Manual de usuario
CYP
CYP OR-42UHD Manual de usuario
CYP
CYP CDPS-U10H2HFS Manual de usuario
CYP
CYP PU-O4H4C Manual de usuario
CYP
CYP CMLUX-44E Manual de usuario
CYP
CYP CMPRO-U8H8CVPL Manual de usuario
CYP
CYP PU-424HBTE Manual de usuario
CYP
CYP OR-42SA-4K22 Manual de usuario
CYP
CYP PUV-442-4K22 Manual de usuario
CYP
CYP PUV-662PL-4K22 Manual de usuario
CYP
CYP OR-HD88HC Manual de usuario
CYP
CYP PU-16H8HBT Manual de usuario
CYP
CYP MA-421 Manual de usuario
CYP
CYP PU-8H8HBTPL-4K Manual de usuario
CYP
CYP nT15GX01 Manual de usuario
CYP
CYP OR-44U-4K22 Manual de usuario
CYP
CYP SM-2X4-HDMI-LC Manual de usuario
CYP
CYP CMSI-1616 Manual de usuario
CYP
CYP CDPS-4H4HFS Manual de usuario
CYP
CYP PUV-44XPL-AVLC Manual de usuario
