CYP OR-IR88 Manual de usuario

OR-IR88

8 x 8 Bi-Directional Infra Red

Matrix Switcher

OPERATION MANUAL

Safety Precautions

Please read all instructions before attempting to unpack or install or

operate this equipment, and before connecting the power supply.

Please keep the following in mind as you unpack and install this

equipment:

 Always follow basic safety precautions to reduce the risk of

re, electrical shock and injury to persons.

 To prevent re or shock hazard, do not expose the unit to rain,

moisture or install this product near water.

 Never spill liquid of any kind on or into this product.

 Never push an object of any kind into this product through

module openings or empty slots, as you may damage parts.

 Do not attach the power supply cabling to building surfaces.

 Do not allow anything to rest on the power cabling or allow it to

be abused by persons walking on it.

 To protect the equipment from overheating, do not block the

slots and openings in the module housing that provide

ventilation.

Revision History

Version No Date Summary of Change

RDV1 20110530 Preliminary Release

RDV2 20111013 Front Panel &

Remote Control

Table of Contents

1. Introduction…………………………………………………........……….

2. Applications……………………..…………………………................….

3. Package Contents…………………………......…………….............…

4. System Requirements……...…………………..….…………........…….

5. Features…………………………………………….......……........………

6. Specications..………………………………………...........………...….

7. Hardware Description………………...……........….....................……

7.1 Front Panel ...............................................................................

7.2 Rear Panel …………………………………………..........…….…

8. IR Cable Pin Denitions………………...…….......….....................……

9. Remote Control …….………...................…………..........…..…..…...

9.1 IR Custom Code..........................................................................

9.2 Discrete IR codes for 8x8 HDMI matrix (IR3).............................

10. RS-232 Protocols..................................................................................

10.1 Pin Assignment...........................................................................

10.2 Commands.................................................................................

11. Connection and Installation..................…………..........…..…..…...

12. Acronyms …….………...................…………..........…..…...........…...

1. Introduction

The Bidirectional Infrared 8 by 8 IR Matrix is designed to work with HDMI matrix

together and allow the IR function to control your source devices from beside

your display/source. Using the original remote, you can control DVD/Blu-ray

players, satellite and set-top-boxes and with a cross matrix design this device

gives anyone the ability to send infrared signals from place to place. Simply

place the IR receiver near the display or player and put the IR balster in a po-

sition so that all devices will be able to receive IR signal properly, evenwhen

the sources are hidden in a cabinet or placed far away.

2. Applications

• Control multiple sources and displays

• System Control

• Showroom control

• Long distance IR control

3. Package Contents

• 8 by 8 Bidirectional Infrared Matrix

• Remote Control CR110 with battery

• 5V/2.6A DC power adaptor

• Operation Manual

• 9 IR Receiver cables

• 9 IR Blaster cables

4. System Requirements

Source equipment: Display/ TV/monitors and HDMI/video matrix box devices.

5. Features

• Supports independent IR receiver and IR blaster selection and control

• This device does not send audio/video signals, it only transmits and

receives infra-red signals to control equipment that is far away, using IR

extender cables

• Supports a frequency of 30KHz ~ 50KHz

• Use your existing remote controls

• Supports bidirectionally IR control from display and player side

6. Specications

IR Frequency 30KHz to 50KHz

Source Ports 8 x independent IR Blasters; 8 x independent IR Receivers;

1 x All IR blaster control; 1 x All IR receiver control;

TV ports 8 x independent IR Receiver; 8 x independent IR Blaster;

1 x All IR blaster control; 1 x All IR receiver control;

Power Supply 5VDC/2.6A (US/EU standards, CE/FCC/UL certied)

ESD Protection Human body model: ±8kV (air-gap discharge)

±4kV (contact discharge)

Dimensions (mm) 432 (W) x 174 (D) x 44 (H)

Weight(g) 2206

Chassis Material Aluminum

Silkscreen Color Black

Operating Temperature 0˚C~40˚C / 32˚F ~ 104˚F

Storage temperature -20˚C~60˚C / -4˚F ~ 140˚F

Relative Humidity 20~90% RH (non-condensing)

Power Consumption 1W

7. Hardware Description

The following sections describe the hardware components of the unit.

7.1 Front Panel

8x8 IR Matrix

Power All Lock Enter

1 2

5 6 7 8

3 4

RS232

AUX

RS232

MAIN

A12345678All

B C D E F G H All

TV SOURCE

DC 5V

Out

1 2 3 4 5 6 7

qLCM monitor: This screen will display the IR's source and TV selection

setting.

②IR: This IR window accepts the remote control signal of this device for

control the system.

③Power button & LED: Press this button to turn on the device or press it

again to set it to standby mode. The LED will illuminate in green when the

power is on and red when in standby mode.

④ALL: Press this button to select all TV's IR signal to switch to one Source's IR

signal. The sequence should be pressing All -> Number Key -> Enter.

tLOCK: Press this button to lock all the buttons on the panel and the green

LED will illuminate. To unlock press it again.

⑥ENTER:Pressthisbuttonaftereachandeveryselectiontoconrmthe

setting. If this button is not pressed after 20 seconds the selection will be

cancelled.

⑦1~8 (A~H) Buttons: Press these buttons to select both source and TV's IR

directionpressanumberkeyrst(forTVA~H)andthenpressanumber

keyagain(forSource1~8)andtoconrmtheselectionpressEnter.

7.2 Rear panel

8x8 IR Matrix

Power All Lock Enter

1 2

5 6 7 8

3 4

RS232

AUX

RS232

MAIN

A12345678All

B C D E F G H All

TV SOURCE

DC 5V

Out

1 2 53 4

qRS-232 AUX: This slot is where you connect the D-Sub 9pin with the desire

device for sending the RS-232 control signal.

②RS-232 MAIN: This slot is where you connect the D-Sub 9pin from the PC/NB

device for the RS-232 signal sending.

③TV In A~H: These slots are to connect with IR receivers for receiving

the IR signal at the TV side and blast out to the designated Source output

through the IR blaster.

TV In All: This slot is to connect with IR receiver for receiving the IR signals

at the TV side and blast out to Source outputs(1~8) through the IR blasters.

TV Out A~H: These slots are to connect with the IR blaster for blasting

out the IR signal received from the designated Source input through the

IR receiver.

TV Out All: This slot is to connect with IR blaster for blasting out the IR signal

received from the Source inputs(1~8) through the IR receivers.

④Source In 1~8: These slots are to connect with IR receivers for receiving

the IR signal at the Source side and blast out to the designated TV

output(s) through the IR blaster(s).

Source In All: This slot is to connect with IR receiver for receiving the IR

signals at the Source side and blast out to the TV outputs(A~H) through

the IR blasters.

Source Out 1~8: These slots are to connect with the IR blaster for blasting

out the IR signal received from the designated TV input(s) through the IR

receiver(s).

Source Out All: This slot is to connect with IR blaster for blasting out the IR

signal received from the TV inputs(A~H) through the IR receivers.

⑤DC 5V: Plug the 5V DC power supply into the unit and connect the

adaptor to an AC outlet.

8. IRCablePinDenitions

IR Receiver

① IR signal

② Power 5V

③ Grounding

① ② ③

IR Blaster

① ②

① Power 5V

② IR blaster signal

③ NC

③

Note: Both the IR Receiver & Blaster can support a frequency of

30~50KHz.

9. Remote Control

This remote control can be set with multipal format

according to the dipswitch setting. There are total

of four dipswitches with mainly two kinds of settings.

When dipswitches are all set to ON/↑the remote

control is able to control all outputs and all inputs.

For example, when output A wish to select input

5. Press A first and then press 5,

the output A will send and receive input source 5’s

IR signal instantly. Other settings please refer to section 9.2

section where output is based to control

input selections. For example, when all dipswitches

are set to OFF/↓this setting is base on output A

and therefore, it can only control inputs selection.

Hence, when output A wish to selelct input 3 press

3 only will allows output A to receive and send input

source 3’s IR signal. Further setting please refers to

section 9.2.

9.1 IR Custom Code

NO. DATA

1 88

2 89

3 8A

4 8C

5 8D

6 8E

7 90

8 91

9 92

0 95

9.2 Discrete IR codes for 8x8 HDMI matrix (IR3)

Select /

Dipswitch

input

output A ↓↓↓↓ 0cx88 0x89 0x8A 0x8C 0x8D 0x8E 0x90 0x91

output B ↑↓↓↓ 0x88 0x89 0x8A 0x8C 0x8D 0x8E 0x90 0x91

output C ↓↑↓↓ 0x88 0x89 0x8A 0x8C 0x8D 0x8E 0x90 0x91

output D ↑↑↓↓ 0x88 0x89 0x8A 0x8C 0x8D 0x8E 0x90 0x91

output E ↓↓↑↓ 0x88 0x89 0x8A 0x8C 0x8D 0x8E 0x90 0x91

output F ↑↓↑↓ 0x88 0x89 0x8A 0x8C 0x8D 0x8E 0x90 0x91

output G ↓↑↑↓ 0x88 0x89 0x8A 0x8C 0x8D 0x8E 0x90 0x91

output H ↑↑↑↓ 0x88 0x89 0x8A 0x8C 0x8D 0x8E 0x90 0x91

CR-110

IN OUT

2 3

10. RS-232 Protocols

10.1 Pin Assignment

25IR88 Remote Control Console

PIN Assignment PIN Assignment

1 NC 1 NC

2 Tx 2 Rx

3 Rx 3 Tx

4 NC 4 NC

5 GND 5 GND

6 NC 6 NC

7 NC 7 NC

8 NC 8 NC

9 NC 9 NC

Baud Rate: 9600bps

Data bit: 8 bits

Parity: None

Stop bit: 1

Flow Control: None

Tabla de contenidos

Otros manuales de Conmutador de matriz de CYP

CYP

CYP CDPS-U10H2HFS Manual de usuario

CYP

CYP CPLUS-V4H2HPIP Manual de usuario

CYP

CYP PRO-SDI44 Manual de usuario

CYP

CYP SM-2X2-HDMI-LC Manual de usuario

CYP

CYP CDPS-4H4HFS Manual de usuario

CYP

CYP PRO-F32M Manual de usuario

CYP

CYP PUV-1082-PRO Manual de usuario

CYP

CYP CMSI-8H8CVL Manual de usuario

CYP

CYP OR-YUV44S Manual de usuario

CYP

CYP CPLUS-662CVAL Manual de usuario

CYP

CYP CMSI-8H8HS Manual de usuario

CYP

CYP CMPRO-UA8H8HS Manual de usuario

CYP

CYP PUV-1082-4K22N Manual de usuario

CYP

CYP CMSI-8H8CV Manual de usuario

CYP

CYP nT14AX16 Manual de usuario

CYP

CYP PUV-1082-4K22 Manual de usuario

CYP

CYP PU-442PL-KIT Manual de usuario

CYP

CYP CDPS-44SM Manual de usuario

CYP

CYP CMSI-4H4CVL Manual de usuario

CYP

CYP PU-424HBTE Manual de usuario

CYP

CYP CPLUS-44PLV Manual de usuario

CYP

CYP OR-32USBC-4K22 Manual de usuario

CYP

CYP nT15GX01 Manual de usuario

CYP

CYP OR-HD88S Manual de usuario

Manuales populares de Conmutador de matriz de otras marcas

Broadcast Tools

Broadcast Tools SS 8.2 Manual de usuario

Altimium

Altimium MATF32 Manual de usuario

ALFAtron

ALFAtron ALF-MUK44N Manual de usuario

Monoprice

Monoprice Blackbird 15377 Manual de usuario

Kramer

Kramer XL 3216VS Manual de usuario

PTN

PTN FMX12 Manual de usuario

Kramer

Kramer VP-2x2 Manual de usuario

Kramer

Kramer Sierra Video 6432V5xl Manual de usuario

TESmart

TESmart HMA0402A40 Manual de usuario

Octava

Octava HD4XSTPMX Manual de usuario

Intelix

Intelix FLX-88 Instrucciones de funcionamiento

Kramer

Kramer LASSEN XL 3232S Manual de usuario

Roland

Roland XS-1HD Manual de usuario

Kramer

Kramer VS-66HDCPxl Manual de usuario

Atlona

Atlona AT-HDMI-22M Manual de usuario

Link

Link HD8X8 Manual de usuario

AMX

AMX AVS-OP-2020-117 Instrucciones y recetas

Lindy

Lindy 38042 Manual de usuario