CTA ADD-PARAFS Manual de usuario

x4

x4

x1 x1

x4

x4

x8

INSTALLATION:

1A. Align the holes of the body (A) to the

base plates (B) as illustrated. Rotate in

(4) screws (G) using provided tool (J)

until securely tightened.

1. Mounting Base to Body

PACKAGE CONTENTS:

x4 x1

2. Setting up Cable Routing

2A. Using the provided weighted pendant, route the cable through the stand. You must first remove the VESA adapter

using provided allen tool to unscrew. Using the pendant tool (C), affix/tie the cable first, then fish it through the large hole

at the top, drop it through the body and fish the cable through until it has come out the backside hole as illustrated. After,

reattach the VESA adapter with screws (G) and provided tool. Make sure to pull cable through hole before you reattach

as illustrated above.

**Cable for device for

illustration and not

included

3. Adjusting VESA Adaptor

3A. Using provided tool (F),

rotate clockwise to lock

VESA adapter in place.

Rotate counterclocwise to

loosen and flex the adapter

for flexibility when VESA

compatible item is installed.

x1

CTA Digital Floor Stand Component

For Kitting

ADD-PARAFS / ADD-PARAFSW / ADD-PARAFSS

INSTRUCTION - MANUAL

4. Setting up VESA Compatible Items

x4 **Enclosure and cable

for illustration and not

included

4A. Align the VESA holes of the body (A)

to the holes of your VESA compatible

device as illustrated. Rotate in (4) screws

(H) using provided tool (J) until securely

tightened.

x4

x4

5. Anchoring Base (Optional)

5A. Pre-drill holes into the surface aligning with

floorstand drill holes using drill (not included). Insert

anchors first into holes (E), and drill in screws from

top until securely fastened. If not screwing into

surface, using fillers (D) to plug into holes for a

seamless finish.

**Tablet for illustration

and not included

6. Removing VESA Adaptor for Monitor Setup

6A. Located the endcap piece on the side of VESA adaptor as illustrated and

remove with fingers. Using provided tool (F), loosen sides as shown. Remove the X

VESA center component

7. Attaching Monitor and Reassembling

7A. Align the now removed X VESA component with the VESA holes on

the back of your monitor. Rotate in the screws (I) using provided allen

key tool until securely tightened.

7B. WITH the X VESA attached to the monitor, place the entire setup

back onto the floor stand body. Align the VESA joint with the original hole

as shown above. Then using the provided tool, tighten the now

connected VESA joint. Place in the fillers for a seamless look afterwards.

**Monitor for

illustration and not

included

**Monitor for

illustration and not

included

x4

Este manual sirve para los siguientes modelos

2

Otros manuales de Rack y soporte de CTA

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario