CTA PAD-2VDMB Manual de usuario

Dual VESA Security Enclosure Desk Mount

w/ Storage Compartment (Black / White)

PAD-2VDMB/ PAD-2VDMW

INSTRUCTION - MANUAL

CONTENTS:

INSTALLATION:

888-733-4448

1. Mounting Setup

x1

M5 Allen Key

M5 x 8

M5 Nut

M5 x 12

A

B

(x4)

(x4)

M6 Allen key

(x4)

x4

C D E F G

x8 x8 x4 x1 x1

1A. When mounting into a surface for a desk

mount mode, use (4) screws and (4) anchors as

illustrated (B) and rotate through desk mount (A).

Using a screwdriver (not provided), rotate in until

securely tightened as shown above.

1B. When mounting into CTA Digital’s

ADD-PARAFS2 stands, first open the back

door to the storage area. Then use the

provided allen key tool (I) and rotate in

screws (H) on top of the washers (J) as

shown until securely fastened. Shut door

and lock with key. (G)

M6 x 16

x4 x4

H J

**Screw Driver is for

illustration purposes and

not included

B

M6 Allen Key

I

x1

I

H

M6 x 16

J

A

**Floor Stand is for

illustration purposes and

not included

A

Mounting to Direct Surface Mounting to Another

Vesa Compatible Item

OR

x2 x2

Foam Adapter &

Sheet Bundle

**Tablet shown for

illustration and

NOT INCLUDED.

KL

888-733-4448

2A. Align VESA holes of CTA’s enclosure (K) with one set of the

desk mount (A) VESA holes in landscape orientation. Using the

included allen key tool (F), rotate in screws (C) while holding hex

nut (D) on the back side until securely tightened. Repeat the

process for the other set of VESA holes and other enclosure.

3. Setting up Cable Routing and Access

to Back Storage Area

3A. Unlock back storage area using the keys (G). Fish through the

holes your cable as shown into the back storage area. Either ish

though the holes at the bottom if required or even connect to any small

charging items, device or accessories as needed that can fit into the

space.

F

M5 x 12

C

x4

x1

x4

D

M5 Nut

A

2. Setting Up Enclosures

K

4A. Lock or unlock your tablet enclosure (K) with

security key (G) as shown. Make sure to do a full 360 degree rotation

before removing.

4B. Find the appropriate size foam padding / sheet (L) for the device you

wish to use. Make sure the device is compatible for the enclosure before

starting. Lay in device and connect any cables/cords as needed. There

are sticker notes at the corners to identify which device is compatible

4C. If needed, lay-in correct included masking insert. The foam insert is

to block and excess space and make a seamless fit for smaller tablets

Close and lock enclosure afterwards and you’re set.

**Tablet shown for

illustration and

NOT INCLUDED.

**Tablet shown for

illustration and

NOT INCLUDED.

K

G

L

L

4. Setting up Tablet Enclosure Interior Foam Adapters, Sheet Adapter and Security

Este manual sirve para los siguientes modelos

1

Otros manuales de Rack y soporte de CTA

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario