Pyle PMKSPAD1 Manual de usuario

PMKSPAD1

Multimedia Microphone Stand With Adapter for iPad 2

(Adjustable for Compatibility w/iPad 1)

http://www.pyleaudio.com

Thanks for purchasing the PMKSPAD1, an innovative

new stand adaptor from Pyle that allows you to use a

microphone stand to hold your iPad 2. It securely holds

your iPad with sure-grip touch points, preventing

scratching or marring. Easily snap it in or out with the

quick-snap clips. Just screw it on to the included

microphone stand, or use your own. Try it on the boom

for increased mobility, or place it vertically on the stand

for stability. The iPad can be used in portrait and

landscape modes.

Specifications:

Sturdy, Durable Construction With Sure-Grip Touch

Points — Securely Holds Your iPad Without

Scratching Or Marring It

Multi-Angle Adjustment Allows Precise Positioning

For Optimal Stage Or Studio Viewing

Quick-Snap Clips Provide Fast, Secure iPad Insertion

Fast Installation — On Your Mic Stand In Seconds

With The Twist Of A Knob

All Controls, Buttons And Connectors Are

Accessible When Your iPad Is Clipped On

Can Be Mounted On The Vertical Part Of A Mic

Stand, Or On A Horizontal Boom

Also Compatible With The iPad 1

Your kit includes one (1) set of the following items:

1 x tripod base bar

1 x extender bar

1 x boom bar

1 x multi-mount boom clip

1 x iPad holder with universal clip

1. Start with the tripod base bar piece.

Loosen the screw so that you can lower the

tripod stand to extend the legs. Then tighten

to secure the legs in place.

2. Next, insert the extender bar into the

tripod. The extender bar is threaded on one

end, and has a moveable grip on the other.

Make sure you do not use the boom extender,

which does not have a moveable grip. Then

screw the handlebar into place.

3. Screw on the multi-mount boom clip, then

insert the boom bar. Rotate the silver bar

clockwise to tighten the mechanism.

4. Note: For compatibility with the iPad 1,

you will need to make adjustments to the four

clips, as it is slightly larger than the iPad 2. If

you have the iPad 2, skip this step. Remove

the rubber pads. Then, using a pair of pliers,

carefully bend each corner on the iPad holder

slightly back.

5. Now, attach the iPad holder to the

extended boom bar by loosening the screw,

sliding it on, and then tightening the screw

when you find a spot you find appropriate.

Your stand is now ready to use!

Tabla de contenidos

Otros manuales de Rack y soporte de Pyle

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario

Vivo

Vivo MOUNT-HP23XW Manual de usuario