CTA PAD-PARAFDC Manual de usuario

Premium Locking Floor Stand Kiosk w/

Digital Password Combination Security Enclosure

PAD-PARAFDC

INSTRUCTION - MANUAL

CONTENTS:

INSTALLATION:

1. Assembling floorstand base :

A

J

x1

M5 Allen Key

3. Attaching enclosure to VESA plate :

1A. Allign the holes on the sntad (A) with holes on the base (B) and turn

in screws (F) with provided allen tool (K) until securely tightened. Shown

above.

2B. When the cable reaches the

bottom of the stand, pull through

the hole at the stand back and

remove the weighted pendant

as shown.

2A. To route a charge cable

through the stand, attach the

weighted pendant to your

charge cable, then pass through

the cutout at the top of the

stand.

3A. Align enclosure (C) VESA holes to VESA plate holes in stand (A) and

from the front of enclosure turn in screws (D) into the threaded VESA

holes with provided allen tool (J) until securely thigtened. Shown above.

C

x1

E

x4

M5 NutM5 x 10

D

x4

M5 x 10

x4

B

x1

x1

K

x1

M6 Allen Key

x1

I

M6 x4

F

x4

M6

2. Cable routing :

C

A

J

A

B

F

K

D

G

I

4. Setting up the foam adapters :

4A. Identify the double sided adhesives (G). Peel away the backing on

both sides. Adhesive four of them behind the foam pieces (I) as

illustrated. They are to adhese the foam to the enclosure. Peel away

the back on the next four and place them on top of the foam pieces as

illustrated. These are to attach the foam to the tablets and ensure

security.

x1

H

x1

G

888-733-4448

5A. When installing device into the enclosure, identify where the camera is.

Then simply remove and pop out the cover prior to mounting or setting up

tablet to properly expose camera.

5. Removing Enclosure Back Opening Covers :

6. Locking Enclosure :

6A. Once tablet is inserted, close the front cover securely.

6B. After, turn the digital lock 90 degrees clockwise.

This will lock the tablet in place.

**See following page

for digital lock usage

and setup

7A. Identify the lock chart port on the bottom side as illustrated. Plug in provided

charging cable (H) from one end to another to properly charge digital lock.

7. Charge the lock :

H

**Tablet shown for

illustration only,

NOT INCLUDED.

**Tablet shown for

illustration only,

NOT INCLUDED.

8A. Enclosure can be mounted in vertical and horizontal positions as

needed. Shown above.

8. Portrait & Landscape modes :

**Tablet shown for

illustration only,

NOT INCLUDED.

**Tablet shown for

illustration only,

NOT INCLUDED.

C

C

I

I

4. Inserting Tablet into Enclosure :

4A. With the enclosure open, insert tablet into the foam adapters (I). Make

sure the adhesives have been placed ahead of time or tablet will fall out.

Plug your tablet into any cables/wires you have routed to the enclosure.

After tablet is secure, close the top and lock into place.

888-733-4448

Otros manuales de Rack y soporte de CTA

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario