CTA PAD-2VDMWA Manual de usuario

Dual Acrylic Enclosure Desk Mount

w/ Storage Compartment

PAD-2VDMWA

INSTRUCTION - MANUAL

CONTENTS:

888-733-4448

x1

M5 Allen Key

M5 x 8

M5 Nut

M5 x 12

AD E F

x8 x8 x4 x1

M6 x 16

x4 x4

I K

H

x4

CB

x1

N

M6 Allen Key

J

x1

x4

x4

Flat Head

Star Screw

L

M

G

x2

Rounded Head

Star Screw

Security Star Key

x2

INSTALLATION:

1. Mounting Setup

(x4)

(x4)

M6 Allen key

(x4)

1A. When mounting into a surface for a desk

mount mode, use (4) screws and (4) anchors as

illustrated (H) and rotate through desk mount (A).

Using a screwdriver (not provided), rotate in until

securely tightened as shown above.

1B. When mounting into CTA Digital’s

ADD-PARAFS2 stands, first open the back

door to the storage area. Then use the

provided allen key tool (J) and rotate in

screws (I) on top of the washers (K) as

shown until securely fastened. Shut door

and lock with key. (N)

**Screw Driver is for

illustration purposes and

not included

H

J

I

M6 x 16

K

A

**Floor Stand is for

illustration purposes and

not included

A

Mounting to Direct Surface Mounting to Another

Vesa Compatible Item

OR

888-733-4448

3A. Unlock back storage area using the keys (N). Fish through the holes your

cable as shown into the back storage area. Either ish though the holes at the

bottom if required or even connect to any small charging items, device or

accessories as needed that can fit into the space.

4A.While holding the back security star key (D) tight in place Turn the

front security star key (D) counter clock-wise until all 4 screws (B) are

unscrewed.Then take of front part of enclosure.

4B. Using one of the compatible listed tablets, insert into the

L-shaped adapters for a secure and tight fit.Insert tablet in back

part of enclosure (A) as shown. Watch out orientation of tablet.

G

L

B

4C. Take the detached enclosure top (B), align the corner holes with the bottom portion. Then use the provided

security star key (G), turn in clock-wise the star screws until securely tightened while holding the security star

key (G) on the other side with your other hand. Screw in until securely tightened.

G

B

L

x4

B

F

M5 x 12

C

x4

x1

x4

D

M5 Nut

A

3. Setting up Cable Routing and Access to

Back Storage Area

2. Setting Up Enclosures

2A. Align VESA holes of CTA’s acrylic enclosure (B) with one set of the

desk mount (A) VESA holes in landscape orientation. Using the included

allen key tool (F), rotate in screws (C) while holding hex nut (D) on the

back side until securely tightened. Repeat the process for the other set of

VESA holes and other enclosure.

4. Setting up Acrylic Tablet Enclosures

**Tablets shown are for

illustration purposes and

not included

Otros manuales de Rack y soporte de CTA

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario