Clarke DEVIL 4035 Manual de instalación y operación

FAN HEATER

OPERATING & MAINTENANCE

INSTRUCTIONS 1008

Models: DEVIL 4035 • 4055 • 4090 • 4115

FAN HEATER

PARTS & SERVICE TEL: 020 8988 7400

or e-mail as follows:

PARTS: [email protected]

SERVICE: [email protected]

PARTS & SERVICE

Model Number Devil 4035 Devil 4055 Devil 4090 Devil 4115

Input 230V 50hz 1ph 400V 50hz 3ph 400V 50hz 3ph 400V 50hz 3ph

Output Rating 1.5 - 3kW 2.5 - 5kW 3, 6 & 9kW 7.5 - 15kW

Absorbed Power 3kW 5kW 9kW 15kW

Fuse Rating 13A 15A 15A 25A

Dimensions (mm) 250x250x420 250x250x420 380x330x590 440x350x600

Air Output 400m3/h 400m3/h 800m3/h 1300m3/h

Noise Level 50dBL

50dBL

52dBL

54dBL

Gross Weight 7.5kg 8.0kg 13.5kg 15.5kg

Part No. 6925140 6925145 6925150 6525155

SPECIFICATIONS

DECLARATION of CONFORMITY

We declare that this product complies with the following standards/directives:

•73/23/EEC

•98/336/EEC

Serial/Batch No: See Data Plate

signed

Waste electrical products should not be disposed of with household waste. Please

dispose of at your local recycling facility.

Thank you for purchasing this Clarke Ceramic Heater.

Before attempting to operate the unit please read this instruction leaflet and carefully

follow all directions given. By doing so you will ensure safe operation of the unit and you

can also look forward to it providing you with long and trouble free service.

GUARANTEE

This CLARKE product is guaranteed against faults in manufacture for 12 months

from purchase date. Please keep your receipt as proof of purchase.

This guarantee is invalid if the product has been found to have been abused in

any way, or not used for the purpose for which it was intended, or to have been

tampered with in any way. The reason for return must be clearly stated.

This guarantee does not affect your statutory rights.

SAFETY PRECAUTIONS

• NEVER use electrical equipment in the presence of combustible gases.

• This heater is for INDOOR USE ONLY.

• ALWAYS disconnect from the mains supply before moving or performing any

maintenance tasks.

• ALWAYS use in an upright position ONLY.

• Inspect the mains cable regularly for signs of damage. DO NOT use if it is

damaged, and ALWAYS keep it away from the source of heat.

• NEVER switch ON the heater if the guard is removed.

• NEVER locate the heater near combustible materials such as curtains, furniture

etc. Allow at least 1 metre distance.

• DO NOT use this heater in a bathroom , shower room, in the vicinity of a

swimming pool, or any wet environment.

• DO NOT locate the heater close to an adjacent wall or ceiling...allow a

distance of at least 1 metre from a wall or ceiling.

• NEVER cover the heater, or block any of the vents.

• DO NOT use if the heater elements are damaged or broken.

• NEVER touch the heater for at least 15 minutes after it is switched off.

• DO NOT leave the heater unnattended.

• If children are present.....ALWAYS use with a fireguard.

• Do NOT use in a paint spray booth or any explosive environment.

• Take care to ensure that the fan grille cannot be blocked by curtains or the like.

ELECTRICAL CONNECTIONS

This model is provided with a 13 amp BS 1363 plug, fitted with a 13amp fuse and

MUST be connected to a standard, 230 Volt (50Hz) electrical supply, preferably

through an approved plug , or a suitably fused isolator switch.

WARNING! THIS APPLIANCE MUST BE EARTHED

IMPORTANT: The wires in the mains lead are coloured in accordance with the

following code:

Green & Yellow ........................ Earth

Blue ............................................ Neutral

Brown ........................................ Live

As the colours of the flexible lead of this appliance may not correspond with the coloured

markings identifying terminals in your plug, or your mains supply, proceed as follows:

• Connect GREEN & YELLOW coloured cord to plug terminal marked with a letter “E” or

Earth symbol “ ” or coloured GREEN or GREEN & YELLOW.

• Connect BROWN cord to terminal marked with a letter “L” or coloured RED.

• Connect BLUE cord to terminal marked with a letter “N” or coloured BLACK.

Fuse Rating

The fuse in the plug must be replaced with one of the same rating (13 amps) and this re-

placement must be ASTA approved to BS1362.

This appliance is fitted with a plug which is moulded on to the electric cable (i.e. non-

rewireable) please note:

1. The plug must be thrown away if it is cut from the electric cable. There is a danger of

electric shock if it is subsequently inserted into a socket outlet.

2. Never use the plug without the fuse cover fitted.

3. Should you wish to replace a detachable fuse carrier, ensure that the correct

replacement is used (as indicated by marking or colour code).

4. Replacement fuse covers can be obtained from most DIY or electrical stores.

Devil 4035

These machines MUST be connected to a 400 Volt, 3 PHASE 50Hz supply through a suitably

fused isolator switch. It cannot be operated from a single phase supply.

A trailing socket should be wired as follows:

Devils 4055, 4090 & 4115

• Connect the GREEN or GREEN & YELLOW coloured

wire, to the terminal marked with the letter “E” or Earth

symbol “ ”

• Connect the BLACK wire to the ‘N’ or Neutral terminal.

• Connect the Remaining wires to the terminals marked

`L1, L2 and L3.

OPERATION

With the heater suitably sited (ensure you comply with all safety precautions),

switch the heater ON to either half or full output. Model Devil 4090 has three settings

- 1/3, 2/3 and full power (see specification chart on page 2).

A temperature control (F) is also provided for fine control of heat output.

Should the unit overheat, a thermal cutout will operate, shutting down the unit.

Allow a period of time for the unit to cool (approx. 10 minutes) before pressing the

reset using a suitable tool, and restarting.

When switching the unit OFF, it is strongly recommended that the unit is run in the

FAN ONLY mode for approx. 10 minutes, in order to cool the elements, before

switching OFF completely and finally disconnecting from the mains supply.

The thermal cutout may also operate if the heater is shut down without allowing

to cool sufficiently. If, subsequently, the machine fails to start, press the reset using

a suitable tool and try again.

NOTE: Model 4090 is provided with 3 heat settings: 1/3, 2/3 and full power

A. Off

B. Fan only

C. Half Power output*

D. Full power output*

E. Reset

F. Temperature Control

* with temperature control at MAX.

MAINTENANCE

Before performing any maintenance tasks, if the heater has been used, ALWAYS

allow it to cool down for at least 10 minutes (by switching the heater OFF, but

leave the fan running), then disconnect from the mains supply.

Periodically.

• Disconnect from the mains supply, and use compressed air to clean out the

unit. ALWAYS wear a dust mask to perform this operation.

If there is any serious build up of dirt, remove the front and rear grilles and

clean the fan and elements thoroughly with a damp cloth

• Inspect the mains cable for damage. Heat damage will cause the cable to

stiffen and crack. If this is found, have the cable replaced. Check cable routing

and ensure it is well away from the heat source.

WARNING!

IF YOU ARE IN ANY DOUBT ABOUT ELECTRICAL CONNECTIONS, CONSULT A

QUALIFIED ELECTRICIAN.

DO NOT ATTEMPT ELECTRICAL CONNECTIONS or REPAIRS YOURSELF.

SPARE PARTS - DEVIL 4035

1 HANDLE RPC01002

2 UPPER PANEL RPC63007

3 SENSOR HOLDER RPC01006

4 HEATING ELEMENT

HOLDER RPC62002

5 FAN RPC800202

6 MOTOR RPC800205

7 BACK GUARD RPC63008

8 POWER CABLE WITH

PLUG RPC800208

9 LEFT PANEL RPC63009

10 TERMINAL BOARD RPC800209

11 SAFETY THERMOSTAT

BRACKET (part. 1/2) RPC01007

12 SAFETY THERMOSTAT

BRACKET (part. 2/2) RPC01008

No. Description Part No. No. Description Part No.

13 SAFETY THERMOSTAT RPC36007

14 RIGHT PANEL RPC63010

15 ROOM THERMOSTAT RPC800214

16 SWITCH RPC320034

17 FIXING RING RPC01005

18 KNOB RPC010142

19 CONTROL PANEL RPC63011

20 HEATING ELEMENT RPC07004

21 ROOM THERMOSTAT

BRACKET RPC63012

22 BOTTOM BOARD RPC63012

24 FOOT RPC02001

25 FRONT GRILL RPC24002

SPARE PARTS - DEVIL 4055

1 HANDLE RPC01002

2 UPPER PANEL RPC63007

3 SENSOR HOLDER RPC01006

4 HEATING ELEMENT

HOLDER RPC62003

5 FAN RPC800203

6 MOTOR RPC800206

7 BACK GUARD RPC63008

8 POWER CABLE WITH

PLUG RPC63008

8 4 PIN PLUG RPC800194

9 TERMINAL BOARD RPC800209

10 SAFETY THERMOSTAT

BRACKET (part. 1/2) RPC01007

11 SAFETY THERMOSTAT

BRACKET (part. 2/2) RPC01008

No. Description Part No. No. Description Part No.

12 RELAY RPC800218

13 SAFETY THERMOSTAT RPC800212

14 INSULATING COVER RPC63014

15 LEFT PANEL RPC63009

15 RIGHT PANEL RPC63010

16 ROOM THERMOSTAT RPC800215

17 SWITCH RPC32002

18 FIXING RING RPC01005

19 KNOB RPC010142

20 CONTROL PANEL RPC63013

21 HEATING ELEMENT RPC800217

22 ROOM THERMOSTAT

BRACKET RPC63012

24 BOTTOM PANEL RPC63012

25 FOOT RPC02001

26 FRONT GUARD RPC24002

SPARE PARTS - DEVIL 4090

1 TRAILING SOCKET RPC20430019

2 FIXED PLUG RPC20430023

3 UPPER PANEL RPC20630268

4 HANDLE RPC20010007

5 CASING PANEL RPC20630269

6 BASE PANEL RPC20630267

7 MOTOR RPC20400069

8 JOINT RPC20010038

9 FAN RPC20200021

10 4 POSITION SWITCH RPC20320025

No. Description Part No. No. Description Part No.

11 AIR INLET RPC20620929

12 ELECTRONIC BOARD RPC20470026

13 SPACER RPC20010068

14 BOARD SUPPORT RPC20620930

15 THERMOSTAT RPC20360024

16 CONTROL PANEL RPC20620925

17 KNOB RPC20320024

18 CLIP RPC20230254

19 FRONT GUARD RPC20240040

20 HEATING ELEMENT RPC20070028

SPARE PARTS - DEVIL 4115

1 FIXED PLUG RPC20430020

2 TRAILING SOCKET RPC20430021

3 PLUG BRACKET RPC20620956

4 LEFT SIDE PANEL RPC20630279

5 HANDLE RPC20610117

6 CAP RPC20020005

7 CONTROL PANEL RPC20620957

8 3 POSITION SWITCH RPC20320026

9 SPACER RPC20010068

10 BOARD SUPPORT RPC20620930

11 ELECTRONIC BOARD RPC20470026

12 TEMP. REGULATOR RPC20360024

No. Description Part No. No. Description Part No.

13 UPPER PANEL RPC20630277

14 RIGHT SIDE PANEL RPC20630280

15 KNOB RPC20320024

16 MOTOR RPC20400069

17 JOINT RPC20010038

18 FAN RPC20200067

19 INSULATING PANEL RPC20060021

20 BASE PANEL RPC20630278

21 AIR INLET RPC20620955

22 HEATING ELEMENT RPC20070027

23 FRONT GUARD RPC20240041

WIRING DIAGRAMS

Devil 4035

Devil 4055

Otros manuales para DEVIL 4035

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Calentador de Clarke

Clarke

Clarke CONTRACTOR DEVIL371PD Manual de instalación y operación

Clarke

Clarke DEVIL IRD40B Manual de instrucciones

Clarke

Clarke Devil 6003 Manual de instrucciones

Clarke

Clarke Devil 370P Manual de instalación y operación

Clarke

Clarke DEVIL 370PD Manual de instalación y operación

Clarke

Clarke DEVIL 371SPD Manual de instalación y operación

Clarke

Clarke Devil IRD20B Manual de instrucciones

Clarke

Clarke XR60 Manual de instalación y operación

Clarke

Clarke 6933990 Manual de instrucciones

Clarke

Clarke Devil 6002 Manual

Clarke

Clarke OFR13/250 Manual de instrucciones

Clarke

Clarke DEVIL 7005 Manual de instrucciones

Clarke

Clarke Devil 6003 Manual

Clarke

Clarke DEVIL 7030 Manual de instrucciones

Clarke

Clarke DEVIL 370PC Manual de instalación y operación

Clarke

Clarke 6933985 Manual de instrucciones

Clarke

Clarke DEVIL 7003 Manual de instrucciones

Clarke

Clarke DEVIL 2000PTC-B Manual de instrucciones

Clarke

Clarke DEVIL 371SPC Manual de instalación y operación

Clarke

Clarke XR60DV Manual de instrucciones

Clarke

Clarke DEVIL 2800PTC-B Manual de instrucciones

Clarke

Clarke DEVIL 7030 Manual de instrucciones

Clarke

Clarke OFR 5/50 Manual de instrucciones

Clarke

Clarke XRV100 Guía de solución de problemas

Manuales populares de Calentador de otras marcas

oventrop

oventrop Regucor Series Manual de usuario

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manual de usuario

ELMEKO

ELMEKO ML 150 Manual de usuario

BN Thermic

BN Thermic 830T Manual de usuario

KING

KING K Series Guía

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guía de inicio rápido

Well Straler

Well Straler RC-16B Manual de usuario

EUROM

EUROM 333299 Manual de usuario

Heylo

Heylo K 170 Manual de usuario

Eterna

Eterna TR70W Manual de usuario

IRSAP

IRSAP The Radiator Company Ovali Manual de usuario

Empire Heating Systems

Empire Heating Systems WCC65 Manual de usuario

Wetekom

Wetekom 92 86 43 Manual de usuario

Desa

Desa SPC170-F Manual de usuario

Watlow

Watlow Watrod Electric Tubular Heaters Manual de usuario

Haverland

Haverland ECO-DRY GPS Series Manual de lista de piezas

Stelpro

Stelpro ASILVC2060 Series Manual de usuario

iLO

iLO IHP2424 Manual de funcionamiento