Clarke DEVIL 7030 Manual de instrucciones

Only suitable for well insulated areas and not designed

to be the primary heat source

OPERATION & MAINTENANCE

INSTRUCTIONS

DL1123- Rev 11

ORIGINAL INSTRUCTIONS

30KW ELECTRIC FAN HEATER

MODEL NO: DEVIL 7030

PART NO: 6935458

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE product.

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

FUNCTION AND OPERATING PARAMETERS

This is a forced air heater. It’s intended use is for drying and the warming of

commercial/industrial buildings and areas where adequate ventilation is

provided.

• It must be operated as prescribed in the operating manual.

• It is not intended to be used for domestic use or for the heating of

habitable areas.

• It is not intended to be used to reach and maintain a certain level of

human thermal comfort within an enclosed space in which the heater is

situated.

• It is not intended to be used in enclosed areas with restricted ventilation.

• It is not intended for warming animals or live stock.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

THE FOLLOWING TABLE ADDRESSES THE INFORMATION

REQUIREMENTS OF REG.2015/1188

Item Symbol Value Unit

Heat output

Measured seasonal space heating energy efficiency 36%

Nominal heat output Pnom 30 kW

Minimum heat output (indicative) P min 15 kW

Maximum continuous heat output P max 30 kW

Auxiliary electricity consumption

At nominal heat output elmax n/a kW

At minimum heat output el min n/a kW

In standby mode elSB 0kW

Type of heat input for electric storage local heaters only

Manual heat charge control with integrated thermostat No

Manual heat charge control with room and/or outdoor temperature

feedback

Electronic heat charge control with room and/or outdoor temperature

feedback

Fan assisted output No

Type of heat output/room temperature control (select one)

Single stage heat output, no temperature control No

Two or more manual stages, no temperature control No

With mechanical thermostat temp control Yes

With electronic temperature control No

Electronic temperature control with day timer No

Electronic temperature control with week timer No

Other control options (multiple selections possible)

Room temperature control with presence detection No

Room temperature control with open window detection No

Room temperature control with distance control option No

Room temperature control with adaptive start control No

Room temperature control with working time limitation No

Room temperature control with black bulb sensor No

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY SYMBOLS

The following symbols appear on the unit.

SAFETY RULES

Make sure that you read, understand and comply with the following.

ELECTRICAL SAFETY

1. Electrical appliances must match the power outlet. NEVER modify the plug

in any way. DO NOT use adaptor plugs with earthed (grounded)

appliances. Correct plugs and outlets will reduce the risk of electric shock.

2. DO NOT abuse the electrical cable. NEVER use the cable for pulling or

unplugging the heater. Keep the cable away from sources of heat, oil,

sharp edges or moving parts. Damaged or tangled cables increase the risk

of electric shock.

3. Keep the power cable well away from machines and ensure an adequate

electrical supply is close at hand so that the operation is not restricted by

the length of the cable.

4. ALWAYS disconnect from the power supply before moving the heater or

performing any cleaning or maintenance tasks.

5. Inspect the mains cable regularly for signs of damage. DO NOT use if it is

damaged, and ALWAYS keep it away from the source of heat.

6. Check the heater for damage before use. DO NOT use if the heater tubes/

elements are damaged or broken. Any damage should be properly

repaired or the part replaced. If in doubt, DO NOT use. Consult your local

CLARKE dealer.

Hot

Surface,

Do Not

Touch

Do Not

Cover

High

Voltage

WARNING: THIS HEATER MUST BE EARTHED

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

MAINTENANCE.

1. Check that the heater is in good working order. Take immediate action to

repair or replace damaged parts.

2. DO NOT allow the heating elements to become covered with dust which

could become a fire hazard. If used in a dusty workplace it should be

cleaned as described under Cleaning and Maintenance.

3. Only recommended parts should be used. Unapproved parts may be

dangerous and will invalidate the warranty.

4. DO NOT attempt to repair a damaged heater, contact the Clarke service

department.

POSITIONING

1. This heater is designed for indoor use only.

2. DO NOT use this heater in small rooms when they are occupied by persons

not capable of leaving the room on their own unless constant supervision is

provided.

3. DO NOT use this heater in the immediate surrounds of a bath, a shower, a

swimming pool or wet surfaces.

4. NEVER place the heater against or near any surface such as a wall, door,

curtains, furniture or combustible material etc. Allow at least 2 metre

clearance.

5. DO NOT place the heater immediately below any electrical outlet.

6. DO NOT place the heater on a raised surface or anywhere where it could

topple over. ALWAYS use on a horizontal and stable surface.

7. ALWAYS ensure that the grille cannot be blocked.

8. DO NOT operate fan heaters in explosive atmospheres such as in the

presence of flammable liquids, gasses or dust such as in a paint spray

booth or any explosive environment. Electric motors create sparks which

may ignite dust or fumes.

WARNING: SERVICING OR INTERNAL MAINTENANCE MUST ONLY BE

CARRIED OUT BY THE CLARKE SERVICE DEPARTMENT.

WARNING: DO NOT USE THE HEATER NEAR FLAMMABLE MATERIAL,

LIQUIDS, SOLIDS, GASSES OR COMPRESSED GAS CYLINDERS ETC.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OPERATION

1. This heater is intended for drying & warming of commercial/industrial

buildings where adequate ventilation is provided. It is NOT for domestic use

or for heating habitable areas.

2. The heater should NOT be used by children or persons with reduced

physical, sensory or mental capabilities, or lack of experience and

knowledge.

3. CAUTION: Some parts of this product can become very hot and cause

burns. Particular attention should be given where, animals, children and

vulnerable people are present.

4. The heater must only be used by people who have read these instructions

and have been trained in its use.

5. DO NOT use if dropped.

6. DO NOT use if there is visible signs of damage.

7. DO NOT obstruct the air inlet and outlet sections of the heater.

8. DO NOT cover the heater with anything that could restrict the air flow.

9. DO NOT touch the heater casing or grille when first switched off, as these

will be very hot and will take time to cool.

10. DO NOT get the heater wet or use in areas of high condensation.

11. DO NOT allow the power lead to touch hot surfaces.

12. DO NOT connect other appliances to the same mains socket as the heater.

13. DO NOT use this heater with a programmable timer used to switch it on

automatically.

14. DO NOT leave the heater unattended.

SERVICE & REPAIRS

1. If necessary, have your heater repaired by a qualified person using

identical replacement parts. This will ensure that the safety of the product is

maintained.

2. Please keep these instructions in a safe place for future reference.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ELECTRICAL CONNECTIONS

This machine MUST be connected to a 400 Volt, 3 phase 50Hz supply through a

suitably rated isolator switch. It cannot be operated from a single phase

supply.

The user should purchase a suitable connecting cable capable of handling 63

Amps (recommended Cross Sectional Area 10mm2) and supply plug rated at

63A (or better) which complies with BSEN 60309. A length of 2-3 metres is

recommended giving mobility to the appliance but without becoming a trip

hazard

If in any doubt, consult a qualified electrician. DO NOT attempt any electrical

work yourself.

SAFETY SYSTEMS

THERMOSTATIC PROTECTION

The Devil 7030 has a manual reset thermal cut out to prevent the unit from

overheating.

If the thermal cut out activates, then turn off the power and disconnect from

the power supply. Allow the heater to cool down for several minutes before

pressing the reset button. Reconnect to the power supply and turn on to

resume operation.

LIST OF CONTENTS

WARNING: THE INSTALLATION OF THIS APPLIANCE SHOULD BE CARRIED

OUT BY A COMPETENT ELECTRICIAN AND BE IN ACCORDANCE WITH THE

CURRENT IEE WIRING REGULATIONS (BS7671-2:2008).

1 x Heater 1 x Axle c/w Circlip (2)

1 x R/H & 1 x L/H Support Frames 2 x Wheel

1 x Upper Handle 1 x Fixings Pack

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ASSEMBLY

1. Fit the right leg frame to the main

body as shown.

NOTE: The bolt needs to be inserted

before the handwheel.

NOTE: The bolt goes through the

larger of the 2 holes in the

spacer.

2. Fit the axle and left hand support

frame.

NOTE: The circlip shown must be on

the inside of the legs.

3. Fit the wheels as shown.

NOTE: The cap fits over the flat

washer.

4. Use the nuts and bolts supplied, to

secure the handle to the leg

frames as shown.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OPERATION

1. Put the heater in a level position on a flat surface and at a safe distance

from flammable materials. Keep a minimum of 2m clearance all round.

2. Connect the heater to a suitable

power supply.

3. Set the thermostat control to the

maximum setting (fully clockwise).

4. Set the mode selector to one of

the 3 settings:

• The heater will take up to three minutes to reach optimum temperature.

5. Once the room reaches the required temperature, turn the thermostat

control slowly counter-clockwise until the thermostat clicks, leave the

control in this position.

• The room temperature will be maintained at this setting. The heater will

continue to operate until the power switch is turned to the OFF position.

WARNING: DO NOT USE THIS HEATER IN SMALL ROOMS WHEN THEY ARE

OCCUPIED BY PERSONS NOT CAPABLE OF LEAVING THE ROOM ON THEIR

OWN, UNLESS CONSTANT SUPERVISION IS PROVIDED.

CAUTION: SOME PARTS OF THIS PRODUCT CAN BECOME VERY HOT AND

CAUSE BURNS. PARTICULAR ATTENTION HAS TO BE GIVEN WHERE

CHILDREN AND VULNERABLE PEOPLE ARE PRESENT.

Off

Fan Only

Fan + Heat Setting 1

Fan + Heat Setting 2

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

6. For fan only operation, turn the power switch to the fan only setting and set

the thermostat to its minimum setting.

7. Turn the heater off by turning the power switch to “0”,

• Do not remove the plug from the mains supply. The fan will continue to

run for several minutes to lower the temperature of the case and

elements. Once the fan stops you can safely remove the plug from the

power supply.

8. When not in use, disconnect the heater from the mains supply. Store it in a

safe, dry, childproof location.

MAINTENANCE

• Clean the heater with a soft damp cloth, Do not use solvents or

abrasives.

• Make sure that the heater grill is not blocked.

• No other maintenance is required, should you discover any problem

with the heater, return it to the Clarke service department for repair.

WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY AND ALLOW

THE HEATER IT TO COOL DOWN BEFORE PERFORMING ANY

MAINTENANCE TASKS.

Otros manuales para DEVIL 7030

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Calentador de Clarke

Clarke

Clarke DEVIL 6025 Manual de instrucciones

Clarke

Clarke DEVIL 340 Manual de instrucciones

Clarke

Clarke 6933990 Manual de instrucciones

Clarke

Clarke DEVIL 4035 Manual de instalación y operación

Clarke

Clarke Devil 6003 Manual de instrucciones

Clarke

Clarke DEVIL 2800PTC Manual de instrucciones

Clarke

Clarke XR80 Manual de instrucciones

Clarke

Clarke OFR7 Manual de instrucciones

Clarke

Clarke Devil 355MD Instrucciones de funcionamiento

Clarke

Clarke CFI 1800 Manual de instrucciones

Clarke

Clarke DEVIL 2800PTC-B Manual de instrucciones

Clarke

Clarke XR55 Manual de instalación y operación

Clarke

Clarke DEVIL 371SPC Manual de instalación y operación

Clarke

Clarke CONTRACTOR DEVIL371PD Manual de instalación y operación

Clarke

Clarke DEVIL 4035 Manual de instalación y operación

Clarke

Clarke DEVIL 2000PTC Manual de instrucciones

Clarke

Clarke DEVIL155 Manual

Clarke

Clarke OFR13/250 Manual de instrucciones

Clarke

Clarke DEVIL 370SPD Manual de instalación y operación

Clarke

Clarke DEVIL 4040 Manual de instrucciones

Clarke

Clarke DEVIL 5000PTC Manual de instrucciones

Clarke

Clarke BR13/250 Manual de instrucciones

Clarke

Clarke XRV100 Guía de solución de problemas

Clarke

Clarke Devil 370B Series Manual de instalación y operación

Manuales populares de Calentador de otras marcas

oventrop

oventrop Regucor Series Manual de usuario

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manual de usuario

ELMEKO

ELMEKO ML 150 Manual de usuario

BN Thermic

BN Thermic 830T Manual de usuario

KING

KING K Series Guía

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guía de inicio rápido

Well Straler

Well Straler RC-16B Manual de usuario

EUROM

EUROM 333299 Manual de usuario

Heylo

Heylo K 170 Manual de usuario

Eterna

Eterna TR70W Manual de usuario

IRSAP

IRSAP The Radiator Company Ovali Manual de usuario

Empire Heating Systems

Empire Heating Systems WCC65 Manual de usuario

Wetekom

Wetekom 92 86 43 Manual de usuario

Desa

Desa SPC170-F Manual de usuario

Watlow

Watlow Watrod Electric Tubular Heaters Manual de usuario

Haverland

Haverland ECO-DRY GPS Series Manual de lista de piezas

Stelpro

Stelpro ASILVC2060 Series Manual de usuario

iLO

iLO IHP2424 Manual de funcionamiento