Kramer SID-X1N Manual de usuario

SID-X1N Quick Start

P/N:

2900- 301222QS

Rev:

Scan for full manual

SID-X1N Quick Start Guide

This guide helps you install and use your SID-X1N for the first time.

Go to www.kramerav.com/downloads/SID-X1N to download the latest user manual and check if firmware

upgrades are available.

Step 1: Check what’s in the box

SID-X1N Step-in Commander

1 Set of rack ears

1 Power adapter (12V DC output)

1 Power cord

IMPORTANT NOTICE!

We highly recommend using only Kramer UNIKAT cables with these products. If using 3rd party shielded CAT-6A cables, both ends of the

shield must be soldered to the connectors for the products to function properly. Do not use any jumpers, unshielded wall plates or mid-

span cable connections. These extenders are not compatible with HDBaseT technologies. Prior to signal extension, ensure that the

extension line cable is lying straight and not coiled.

Step 2: Get to know your SID-X1N

Feature

Function

AUDIO IN 3.5mm Mini Jack

Connect to an unbalanced stereo audio source

HDMI

LED

Lights green when the HDMI input is selected

HDMI Connector

Connect to an HDMI source

DisplayPort

LED

Lights green when the DisplayPort input is selected

DP Connector

Connect to a DisplayPort source

DVI

LED

Lights green when the DVI input is selected

DVI Connector

Connect to a DVI source

PC-UXGA

LED

Lights green when the PC-UXGA input is selected

PC-UXGA 15-pin HD

Connector (F)

Connect to a PC graphics source

INPUT SELECT Button

Press repeatedly to cycle through the inputs manually to select an input, (overrides

automatic selection).

Note: When the button is lit it is inactive and pressing the button will not activate the

input

STEP-IN Button

Press to activate the input on the switcher that the

SID-X1N is connected to

ON LED

Lights green when the device is powered on

The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.

Step 3: Mount SID-X1N

Install SID-X1N using one of the following methods:

•Attach the rubber feet and place the unit on a flat surface.

•Fasten a bracket (included) on each side of the unit and attach it to a flat surface

(see www.kramerav.com/downloads/SID-X1N).

•Mount the unit in a rack using the recommended rack adapter

(see www.kramerav.com/product/SID-X1N).

•Ensure that the environment (e.g., maximum ambient temperature &

air flow) is compatible for the device.

•Avoid uneven mechanical loading.

•Appropriate consideration of equipment nameplate ratings should be

used for avoiding overloading of the circuits.

•Reliable earthing of rack-mounted equipment should be maintained.

Step 4: Connect inputs and outputs

Always switch OFF the power on each device before connecting it to your SID-X1N.

To achieve specified extension distances, use the recommended Kramer cables available at www.kramerav.com/product/SID-X1N.

Using third-party cables may cause damage!

Step 5: Connect power

Connect the power cord to SID-X1N and plug it into the mains electricity.

Safety Instructions (See www.kramerav.com for updated safety information)

Caution:

•For products with relay terminals and GPI\O ports, please refer to the permitted rating for an external connection, located next to the

terminal or in the User Manual.

•There are no operator serviceable parts inside the unit.

Warning:

•Use only the power cord that is supplied with the unit.

•Disconnect the power and unplug the unit from the wall before installing.

Step 6: Set DIP-switches

Feature

Function

DIP-switch

Program

Enables firmware updates

On—Enable updating

Off—Disable updating

General audio control

Selects whether the analog audio is

embedded in the outputs

On—Use embedded audio for HDMI and DP; the

audio selection for DVI is selected by DIP-switch 3

Off—The HDMI, DVI and DP inputs use the analog

audio signal if a 3.5mm audio jack is inserted into

the analog audio input. If no jack is inserted, they

use their embedded audio signals

DVI audio control

(active only when DIP-

switch 2 is on)

Selects whether the analog audio is

embedded in the DVI signal

On—When switch #2 is on, the analog audio signal

is used with the DVI input

Off—When switch #2 is off, the embedded audio

signal is used in the DVI input

Video mode input

selection

Sets the video input selection mode to

either last connected or manual

On—Last connected

Off—Manual

Lock EDID

Locks the current EDID

On—Locked EDID

Off—Automatic EDID selection

Switching delay

Selects the time delay before switching

occurs when an input signal is lost.

Note: The delay is independent of the

input switching mode

When the input signal is lost but the cable is not

removed:

On—0.5 seconds

Off—10 seconds

When the cable is removed:

On—0.5 seconds

Off—3 seconds

Output disable delay

Sets the delay time between loss of the

input signal and output/PowerConnect

shutdown

On—1 minute

Off—15 minutes

Output Power Control

Enables/disables the output power when

the input signal is lost

On—Power is always on

Off—Power is disabled when input signal is lost

after delay set by DIP-switch 7

DIP-switch 2 must be set to ON to enable DIP-switch 3 to control the DVI audio mode selection.

Step 7: Operate SID-X1N

Optional: Lock the current EDID if required.

Step 8: Technical Specifications

INPUTS:

Video:

1 HDMI on an HDMI connector

1 DP on a DisplayPort connector

1 DVI-D on a DVI-I connector

1 VGA on a 15-pin HD (F) connector

Audio:

1 Unbalanced stereo audio on a 3.5mm mini jack

OUTPUTS:

1 TP on an RJ-45

1 Unbalanced stereo audio in a 3.5mm mini jack

PORTS:

1 RS-232 3-pin terminal block for programming

CONTROLS:

Front panel buttons, remote step-in switch, remote input selection switches, RS-232

ANALOG AUDIO INPUT:

Maximum level—3Vpp

REMOTE LED IMPEDANCE:

5V, 300Ω approx.

STANDARDS:

HDMI with x.v.Color™ and 3D

HDCP: Works with sources that support HDCP repeater mode

MAXIMUM DATA RATE:

4.95Gbps (1.65Gb per graphics channel)

MAXIMUM STEP-IN DISTANCE:

50m (164ft) up to 1080p @60Hz @24bpp

POWER CONSUMPTION:

12V DC, 1.1A

COMPLIANCE STANDARDS:

CE, UL

OPERATING TEMPERATURE:

0° to +40°C (32° to 104°F)

STORAGE TEMPERATURE:

–40° to +70°C (–40° to 158°F)

HUMIDITY:

10% to 90%, RHL non-condensing

COOLING:

Convection, vents

ENCLOSURE TYPE:

Aluminum

DIMENSIONS:

18.8cm x 11.3cm x 2.5cm (7.4” x 4.5” x 1”) W, D, H rack-mountable

WEIGHT:

0.48kg (1.1lbs) approx.

INCLUDED ACCESSORIES:

Power adapter

Specifications are subject to change without notice

For the most updated resolution list, go to our Web site at www.kramerav.com

Otros manuales para SID-X1N

Otros manuales de Transmisor de Kramer

Kramer

Kramer TP-121EDID Manual de usuario

Kramer

Kramer TP-45EDID Manual de usuario

Kramer

Kramer DIP-20 Manual de usuario

Kramer

Kramer TP-114 Manual de usuario

Kramer

Kramer TP-580TD Manual de usuario

Kramer

Kramer TP-185 Manual de usuario

Kramer

Kramer 610T Manual de usuario

Kramer

Kramer 691 Manual de usuario

Kramer

Kramer TP-752T Manual de usuario

Kramer

Kramer TA Manual de usuario

Kramer

Kramer KW-14T Manual de usuario

Kramer

Kramer TP-205A Manual de usuario

Kramer

Kramer 610T Manual de usuario

Kramer

Kramer VP-300THD Manual de usuario

Kramer

Kramer 617T Manual de usuario

Kramer

Kramer TP-125 Manual de usuario

Kramer

Kramer VP-300THD Manual de usuario

Kramer

Kramer TP-590Txr Manual de usuario

Kramer

Kramer SID-X1 Manual de usuario

Kramer

Kramer TP-121EDID Manual de usuario

Kramer

Kramer TP-202 Manual de usuario

Kramer

Kramer Cobra TS2 Manual de usuario

Kramer

Kramer VP-200XLT Manual de usuario

Kramer

Kramer TP-210 Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario