Kamstrup READy MTU Instrucciones de funcionamiento

Kamstrup A/S • 55122662_C1_US_06.2020

READy MTU

Warning!

Read instructions before installation

Installation and operation guide

Installation & operation guide

Kamstrup A/S • 55122662_C1_US_06.20202

READy MTU

Disclaimer

All information provided in this document is copyright of Kamstrup. Licence is granted to the user to freely use and distribute

the information in complete and unaltered form, provided that the purpose is to use or evaluate Kamstrup products.

Distribution rights do not include public posting or mirroring on Internet websites. Only a link to the Kamstrup website can be

provided on such public websites.

Kamstrup shall in no event be liable to any party for direct, indirect, special, general, incidental, or consequential damages

arising from the use of this information or any derivative works thereof. The information is provided on an as-is basis, and thus

comes with absolutely no warranty, either express or implied. No right or licence is granted under any intellectual property

right, hereunder copyright, patent or trademark, of Kamstrup to any other party. This disclaimer includes, but is not limited to,

implied warranties of merchantability, ﬁtness for any particular purpose, and non-infringement.

Information in this document is subject to change without notice and should not be construed as a commitment by

Kamstrup. While the information contained herein is believed to be accurate, Kamstrup assumes no responsibility for any

errors and/or omissions that may appear in this document.

Industrivej 28

Stilling

DK-8660 Skanderborg, Denmark

The graphics and content in this document are the copyrighted work of Kamstrup and contain proprietary trademarks and

trade names of Kamstrup.

Third parties

This document may contain links to other parties. Kamstrup makes no warranty or representation regarding any linked

information appearing therein. Such links do not constitute an endorsement by Kamstrup of any such information and are

provided only as a convenience. Kamstrup is not responsible for the content or links displayed by third parties.

Installation & operation guide

Kamstrup A/S • 55122662_C1_US_06.2020 3

READy MTU

Contents

1 Symbols used in this document 4

1.1 Warnings in this document 4

2 Abbreviations 6

3 FCC caution 6

4 Canadian compliance statement 6

5 Technical data 7

5.1 Product introduction 7

5.2 System overview 7

5.3 Electrical data 7

5.4 Mechanical data 7

5.5 Material 8

5.6 Communication 8

5.7 Transmission interval 8

5.8 Input 8

5.9 Data security 8

6 Before you begin 8

6.1 Precautions 8

6.2 What is in the box 9

6.3 Accessories 9

6.4 Deployment process summary 9

7 Before ﬁeld deployment 9

7.1 Import READy MTU from Kamstrup Encryption Key Service 9

7.2 Import non-Kamstrup meters and customer information in READy Manager 9

7.3 Create a group of non-Kamstrup meters for READy MTU installation 10

7.4 MTU modes and LED blinking scheme 10

8 Field deployment 11

8.1 Installation 11

8.2 Conﬁguration of READy MTU 14

8.3 Default or preconﬁgured 14

9 Operation 21

9.1 Normal operation 21

9.2 Alarms/info codes 21

9.3 Device exchanges 22

9.4 Fallback and log readings 23

9.5 Reconﬁguration 23

9.6 Decommissioning 26

9.7 Kamstrup support 28

10 Storage 28

11 Disposal 29

11.1 Disposal by Kamstrup A/S 29

11.2 The customer sends for disposal 29

11.3 Disposal by the customer 29

11.4 Instructions for disposal 29

12 Ordering details 30

12.1 Type number 30

12.2 US AMI MTU conﬁguration is described below: 30

12.3 Other MTU ordering data 31

12.4 Accessories 31

Installation & operation guide

Kamstrup A/S • 55122662_C1_US_06.20204

READy MTU

1 Symbols used in this document

Indicates a hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a hazardous situation which, if not avoided, could result in moderate injury, damage the product, or

lead to loss of data.

Indicates a hazardous situation which, if not avoided, may seriously impact operations.

1.1 Warnings in this document

Battery safety:

Fire, explosion and severe burn hazard.

Please follow these guidelines in order to avoid injury to yourself and others:

• If not disposed of properly, the battery may cause ﬁre or chemical burn

• Do NOT recharge, disassemble, crush, expose to water, heat above 212 °Fahrenheit (100 °Celsius), or

incinerate the battery

• Keep away from children

Must be installed to provide a separation distance of at least 20 cm from all persons.

The contents of this guide and the quick guide included with the device must be followed at all times when

installing, conﬁguring or handling the device in general. If this guide is not followed, Kamstrup cannot be held

accountable for any malfunctions or misuse of the product.

Do not install outside Lightning Protection Zone 0C. 10 ft/3 m height and depth around the building.

Use only approved accessories with this device. Unapproved modiﬁcations or operation beyond or in conﬂict with

these instructions for use may void authorization by the authorities to operate the device.

Ensure that READy MTU is in transport mode when transported by air freight or during decommissioning.

Ensure proper disposal of the product.

Do not disassemble the product as the IP68 sealing will be void, and do not tamper with the internal battery and

electronics.

READy MTU is designed to operate at temperatures of -30 °C…65 °C (-22 °F…149 °F). Using the device outside the

intended operating temperature range may cause deterioration of battery life or in worst case operating failure.

Must NOT be co-located in conjunction with any other antenna or transmitter.

Do not try to modify or repair the device. Attempts to modify or repair will void the warranty.

Ensure that READy App and READy Manager are synchronized before you proceed with the installation.

Installation & operation guide

Kamstrup A/S • 55122662_C1_US_06.2020 5

READy MTU

Read the guide prior to installation and taking the device into use.

The product may only be installed by trained personnel.

Wire terminations must be properly sealed with a non-conductive gel material to prevent water intrusion

(otherwise, this conﬁguration should not be used in a pit environment).

Kamstrup does not recommend using gel connectors in pit environments.

Kamstrup recommends mounting READy MTU in/under non-metallic meter pit lids only. If installing under metal

lids, make sure to use the pit antenna.

Mount READy MTU as high as possible in the pit, without the antenna being in contact with the pit lid.

Mount READy MTU as high as possible. The MTU should be mounted at or above ground level. Mount READy MTU

as high as possible. The MTU should be mounted at or above ground level.

Always install READy MTU in the protection cover (accessory) when the device is installed in sun-exposed areas.

Mount READy MTU at least 6 inches away from any metal objects, including pipes, conduit, and downspouts.

When mounting multiple MTUs in the same location, leave at least 4 inches between the MTUs if mounting side

by side and at least 3 inches between MTUs if mounting one above another.

Do not mount READy MTU so that it is transmitting towards a nearby building or fence.

Do not mount READy MTU directly under AC power or telecommunications wires.

Mount READy MTU as high as possible near an exterior wall. The MTU should be mounted at or above grade

(ground level).

Mount READy MTU at least 6 inches away from pipes and conduit and several inches below the ceiling.

Mount READy MTU at least 5 feet away from any large metal objects. (e.g. refrigerators, HVAC ducts, furnaces,

and hot water heaters).

Do not mount READy MTU in a basement with a metal ceiling.

Do not mount READy MTU directly under AC power wires, circuit breaker panels, or telecommunications wires.

Installation & operation guide

Kamstrup A/S • 55122662_C1_US_06.20206

READy MTU

2 Abbreviations

MTU: meter transmission unit

LPZ: Lightning Protection Zone

MDM: meter data management

EO: encoded output

CIS: customer information system

3 FCC caution

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or Kamstrup for help

4 Canadian compliance statement

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two

conditions:

(1) This device may not cause interference, and

(2) This device must accept any interference, including interference that may cause undesired operation of the device.

Cet appareil est conforme aux normes CNR exemptes de licence d’Industrie Canada. Le fonctionnement est soumis aux deux

conditions suivantes:

(1) Cet appareil ne doit pas provoquer d’interférences et

(2) Cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer un fonctionnement non souhaité

de l’appareil.

Complies with the Canadian ICES-003 Class B speciﬁcations.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

This device complies with RSS 247 of Industry Canada. This Class B device meets all the requirements of the Canadian

interference-causing equipment regulations.

Cet appareil est conforme à la norme canadienne RSS 247. Cet appareil numérique de la Classe B respecte toutes les

exigences du Règlement sur le matériel brouilleur du Canada.

Installation & operation guide

Kamstrup A/S • 55122662_C1_US_06.2020 7

READy MTU

5 Technical data

5.1 Product introduction

READy MTU is a one-to-one meter data transmission unit that connects to meters utilizing the Sensus UI1203 Encoded Output

protocol. Data from READy MTU is forwarded to the READy Manager MDM system via Kamstrup’s AMI system.

5.2 System overview

READy MTU connects to an encoded output meter and sends data to READy Collector and READy Manager.

5.3 Electrical data

Battery safety:

Fire, explosion and severe burn hazard.

Please follow these guidelines in order to avoid injury to yourself and others:

• If not disposed of properly, the battery may cause ﬁre or chemical burn

• Do NOT recharge, disassemble, crush, expose to water, heat above 212 °Fahrenheit (100 °Celsius), or

incinerate the battery

• Keep away from children

Do not disassemble the product as the IP68 sealing will be void, and do not tamper with the internal battery and

electronics.

Battery D-cell battery

Battery liftetime Up to 20 years at tBAT < 40 °F

Up to 16 years at tBAT < 55 °F

Up to 8 years at tBAT < 130 °F

5.4 Mechanical data

READy MTU is designed to operate at temperatures of -30 °C…65 °C (-22 °F…149 °F). Using the device outside the

intended operating temperature range may cause deterioration of battery life or in worst case operating failure.

Protection class IP68 rated (waterproof/submersible)

Weight Approx. 525 g / 1.15 Lbs incl. stub antenna

Dimensions Ø 91.6 mm x 106 mm (Ø 3.6” x 4.2”)

Ø 91.6 mm x 149.8 mm (Ø 3.6” x 5.9”) incl. antenna

Installation & operation guide

Kamstrup A/S • 55122662_C1_US_06.20208

READy MTU

5.5 Material

Housing Polyphenylene sulﬁde (PPS) with ﬁberglass (40 %) reinforcement

Top ring Polycarbonate (grey)

5.6 Communication

Wireless fallback reading

and conﬁguration 902 MHz – 928 MHz (license free)

Kamstrup AMI 450 – 470 MHz (FCC licensed)

Antenna External

Magnet sensor Activation of MTU radio and installation mode

5.7 Transmission interval

Must be installed to provide a separation distance of at minimum 20 cm from all persons.

Must NOT be co-located in conjunction with any other antenna or transmitter.

Meter reading interval Hourly top of the hour

Transmission Every 3 hours

5.8 Input

Single meter/register input Sensus UI-1203 3-wire encoded

Wire length 5 ft Nicor/Itron/ﬂying wire

5.9 Data security

READy MTU is part of the complete end-to-end data encryption of the READy suite.

Data is AES 128 bit end-to-end encrypted when in transit from READy MTU to READy Manager.

6 Before you begin

6.1 Precautions

The contents of this guide and the guide included with the device must be followed at all times when installing,

conﬁguring or handling the device in general. If this guide is not followed, Kamstrup cannot be held accountable

for any malfunctions or misuse of the product.

Do not try to modify or repair the device. Attempts to modify or repair will void the warranty.

Ensure that READy App and READy Manager are synchronized before you proceed with the installation.

Read the guide prior to installation and taking the device into use.

The product may only be installed by trained personnel.

NOTE: Kamstrup recommends using READy Bluetooth optical read-out head to activate the magnet sensor of READy MTU.

Magnet power 8.6 lbs/3.9 kg (N35).

Installation & operation guide

Kamstrup A/S • 55122662_C1_US_06.2020 9

READy MTU

6.2 What is in the box

The content of the box depends on the chosen accessories:

• READy MTU

• MTU mounting screw

• Quick guide

6.3 Accessories

READy MTU can be ordered with the following accessories:

• 5 ft cable with ﬂying wire, Nicor or Itron plug

• Wall antenna (packed separately)

• External stub antenna

• 3” pit antenna for installation in pit lids (packed separately)

• Wall/pit bracket

• Protection cover for installation in sun-exposed areas (packed separately)

Dimensions: 198 mm x 166 mm x 114 mm (7.8” x 6.5” x 4.5”)

6.4 Deployment process summary

1. Before ﬁeld deployment

- Import READy MTU(s) in READy Manager

- Import non-Kamstrup meters and customer information (optional)

- Create a group containing non-Kamstrup meters that will be retroﬁtted with READy MTU

- Charge READy Converter and mobile device

2. Field deployment of default or preconﬁgured MTU

a. Default conﬁgured MTU: install, activate, and conﬁgure READy MTU using READy App and READy Converter

b. Preconﬁgured MTU: install and activate READy MTU. No additional conﬁguration is required

3. The installation and conﬁguration are complete

7 Before ﬁeld deployment

Before ﬁeld deployment, make sure that your READy Manager system is prepared for collecting data from encoded meters via

READy MTU by following the steps in this section.

7.1 Import READy MTU from Kamstrup Encryption Key Service

READy MTU is automatically imported into READy Manager if you are logged in with your My Kamstrup account and the Import

new devices checkbox is ticked.

If not logged in, you can import READy MTUs directly from Kamstrup Encryption Key Service found in My Kamstrup.

Click the Import devices button on the start-up page of READy Manager.

More information can be found in the READy Manager guide under Automatically importing information for new devices or

Manually importing information for new devices.

7.2 Import non-Kamstrup meters and customer information in READy Manager

Kamstrup recommends that you import the ID/serial number that is sent on the encoded output as the meter

serial number in READy Manager. If not, you are required to overwrite the serial number of the encoded output

with the serial number imported in READy Manager for your speciﬁc device.

Import non-Kamstrup meters and customer information in READy Manager by selecting Import customers on the start-up

page of READy Manager.

More information on CIS import can be found in the READy Manager guide under Automatically importing customer data or

Manually importing customer data.

Installation & operation guide

Kamstrup A/S • 55122662_C1_US_06.202010

READy MTU

7.3 Create a group of non-Kamstrup meters for READy MTU installation

It is recommended to create a group of non-Kamstrup meters that will be retroﬁtted with READy MTU that can be synced with

READy App.

Create a group:

1. Select the Meters view in READy Manager.

2. Select New group. Name the group.

3. Select the meters that are to be part of the group and add the meters to the group.

Find more information in the READy Manager guide under Organizing meters in reading groups.

7.4 MTU modes and LED blinking scheme

7.4.1 MTU modes

7.4.1.1 Transport mode

When you receive READy MTU, the device is in transport mode. In transport mode, the radio is deactivated. The magnet sensor

for activating the MTU is active.

By inﬂuencing the magnet sensor for 3 seconds, the LED on the front of READy MTU turns on. The MTU checks if a meter is

connected on the encoded interface before turning on the radio. If no meter is connected, READy MTU remains in transport

mode.

Remember to enable transport mode when decommissioning READy MTU. See section 9.6 Decommissioning.

7.4.1.2 Installation mode

After activation, READy MTU starts up in installation mode. The LED turns on and a connection beacon is sent out every 4

seconds.

Installation mode is active for 5 minutes after activation.

After the installation mode period has ended, READy MTU enters normal mode.

When operating in normal mode, installation mode can be triggered by holding the magnet to the front of READy MTU. This will

also reactivate the LED.

7.4.1.3 Operation mode

In operation mode, READy MTU can at all times be accessed via READy App. A connection beacon is sent every 30 seconds

during normal operation. The LED is not active in normal mode.

7.4.2 LED blinking scheme

1 time every 5 seconds Everything is OK.

READy MTU is reading the encoded output and sending data

via AMI.

3 times every 5 seconds Something is wrong.

READy MTU is not reading the encoded output or sending

data via AMI.

5 s5 s

Tabla de contenidos

Otros manuales de Transmisor de Kamstrup

Kamstrup

Kamstrup ULTRAFLOW 14 Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario

Excalibur

Excalibur SoundMaster FM Transmitter 144 Manual de usuario