Jbc AL-A Series Manual de usuario

INSTRUCTION MANUAL

AL-A

Auto-Feed Soldering Station

Packing List

The following items are included:

Metal Brush ................... 1 unit

Ref. CL6217

Auto-Feed Iron ............. 1 unit

Ref. AL250-B

Includes: Cartridge C250403 and

Cartridge Guide Ref. 0002401

(Ø 0.9 - 1 mm / 0.035 - 0.04 in)

Stand ............................... 1 unit

R e f . A L- SF

Power Cord .................... 1 unit

Ref. 0023715 (120V)

0023714 (230V)

0024092 (100V)

Sponge ........................... 1 unit

Ref. S0354

Manual ............................ 1 unit

Ref. 0020485

Solder Reel Stand ....... 1 unit

R ef. 0 0 874 5

Auto-Feed

Soldering Station ......... 1 unit

Manual Tip Cleaner ..... 1 unit

Ref. CL8499

Allen Key 2.5mm .......... 1 unit

Ref. 0780493

This manual corresponds to the following references:

- AL-1A (120V )

- AL-2A (230V)

- AL-9A (100V)

2

Features and Connections

Stand

R e f . A L- S F

Power

Socket

Equipotential

Connection

Pedal

Connection

(optional)

Auto-Feed Iron

Ref. AL250-B

Fuse

Main Switch

www.jbctools.com

3

Guide Set

1

2

2

Reel Stand Assembly

Adjusting System Assembly

4

4

3

2

1

1. Assemble the Reel Stand to the Station

2. Tighten the screws.

1. Open the dragging mechanism moving the lever downwards (the dragging mechanism releases

the solder wire).

2. Place the guide set and tighten the screws.

3. Assemble the Solder Reel

4. Tighten the screws.

Dragging Mechanism

4

4

3. Take the solder wire from the reel until the guide tube start.

4. Close the dragging mechanism moving the lever upwards (the dragging mechanism

moves toward the Solder wire).

Guide Tube

Start

3

Dragging Mechanism

www.jbctools.com

5

LOADING

SOLDER WIRE

--

++

++

--

A

B

5. Connect the handpiece to the station and switch the station on. With the handpiece out of the

stand, press the WIRE LOAD key at the station till the solder wire comes out at the guide tube end.

Fast Wire Dragging

Solder Wire Dragging Button

A. Adjust the dragging strength to enable the solder wire to be passed on properly and to

avoid any jamming or clogging.

B. Fix the dragging mechanism by tighten more or less the sprung element.

Clutch Regulation

6

between 5 and 300 units

(1 unit = 0.1 mm/sec / 0.039 in/sec)

Control Screen

There are 4 tool status:

USE (Use). The tool is ready to work.

STD (Stand). The tool is placed in the stand but still not in the sleep mode.

SLP (Sleep). The tool is in the sleep mode in the stand, its temperature has dropped till

the sleep temperature.

OL. The power circuit is overheated. The power is temporarily not supplied.

TEMP. 230ºC USE

disc. L 10 S 11

Tool Temperature Tool Status

Wire Lengthw SpeedWorking Method

Troubleshooting

Station troubleshooting available on the product page at www.jbctools.com

www.jbctools.com

7

between 5 and 300 units*

300 units*

between 5 and 300 units*

units*

* (1 unit = 0.1 mm/sec / 0.039 in/sec)

Parameters Modification of the Tool and the Station

To enter into this mode, you must hold the SELECT key for 3 seconds.

8

between 5 and 300 units*

300 units*

between 5 and 300 units*

units*

* (1 unit = 0.1 mm/sec / 0.039 in/sec)

www.jbctools.com

9

Clean periodically

Before carrying out maintenance, always switch the device off and disconnect it from the mains.

Allow the equipment to cool down.

- Clean the station screen with a glass

cleaner or a damp cloth.

- Use a damp cloth to clean the casing and

the tool. Alcohol can only be used to clean

the metal parts.

- Periodically check that the metal parts

of the tool and stand are clean so that the

station can detect the tool status.

- Maintain tip surface clean and tinned prior

to storage in order to avoid tip oxidation.

Rusty and dirty surfaces reduce heat transfer

to the solder joint.

- Periodically check all cables and tubes.

- Replace a blown fuse as follows:

Maintenance

1. Pull off the fuse holder and remove the

fuse. If necessary use a tool to lever it off.

2. Insert the new fuse into the fuse holder

and return it to the station.

- Replace any defective or damaged pieces. Only use original JBC spare parts.

- Repairs should only be performed by a JBC authorized technical service.

Fuse Holder

10

Otros manuales para AL-A Series

1

Este manual sirve para los siguientes modelos

3

Tabla de contenidos

Manuales populares de Pistola de soldar de otras marcas

Bakon

Bakon 3200 Manual de usuario

Proxxon

Proxxon Gaslotset MGS Manual de usuario

HAKO

HAKO FX-8804 Manual de usuario

SATA

SATA 02002A Manual de usuario

Velleman

Velleman HRJA151 Manual de usuario

Weller

Weller WSM 1 Manual de usuario

Vishay Precision Group

Vishay Precision Group Micro-Measurements Mark V Instrucciones de montaje

ersa

ersa i-CON 1V Manual de usuario

Hakko Electronics

Hakko Electronics FX-100 Manual de usuario

Weller

Weller WAD 101 Manual de usuario

Weller

Weller WXD 2 Manual de usuario

AlienTek

AlienTek T100 Manual de usuario

Atten

Atten ATETOOL AT-689A Manual de usuario

Surtek

Surtek 112554 Dimensiones y guía de instalación

Parkside

Parkside PLBS 30 A1 Manual de usuario

BlackJack SolderWerks

BlackJack SolderWerks BK8000 Manual de usuario

Weller

Weller WX1 Manual de usuario

multicomp pro

multicomp pro MP740893 Manual de usuario