Intermec PM4I Manual de usuario

Otros manuales para PM4I

18

Este manual sirve para los siguientes modelos

1

Tabla de contenidos

Otros manuales de Accesorios de impresora de Intermec

Intermec

Intermec EasyCoder PF2i Manual de usuario

Intermec

Intermec EasyCoder 601XP Manual de usuario

Intermec

Intermec EasyCoder PF4ci Manual de usuario

Intermec

Intermec PB2 Series Manual

Intermec

Intermec Font Card Manual de usuario

Intermec

Intermec PB50 Manual de usuario

Intermec

Intermec EasyCoder 501 SA Manual de usuario

Intermec

Intermec EasyCoder 601XP Manual de usuario

Intermec

Intermec PM4I Manual de usuario

Intermec

Intermec EasyCoder PF2i Manual de usuario

Intermec

Intermec 4820 Guía de inicio rápido

Intermec

Intermec EasyCoder 201II Manual del propietario

Intermec

Intermec EasyCoder 3400e Manual de usuario

Intermec

Intermec PB41 Manual de usuario

Intermec

Intermec EasyCoder 3400e Manual de usuario

Intermec

Intermec EasyCoder 501 E Manual de usuario

Intermec

Intermec EasyCoder F2 Manual de usuario

Intermec

Intermec ESim v4.20 Manual de usuario

Intermec

Intermec EasyCoder PD4 Manual de usuario

Intermec

Intermec EasyCoder PF2i Manual de usuario

Intermec

Intermec PB50 Manual de usuario

Intermec

Intermec PM4I Manual de usuario

Intermec

Intermec EasyCoder 501 SA Manual de usuario

Intermec

Intermec EasyCoder 501XP Manual de usuario

Manuales populares de Accesorios de impresora de otras marcas

Star Micronics

Star Micronics TSP800 Series Manual de usuario

REA

REA JET HR pro 2K Manual de usuario

HP

HP Laserjet,Color Laserjet 4si Manual de usuario

oliser

oliser MS 45 Manual de usuario

Roland

Roland DU2-64 Instrucciones y recetas

Xerox

Xerox EFI EXP6000 Manual de usuario

Canon

Canon Finisher-T1 Manual de usuario

Sharp

Sharp FO-1MK Manual de usuario

Labelmate

Labelmate PM-300 Manual de usuario

Epson

Epson T6248 Manual de funcionamiento

Epson

Epson OT-BZ20 Manual de usuario

Canon

Canon TonerRobot EP-27 Manual de usuario

Ricoh

Ricoh LCIT RT5100 Guía de inicio rápido

GBC

GBC 16 Series Manual de usuario

Canon

Canon INNER 2-WAY TRAY-E1 Manual de operación y mantenimiento

Develop

Develop SD-509 Manual de usuario

Kyocera

Kyocera KM-6230 Manual

Triumph Adler

Triumph Adler DF-710 Manual

Use these installation instructions to replace the power supply unit (PSU) on

the PM4i printer. The PSU kit ships with these items:

•Power supply unit (P/N 1-971131-003)

•This installation instruction sheet

To install the power supply unit, you need:

•T20 Torx screwdriver

To install the power supply unit

1Turn off the printer power and remove the power cord.

2Lay the printer on its left cover (the electronics and front cover).

PM4i

This installation procedure must only be performed by an

authorized Intermec service technician. Intermec assumes no

responsibility for personal injury or damage to the

equipment if the installation is performed by an

unauthorized person.

The electrical components in the printer are susceptible to

damage from electrostatic discharge (ESD). You must

follow standard ESD guidelines to avoid damaging the

equipment you are servicing.

Power Supply Unit Installation Instructions

3Remove the four T20 Torx screws from the bottom of the printer and then set

the printer back upright.

4Open the media cover and remove the four T20 Torx screws that attach the

electronics and front cover to the printer.

Screw

(4 places)

Screw

(4 places)

5Lift the electronics and front cover door away from the printer and carefully

disconnect the console cable from the CPU board.

6Disconnect all of the cables from the CPU board.

7Remove the four T20 Torx screws and the standoff that attach the CPU board to

the power supply unit and lift it away from the printer.

Screw

(4 places)

Worldwide Headquarters

6001 36th Avenue West

Everett, Washington 98203

U.S.A.

tel 425.348.2600

fax 425.355.9551

www.intermec.com

© 2009 Intermec Technologies

Corporation. All rights reserved.

PM4i Power Supply Unit Installation Instructions

*931-067-001*

P/N 931-067-001

8Remove the six T20 Torx screws that attach the power supply unit to the printer,

disconnect the cables from it, and lift it away from the printer.

9To replace the power supply unit, reverse Steps 1 through 8. You need to reuse

the ground (GND) cable (P/N 236-068-003) and the cooling plate

(P/N 1-206170-00).

Note: When you remove the screws that attach the power supply unit to

the printer, the rear panel of the printer will detach.

Note: Make sure that you attach the GND cable through the lower left

screw when you replace the power supply unit.

Screw

(6 places)

Ground

cable