Intermec EasyCoder F2 Manual de usuario
EasyCoder F-Series
IEEE 1284 Parallel Interface Board
P/N 1-960473-01
Edition 2
January 2001
Installation Instructions
1
EasyCoder F-Series IEEE 1284 Parallel Interface Board – Installation Instructions Ed. 2
Chapter 1
EasyCoder F-Series
IEEE 1284 Parallel Interface
Board
Installation Instructions
Edition 2, January 2001
Part No. 1-960473-01
Description
Application of Use
IEEE 1284 Interface
Installation Kit
The IEEE 1284 Parallel Interface Board is an optional device
for EasyCoder F2 and EasyCoder F4 which provides these
printers with an parallel interface port.
The parallel communication port is addressed in Intermec Fin-
gerprint v7.2 or later as device "centronics:". The board is
IEEE1284-I compatible. Nibble, byte, ECP, and EPP modes
from printer to host are not presently supported.
The IEEE 1284 board has a standard 36-pin female IEEE
1284B connector with the following configuration:
Pin Signal Pin Signal
1 DSTROBE 19 GND
2 DATA 0 20 GND
3 DATA 1 21 GND
4 DATA 2 22 GND
5 DATA 3 23 GND
6 DATA 4 24 GND
7 DATA 5 25 GND
8 DATA 6 26 GND
9 DATA 7 27 GND
10 ACK 28 GND
11 BUSY 29 GND
12 PE 30 GND
13 SELECT 31 INIT
14 AF 32 ERROR
15 N/C 33 N/C
16 GND 34 N/C
17 SCREEN 35 N/C
18 + 5V EXT (max 200 mA)1 36 SELECTIN
1/. The external 5V is automatically switched off at overload.
There are neither any straps or other types of physical con-
figuration on this interface board, nor any options in the Setup
Mode
The IEEE 1284 Parallel Interface Kit contains:
•One interface board.
•One flat cable
•This Installation Instruction booklet
.
EasyCoder F-Series IEEE 1284 Parallel Interface Board – Installation Instructions Ed.2
2
Chapter 2
EasyCoder F2 and F4
• Open the electronics compartment by removing the front/
left-hand cover, which is held by three #T20 Torx screws
from the media compartment side of the center section.
Warning!
Switch off the power and disconnect the power cord. The
electronics compartment contains high voltage components
and wires. Do not open the electronics compartment before
the printer is safely disconnected from any AC supply.
• Remove the two #T10 Torx screws that hold the interface
cover plate on the printer’s rear plate. Remove the cover
plate.
#T10 Torx screw
Cover Plate
#T10 Torx screw
#T20Torx screws (x3)
Installation
3
EasyCoder F-Series IEEE 1284 Parallel Interface Board –Installation Instructions Ed. 2
Chapter 2 Installation
EasyCoder F2 and F4,
cont.
•Save the cover plate for possible later use. Keep the
screws.
•Insert the interface board with the components side facing
right, as seen from behind.
•Attach the interface board to the printer’s rear plate by
means of the two screws left over when you removed the
original cover plate.
•Connect the flat cable included in the kit between connector
P81 on the CPU board and connector P1 on the interface
board (also see the next page.)
Interface
Board
P35
IC305
P32
IC304
P33
P81
P1
C9
C10
C11
C12
C13
D1
D2
IC2
IC4 IC3
IC5A
R1
R2
R3
R4
R5
R6
R7
R8
R9
R10
R11
R12
R13
R14
R15
R16
R17
R18
R19
R20
R21
R22
R23 R24
R25 R26
R27
R28
R29
R30
R31
R33
R34
R35
R36
R37
R38
R39
R40
R41
FV1
FV2 FV3
P3
L1
L2
L3
L4
L5
L6
L7
L8
L9
L10
L11
L12
L13
L14
L15
L16
L17
L18
L19
T1
1-971611-01.P01
C1
C2
C3
C4
C5 C6
C7
C8
IC1
C14
R32
P1
EasyCoder F-Series IEEE 1284 Parallel Interface Board –Installation Instructions Ed. 2
4
Chapter 2 Installation
EasyCoder F2 and F4,
cont.
•Make sure that the cable between CPU board and interface
board runs as illustrated below.
•Put back the front/left-hand cover.
•Connect the power cord.
•Now you have one new interface connector ("centronics:")
on the printer’s rear plate in addition to the standard inter-
faces "uart1:" and "usb1:". Connect the parallel interface
cable and switch on the power.
IEEE 1284 Interface
"centronics:"
Serial Interface
"uart1:"
CPU Board
Interface Board
Cable
Information in this manual is subject to change without prior notice and
does not represent a commitment on the part of Intermec Printer AB.
© Copyright Intermec Printer AB, 2001. All rights reserved. Published in
Sweden.
EasyCoder, EasyLAN, Fingerprint, and LabelShop are registered trade-
marks of Intermec Technologies Corp. The word Intermec, the Intermec
logo, InterDriver, and PrintSet are trademarks of Intermec Technologies
Corp.
Centronics is a registered trademark of Genicom Corp.
Torx is a registered trademark of Camcar Division of Textron Inc.
Serial Interface
"usb1:"
Otros manuales para EasyCoder F2
8
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Accesorios de impresora de Intermec
Intermec
Intermec CN3 Series Manual de usuario
Intermec
Intermec PW50 Manual de usuario
Intermec
Intermec Font Card Manual de usuario
Intermec
Intermec EasyCoder 3400e Manual de usuario
Intermec
Intermec 3240 Manual de usuario
Intermec
Intermec EasyCoder 601XP Manual de usuario
Intermec
Intermec 074788 Series Manual de usuario
Intermec
Intermec EasyCoder 3400e Manual de usuario
Intermec
Intermec EasyCoder PF2i Manual de usuario
Intermec
Intermec PB41 Manual de usuario
Intermec
Intermec 3600 Manual de usuario
Intermec
Intermec PA30 Manual de usuario
Intermec
Intermec EasyCoder 201II Manual del propietario
Intermec
Intermec EasyCoder 501XP Manual de usuario
Intermec
Intermec EasyCoder 201II Manual de usuario
Intermec
Intermec EasyCoder 501XP Manual de usuario
Intermec
Intermec EasyCoder 501 SA Manual de usuario
Intermec
Intermec EasyCoder PD4 Manual de usuario
Intermec
Intermec 3240 Manual de usuario
Intermec
Intermec EasyCoder 601XP Manual de usuario
