Intermec PM4I Manual de usuario
Installation
Instructions
Cutter Kit
(for EasyCoder PM4i)
Intermec Printer AB
Idrottsvägen 10
P.O. Box 123
S-431 22 Mölndal
Sweden
Service support: +46 31 869500
The information contained herein is proprietary and is provided solely
for the purpose of allowing customers to operate and/or service Intermec
manufactured equipment and is not to be released, reproduced, or used
for any other purpose without written permission of Intermec.
Information and specifications in this manual are subject to change
without notice.
© 2003 by Intermec Printer AB
All Rights Reserved
EasyCoder and Fingerprint are registered trademarks of Intermec Tech-
nologies Corp. The word Intermec and the Intermec logo are trademarks
of Intermec Technologies Corp.
Torx is a registered trademark of Camcar Division of Textron Inc.
Throughout this manual, trademarked names may be used. Rather than
put a trademark (™) symbol in every occurrence of a trademarked name,
we state that we are using the names only in an editorial fashion, and to
the benefit of the trademark owner, with no intention of infringement.
Preface
Contents
Introduction ................................................................................. iv
Printer Firmware........................................................................... iv
Installation Kit.............................................................................. iv
1 Description
General Information ......................................................................2
Media ............................................................................................3
Measures and Weight .....................................................................4
2
Physical Installation
Installation Instructions .................................................................6
3 Fingerprint Control
Activating the Cutter....................................................................10
Controlling the Cut Position........................................................10
4 IPL Control
Activating the Cutter....................................................................12
Cutter Kit (EasyCoder PF4i-series) Installation Instructions iii
Preface
iv Cutter Kit (EasyCoder PF4i-series) Installation Instructions
Introduction
This Installation Instructions booklet describes how to install a cutter in
an EasyCoder PM4i printer.
The installation instructions also describes how to control the cutter in
Intermec Fingerprint and in Intermec Programming Language (IPL).
Printer Firmware
The printer must be fitted with Intermec Fingerprint v8.00 (or later) or
IPL v2.00 (or later).
Installation Kit
The Cutter Kit contains:
•One cutter unit
•One tray
•Three #T20 Torx screws
•One Installation Instruction booklet
The only tool required for the installation is a #T20 Torx screwdriver.
1 Description
Cutter Kit (EasyCoder PF4i-series) Installation Instructions 1
This chapter describes the cutter and provides essen-
tial technical data.
2 Cutter Kit (EasyCoder PF4i-series) Installation Instructions
Chapter 1 — Description
General Information
The cutter is a factory-installed or field-installable option for the Easy-
Coder PM4i printer. The cutter automatically cuts off the media after
printing according to instructions in the controlling firmware. The cut
off portions of media are presented at the front of the cutter and can be
collected on a removable tray.
The cutter can be tilted forward to facilitate media load. As a safety mea-
sure, the cutter can only operate when being completely closed.
The cutter prevents an optional label taken sensor from working, even if
it not necessary to remove it before fitting the cutter.
Tray
Cutter unit
Cutter Kit (EasyCoder PF4i-series) Installation Instructions 3
Chapter 1 —Description
Media
The cutter is primarily intended to cut paper-based media in the form
of continuous stock. It is also possible to cut through the liner between
labels, but be careful not to cut through the labels themselves, because
the adhesive will stick to the cutting blade and may cause malfunction.
Avoid cutting soft plastic-based media.
Minimum media thickness: 78µm
Maximum media thickness: 175µm
4 Cutter Kit (EasyCoder PF4i-series) Installation Instructions
Chapter 1 —Description
Measures and Weight
When a cutter is installed, the measures of the printer are:
The weight is increased by approximately 1.8 kg (4.0 pounds)
150 mm (5.91 in.)
100 mm (3.94 in.)
593 mm (23.35 in.)
747 mm (29.41 in.)
154 mm (6.06 in.)
644 mm (25.35 in.)
160 mm (6.30 in.)
Cutter Kit (EasyCoder PF4i-series) Installation Instructions 5
2 Physical Installation
This chapter describes how to physically install the
cutter in an EasyCoder PM4i printer.
6 Cutter Kit (EasyCoder PF4i-series) Installation Instructions
Chapter 2 —Physical Installation
Installation Instructions
Install the cutter this way:
•Turn the printer upside down on a soft piece of cloth or similar.
•Remove the front door, which is held by two #T20 Torx screws.
•Insert the cutter bracket between the printer’s bottom plate and print
mechanism so the three thread bushings on the bracket fits into the
corresponding holes in the printer’s bottom plate. Fit it using the three
#T20 Torx screws included in the kit.
•Turn the printer back on its feet.
•Open the right-hand door.
•Connect the cutter cable to the Finisher interface connector under-
neath the print mechanism.
•Restart the printer. Bracket
#T20 Torx screws (x3)
Connect to Finisher interface
Otros manuales para PM4I
18
Tabla de contenidos
Otros manuales de Accesorios de impresora de Intermec
Intermec
Intermec UBI EasyCoder 601 E Guía
Intermec
Intermec PM4I Manual de usuario
Intermec
Intermec 869 RFID Reader Instrucciones de funcionamiento
Intermec
Intermec EasyCoder 501 SA Manual de usuario
Intermec
Intermec EasyCoder 501 SA Manual de usuario
Intermec
Intermec EasyCoder PF2i Manual de usuario
Intermec
Intermec PC43t Manual de usuario
Intermec
Intermec EasyCoder PD4 Manual de usuario
Intermec
Intermec 3240 Manual de usuario
Intermec
Intermec EasyCoder PF8 Manual de usuario
Intermec
Intermec EasyCoder PF2i Manual de usuario
Intermec
Intermec CN3 Series Manual de usuario
Intermec
Intermec EasyCoder 501 E Manual de usuario
Intermec
Intermec PB42 Manual de usuario
Intermec
Intermec Font Card Manual de usuario
Intermec
Intermec EasyCoder 3400e Manual de usuario
Intermec
Intermec EasyCoder 3400e Manual de usuario
Intermec
Intermec PB2 Series Manual
Intermec
Intermec PB41 Manual de usuario
Intermec
Intermec EasyCoder 501 SA Manual de usuario
