Intermec 4630 Manual de usuario

Coax/Twinax

Interface Card

User’s Manual

Norand Mobile System Division

P/N 065099-002

IntermecCorporation

6001 36th Avenue West

P.O. Box 4280

Everett, WA 98203-9280

U.S. service and technical support: 1-800-755-5505

U.S. media supplies ordering information: 1-800-227-9947

Canadian service and technical support: 1-800-688-7043

Canadian media supplies ordering information: 1-800-268-6936

Outside U.S. and Canada: Contact your local Intermec service

supplier.

The information contained herein is proprietary and is provided solely

for the purpose of allowing customers to operate and/or service

Intermec manufactured equipment and is not to be released,

reproduced, or used for any other purpose without written permission

of Intermec.

Information and specifications in this manual are subject to change

without notice.

1997 by Intermec Corporation

The word Intermec, the Intermec logo, JANUS, IRL, TRAKKER,

Antares, Duratherm, Precision Print, PrintSet, Virtual Wedge, and

CrossBar are either trademarks or registered trademarks of Intermec

Corporation.

Command Pass-Thruis a trademark of I-O Corporation. The

information in this manual is based on copyrighted material contained

in the I-O 4000 User’s Guide, published by I-O Corporation, Salt Lake

City, Utah.

Throughout this manual, trademarked names may be used. Rather

than put a trademark (or ) symbol in every occurrence of a

trademarked name, we state that we are using the names only in an

editorial fashion, and to the benefit of the trademark owner, with no

intention of infringement.

Contents

iii

Contents

Before You Begin vii

Warranty Information vii

Safety Summary vii

About This Manual viii

Coax Configuration

Using the Interface Card 1-3

Setting the Rotary Switch 1-4

Sending Commands to the Interface Card 1-5

Using a PC to Configure the Interface Card 1-6

Coax Command Listing 1-7

01: Buffer Size 1-8

07: Print Case 1-8

08: LU1 Language 1-9

34: Intervention Required (IR) Timeout 1-10

39: Ending Delimiter Characters 1-10

40: Beginning Delimiter Characters 1-11

41: Alternate Command Identifier 1-12

42: Buffer Hex Dump 1-12

45: SCS TRN Translate 1-13

55: Custom User Strings 1-13

60: Output Protocol 1-14

65: Character Set Selection 1-15

66: Output Port 1-15

70: Overwrite EBCDIC (SCS/LU1)

Translation Table 1-16

71: Overwrite DSC (LU3) Translation Table 1-16

72: Serial Out Baud Rate 1-17

73: Serial Out Word Length 1-17

4630 and 4830 Coax/Twinax Interface Card User’s Manual

74: Serial Out Stop Bits 1-17

75: Serial Out Parity 1-18

98: Restore Factory Defaults, Print Self-Test, or

Restore Previously Defined Settings 1-18

99: Save Configuration in Nonvolatile Memory 1-18

Using the Advanced Features of the Interface Card 1-19

Command Pass-Thru 1-19

Custom User Strings 1-20

SCS Mode Transparent Data 1-20

Twinax Configuration

Configuring the Host 2-3

Using the Interface Card 2-3

Setting the Rotary Switch 2-4

Sending Commands to the Interface Card 2-6

Using a PC to Configure the Interface Card 2-7

Twinax Command Listing 2-8

00: Twinax Address 2-8

01: Alternate CPT Start Delimiter 2-9

02: Alternate CPT End Delimiter 2-9

04: User-Defined Strings 2-10

05: Host Language 2-11

17: Character Set 2-11

24: IBM Printer Emulation 2-12

42: Buffer Hex Dump 2-12

60: Output Protocol 2-13

66: Output Port 2-13

72: Serial Out Baud Rate 2-14

73: Serial Out Word Length 2-14

74: Serial Out Stop Bits 2-14

75: Serial Out Parity 2-15

Contents

98: Restore Factory Defaults, Print Self-Test, and

Restore Previously Defined Settings 2-15

99: Save Current Settings 2-16

Working With User-Defined Command Strings 2-16

Using Command Pass-Thru 2-17

Troubleshooting

Technical Support 3-3

Interface Self-Test 3-3

Buffer Hex Dump 3-4

Diagnostic Loopback 3-5

Twinax Self-Diagnostics 3-6

Common Problems 3-6

Before You Begin

vii

Before You Begin

This section introduces you to standard warranty provisions, safety

precautions, and sources of additional product information.

Warranty Information

To receive a copy of the standard warranty provision for this product,

contact your local Intermec support services organization. In the U.S.

call 1-800-755-5505, and in Canada call 1-800-688-7043. Otherwise,

contact your local Intermec sales organization.

Safety Summary

Your safety is extremely important. Read and follow all warnings and

cautions in this book before handling and operating Intermec

equipment.

Do not repair or adjust alone Do not repair or adjust energized

equipment alone under any circumstances. Someone capable of

providing first aid must always be present for your safety.

First aid Always obtain first aid or medical attention immediately

after an injury. Never neglect an injury, no matter how slight it seems.

Resuscitation Begin resuscitation immediately if someone is injured

and stops breathing. Any delay could result in death. To work on or

near high voltage, you should be familiar with approved industrial

first aid methods.

Energized equipment Never work on energized equipment unless

authorized by a responsible authority. Energized electrical equipment

is dangerous. Electrical shock from energized equipment can cause

death. If you must perform authorized emergency work on energized

equipment, be sure that you comply strictly with approved safety

regulations.

4630 and 4830 Coax/Twinax Interface Card User’s Manual

viii

About This Manual

This manual contains all of the information necessary to operate,

configure, and troubleshoot the 4630 and 4830 coax/twinax interface

card.

What You Will Find in This Manual

For Information On Refer To

Coax configuration Chapter 1, “Coax Configuration,” tells you

how configure the interface card to

communicate with a 3270-type host system

and how to use host download commands to

access the advanced features of the interface

card.

Twinax configuration Chapter 2, “Twinax Configuration,” tells you

how to configure the interface card to

connect to an AS/400 or System 3X host and

how to use host download commands to

access the advanced features of the interface

card.

Troubleshooting Chapter 3, “Troubleshooting,” instructs you

on how to clear error messages and to

troubleshoot programming and

configuration problems with the interface

card.

Manuales populares de Accesorios de impresora de otras marcas

Star Micronics

Star Micronics TSP800 Series Manual de usuario

REA

REA JET HR pro 2K Manual de usuario

HP Laserjet,Color Laserjet 4si Manual de usuario

oliser

oliser MS 45 Manual de usuario

Roland

Roland DU2-64 Instrucciones y recetas

Xerox

Xerox EFI EXP6000 Manual de usuario

Canon

Canon Finisher-T1 Manual de usuario

Sharp

Sharp FO-1MK Manual de usuario

Labelmate

Labelmate PM-300 Manual de usuario

Epson

Epson T6248 Manual de funcionamiento

Epson

Epson OT-BZ20 Manual de usuario

Canon

Canon TonerRobot EP-27 Manual de usuario

Ricoh

Ricoh LCIT RT5100 Guía de inicio rápido

GBC

GBC 16 Series Manual de usuario

Canon

Canon INNER 2-WAY TRAY-E1 Manual de operación y mantenimiento

Develop

Develop SD-509 Manual de usuario

Kyocera

Kyocera KM-6230 Manual

Triumph Adler

Triumph Adler DF-710 Manual