Interlogix TruVision TVA-1101 Manual de usuario
TruVision Covert IP
Camera Installation
Manual
P/N 1072912-EN • REV B • ISS 22MAY15
Copyright © 2015 United Technologies Corporation
Interlogix is part of UTC Building & Industrial Systems, a unit of United
Technologies Corporation. All rights reserved.
Trademarks and
patents
T
rade names used in this document may be trademarks or registered trademarks
of the manufacturers or vendors of the respective products.
Manufacturer Interlogix
2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Certification
N4131
FCC compliance Class A: This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference
(2) This Device must accept any interference received, including interference
that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
ACMA compliance Notice! This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.
Canada This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-0330 du
Canada.
European Union
directives
12004/108/EC (EMC directive): Hereby, UTC Fire & Security declares that this
device is in compliance with the essential requirements and other relevant
provisions of Directive 2004/108/EC.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be
disposed of as unsorted municipal waste in the European Union. For proper
recycling, return this product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated collection points. For
more information see: www.recyclethis.info.
2006/66/EC (Battery directive): This product contains a battery that cannot be
disposed of as unsorted municipal waste in the European Union. See the product
documentation for specific battery information. The battery is marked with this
symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For proper recycling, return the battery to your supplier or to a
designated collection point. For more information see: www.recyclethis.info.
Contact information
For contact information, see www.interlogix.com or
www.utcfssecurityproducts.eu.
Installation Manual 3
Content
Product overview 4
Installation 4
Installation environment 4
Package contents 5
Cable requirements 5
Camera description 6
Which adhesive tape to use 7
Set up the camera 7
Complete the installation 13
Configuration 13
Access the SD card 13
Use the camera with an Interlogix NVR or Hybrid DVR or another system 14
Use the camera with TruVision Navigator 14
Specifications 14
TruVision Covert IP cameras 14
Pin definitions 15
4 Installation Manual
Product overview
This is the installation manual for the following TruVision Covert IP camera
models:
TVA-1101 (1.3MPX IP ATM/covert camera, WDR, PAL)
TVA-3101 (1.3MPX IP ATM/covert camera, WDR, NTSC)
TVL-0101 (TruVision Covert Lens, 1.3MPx, Pinhole, 3.7mm@ F2.3, 2m
cable)
TVL-0102 (TruVision Covert Lens, 1.3MPx, L-shape, 3.7mm@ F2.3, 2m
cable)
TVL-0103 (TruVision Covert Lens, 1.3MPx, Cylinder, 4mm@ F2.0, 2m
cable)
TVL-0104 (TruVision Covert Lens, 1.3MPx, Pinhole, 3.7mm@ F2.3, 8m
cable)
TVL-0105 (TruVision Covert Lens, 1.3MPx, L-shape, 3.7mm@ F2.3, 8m
cable)
TVL-0106 (TruVision Covert Lens, 1.3MPx, Cylinder, 4mm@ F2.0, 8m
cable)
Installation
This chapter provides information on how to install the cameras.
Installation environment
When installing your product, consider these factors:
•Electrical: Install electrical wiring carefully. It should be done by qualified
service personnel. Always use a proper PoE switch or a 12 VDC UL listed
Class 2 or CE certified power supply to power the camera. Do not overload
the power cord or adapter.
•Ventilation: Ensure that the location planned for the installation of the
camera is well ventilated.
•Temperature: Do not operate the camera beyond the specified
temperature, humidity or power source ratings. The operating temperature of
the camera is between -30 to +60°C (-22 to 140°F). Humidity is below 90%.
•Moisture: Do not expose the camera to rain or moisture, or try to operate it
in wet areas. Turn the power off immediately if the camera is wet and ask a
qualified service person for servicing. Moisture can damage the camera and
also create the danger of electric shock.
Installation Manual 5
•Servicing: Do not attempt to service this camera yourself. Any attempt to
dismantle or remove the covers from this product will invalidate the warranty
and may also result in serious injury. Refer all servicing to qualified service
personnel.
•Cleaning: Do not touch the sensor modules with fingers. If cleaning is
necessary, use a clean cloth with some ethanol and wipe the camera gently.
If the camera will not be used for an extended period of time, put on the lens
cap to protect the sensors from dirt.
Package contents
Check the package and contents for visible damage. If any components are
damaged or missing, do not attempt to use the unit; contact the supplier
immediately. If the unit is returned, it must be shipped back in its original
packaging.
Package contents:
•Camera or lens
•Mounting accessories
•Installation manual
•CD with Configuration Manual and TruVision Device Manager
Note:
The ATM/covert camera has no lens in the product package. The lens needs to
be purchased separately according to the application needs. Please notice there
are different cable length and form factors options.
CAUTION: Use direct plug-in UL listed power supplies marked Class 2/CE
certified or LPS (limited power source) of the required output rating as listed on
the unit.
CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose
of used batteries according to the instructions.
Cable requirements
For proper operation, adhere to the following cable and power requirements for
the cameras. Category 5 cabling or better is recommended. All network cabling
must be installed according to applicable codes and regulations.
Recommended power cable requirements to connect the camera:
12 VDC power jack or PoE (802.3af)
6Installation Manual
Camera description
Figure 1: Covert IP camera description
Covert camera unit:
1. Main unit
2. Mounting rack
9. Power indicator
10. Status indicator
11. Link indicator
12. Audio In/Out
13. RJ-12 port
14. Micro SD card slot
15. Reset button
16. Power port
17. PoE and network port
18. RS-232 and alarm port
Lens: (purchased separately)
3. L-shape lens
4. L-shape lens cover
5. L-shape lens mounting bracket
6. Pinhole lens
7. Lens cable with RJ-12 connector
8. Pinhole lens mounting bracket
19. Cylinder lens
20. Cylinder lens mounting bracket
Table 1: LED Indicators
LED Color and Status Indication
POWER Solid red Normal operation
Unlit Power Off
STATUS Solid green Camera works properly
Unlit Camera does not work properly.
Installation Manual 7
LINK Flashing amber Network connection is functioning
properly
Unlit No network connection
Which adhesive tape to use
There are two types of adhesive tape (1 mm and 4 mm) included in the package
that are used to attach the lens to the surface.
1 mm adhesive tape 4 mm adhesive tape
When the surface is around 4 mm
thick, use the 1mm adhesive tape.
The drilling hole should be around
10.5 mm wide.
When the surface is around 1 mm
thick, use the 4mm adhesive tape.
The drilling hole should be around
4.5 mm wide.
Set up the camera
Note: If the light source where the camera is installed experiences rapid, wide-
variations in lighting, the camera may not operate as intended.
To install the main unit:
1. Prepare the mounting surface. The surface should be smooth and clean.
2. Fix the mounting rack on the mounting surface.
8Installation Manual
3. Fix the mounting bracket on the rear panel of the main unit with four screws.
4. Hook the top catch of the main unit on the rack. Gently press the lower part
of the camera against the rack so that it snaps into position on the rack.
Note:If there is already a standard rail installed, you can directly snap the main
unit onto the installed rail.
Installation Manual 9
To install the pinhole lens:
Note: Before installing the device, ensure that the mounting surface is suitable
for adhesive mounting.
1. Drill a hole in the mounting surface.
Note: Please ensure that the hole size is appropriate for the camera lens.
2. Remove the protective film from the adhesive tape on the pinhole lens
mounting bracket. Align the bracket with the drilled hole and stick the
bracket on the mounting surface.
3. Install the pinehole lens into the mounting hole of the mounted bracket.
4. Twist the locking sleeve to lock the lens in place.
10 Installation Manual
To install the L-shape lens
1. Drill a hole in the mounting surface.
2. Remove the protective film from the adhesive tape on the L-shaped
mounting bracket. Align the bracket with the drilled hole and stick the
bracket on the mounting surface.
Note: Please ensure that the hole size is appropriate for the camera lens.
3. Install the L-shape lens into the mounting hole in the bracket then fix the
lens with screws.
Otros manuales para TruVision TVA-1101
2
Este manual sirve para los siguientes modelos
7
Tabla de contenidos
Otros manuales de Cámara de seguridad de Interlogix
Interlogix
Interlogix TVB-5301 Manual de usuario
Interlogix
Interlogix UltraView UVD-6130VE-2 Series Manual de usuario
Interlogix
Interlogix TruVision PTZ 36X Manual de usuario
Interlogix
Interlogix TruVision TVD-2402 Manual de usuario
Interlogix
Interlogix TruVision TVT-2101 Manual de usuario
Interlogix
Interlogix TruVision Open Standards Manual de usuario
Interlogix
Interlogix TruVision TVC-6110-1 Instrucciones de funcionamiento y mantenimiento
Interlogix
Interlogix TruVision TVB-2402 Manual de usuario
Interlogix
Interlogix UltraView PTZ Manual de usuario
Interlogix
Interlogix TVB-WBS Manual de usuario
Interlogix
Interlogix TruVision TVP-5104 Hoja de instrucciones
Interlogix
Interlogix TruVision TVD-2401 Manual de usuario
Interlogix
Interlogix TruVision Line Manual de usuario
Interlogix
Interlogix TVB-2201 Manual de usuario
Interlogix
Interlogix TVD-5125TE-3 Manual de usuario
Interlogix
Interlogix UltraView UVC-6130-1-N Manual de usuario
Interlogix
Interlogix UltraView Manual de usuario
Interlogix
Interlogix TruVision TVB-4410 Manual
Interlogix
Interlogix TruVision TVD-7120VE-2 Manual de usuario
Interlogix
Interlogix UltraView UVD-6130VE-2-P Manual de usuario
