IFM O5P7 Series Manual de usuario
Operating instructions
Retro-reflective sensor
O5P7xx
80284273 / 00 04 / 2019
UK
2
1 Preliminary note
1.1 Symbols used
►Instruction
> Reaction, result
[…] Designation of pushbuttons, buttons or indications
→Cross-reference
Important note
Non-compliance can result in malfunctions or interference.
2 Safety instructions
According to the cULus approval
Caution - Use of controls or adjustments or procedures other than those specified
herein may result in hazardous radiation exposure.
Visible laser light; CLASS 1 LASER PRODUCT.
EN/IEC 60825-1 : 2007 and EN/IEC 60825-1 : 2014 complies with 21 CFR
1040 except for deviations pursuant to Laser Notice No. 50, dated June
2007
Position of the product label Additional label
3 Functions and features
In conjunction with a prismatic reflector or reflective tape the retro-reflective
sensor detects objects and materials without contact and indicates their presence
by a switching signal.
Range 15 m (on prismatic reflector Ø 80 (E20005)).
3
UK
4 Installation
►Fit the prismatic reflector or the reflective tape behind the object to be detected.
►Align the retro-reflective sensor to it and secure it to a bracket.
Maximum range is only possible with precise alignment.
5 Operating and display elements
1: LED
2: [OUT on]
3: [OUT o]
6 Electrical connection
The unit must be connected by a qualified electrician.
►The national and international regulations for the installation of
electrical equipment must be adhered to.
►Voltage supply according to EN 50178.
4
►Disconnect power.
►Connect the unit as follows:
DC PNP
pin 1 = L+ (10...36 V DC)
(pin 2 = not connected)
pin 3 = L-
pin 4 = load (PNP, 200 mA)
7 Settings
7.1 The sensor is to switch when the object is detected
1
►Position the object.
►Press [OUT on] for 2 s.
> The sensitivity is set to the object.
> The yellow LED flashes.
2
►Remove the object.
►Press [OUT off].
> The sensitivity is set without object.
> The yellow LED goes out. The programming is finished.
7.2 The sensor is not to switch when the object is detected
►Position the object (see figure 1) and press [OUT off].
►Remove the object (see figure 2) and press [OUT on].
The setting can also be carried out first without object and then with object.
5
UK
7.3 Setting of the maximum sensitivity
►Align the sensor so that no light is reflected.
The sensor is to switch when the object is detected
►First press [OUT on], then [OUT off].
The sensor is to switch when the object is not detected
►First press [OUT off], then [OUT on].
7.4 Programming unsuccessful
> The LED flashes quickly, 8 Hz.
• Measured value difference too small.
• Max. programming time of 15 min. exceeded.
7.5 Electronic lock
Lock or unlock the buttons
►Press [OUT on] and [OUT off] simultaneously for 10 s.
> Acknowledgement is indicated by a change of the LED status.
8 Operation
►Check whether the unit operates correctly.
> The LED lights when the switching output is switched.
9 Maintenance, repair and disposal
►Keep the front pane of the sensor free from soiling.
►For cleaning do not use any solvents or cleaning agents which could damage
the plastic material.
►Do not try to open the module enclosure. There are no user - serviceable
components inside.
Technical data and further information at www.ifm.com
Tabla de contenidos
Otros manuales de Accesorios de IFM
IFM
IFM VSP003 Manual de usuario
IFM
IFM O3M150 Instrucciones de montaje
IFM
IFM UIT509 Manual de usuario
IFM
IFM Efector 200 O6E4 Manual de usuario
IFM
IFM OID20 Series Manual de usuario
IFM
IFM OGP7 Series Manual de usuario
IFM
IFM UGT203 Manual de usuario
IFM
IFM O5D10 Series Manual de usuario
IFM
IFM Efector 200 O7E2 Series Manual de usuario
IFM
IFM PN01 A Series Manual de usuario
IFM
IFM OGH3 Series Manual de usuario
IFM
IFM Efector 200 O7P2 Series Manual de usuario
IFM
IFM Efector 200 OJ51 Series Manual de usuario
IFM
IFM LK 022 Series Manual de usuario
IFM
IFM SB1 Series Manual de usuario
IFM
IFM Efector 180 IX5030 Manual de usuario
IFM
IFM PN7160 Manual de usuario
IFM
IFM Efector600 TN2531 Manual de usuario
IFM
IFM O3D3 Series Manual de usuario
IFM
IFM DTI424 Manual de usuario
