IFM OGH3 Series Manual de usuario

Este manual sirve para los siguientes modelos

1

Tabla de contenidos

Otros manuales de Accesorios de IFM

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario

Operating instructions

Diffuse reflection sensor

with background suppression

OGH3xx

OGH5xx

UK

704073 / 03 11 / 2019

2

1 Functions and features

The diffuse reflection sensor detects objects and materials without contact and

indicates their presence by a switching signal.

For the range see the type label (on white paper 200x200 mm, 90 % remission).

2 Installation

►Align the diffuse reflection sensor to the object to be detected.

►Secure the unit to a bracket.

The objects to be detected are to move

transversally to the lens of the sensor.

In case of other directions of movement it

should be tested before whether the swit-

ching function is guaranteed.

3 Electrical connection

►Disconnect power.

►Connect the unit as follows.

Cable Connector Pin connection

L+ BN pin 1

L- BU pin 3

load BK pin 4

load *) WH *) pin 2 *)

Core colours BN = brown, BU = blue, BK = black

*) Seulement pour des appareils avec sortie antivalente.

UK

3

4 Operating and display elements

  

1: LED

2: [OUT o󰀨]

3: [OUT on]

4 Settings

4.1 The sensor is to switch when the object is detected

1

►Position the object.

► Press [OUT on] for 2 s.

> The sensitivity is set to the object.

> The LED flashes.

2

►Remove the object.

► Press [OUT off].

> The sensitivity is set without object.

> The LED goes out. The programming is finished.

4.2 The sensor is not to switch when the object is detected

► Position the object (see figure 1) and press [OUT off] for 2

s.

► Remove the object (see figure 2) and press [OUT on].

The settings can also be carried out first without object and then with object.

4

4.3 Programming unsuccessful

> LED flashes quickly, 8 Hz.

Possible causes

• Measured value difference too small.

• Max. programming time of 15 min. exceeded.

4.4 Setting of maximum sensitivity

►Align the sensor so that no light is reflected.

The sensor is to switch when the object is detected

► First press [OUT on] and then [OUT off].

The sensor is to switch when the object is not detected

► First press [OUT off], then [OUT on].

4.5 Locking or unlocking the buttons

The unit can be locked electronically to prevent unintentional settings.

► Press [OUT on] and [OUT off] simultaneously for 

10 s.

> Acknowledgement is indicated by a change of the

LED status.

5 Operation

►Check whether the unit operates correctly.

> The LED lights when the switching output is switched.

6 Maintenance

►Keep the lens of the sensor free from soiling.

►For cleaning do not use any solvents or cleaning agents which could damage

the plastic lens.

Technical data and further information at www.ifm.com

UK

5