ICP DAS USA PROFI-5045 Manual de usuario

PROFI-5053 PROFIBUS DAQ Module - QuickStart (Apr/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

PROFI-5053

PROFIBUS Remote I/O Module

Quick Start Guide

 Introduction

This user guide introduces the user how to implement the PROFI-5000

into their applications in a quick and easy way. Therefore, it only provides

the basic instructions. For more detail information about the PROFI -5000

module, please refer to the PROFI-5000 user manual in the ICP DAS

product CD or download it from ICP DAS web site.

 PROFI-5000 Connector and Pin Assignment

Pin No.

Signal

Meaning

B-Line

Receive/Transmit data – plus

GND

Power ground of active terminator

Power 5 volt of active terminator

A-Line

Receive/Transmit data - minus

The PROFIBUS connector is a standard 9 -pin D-Sub connector, there are

only 4 pins used in PROFI-5000. The pins VP and GND support the 5 volt

power to active terminal resistor, and the A-Line and B-Line is the data bus.

Status Indicator

PROFI-5045/ PROFI-5050/ PROFI-5051/ PROFI-

5052/ PROFI-5053/ PROFI-5055/ PROFI-5060

It provides two types of status indicator, they are PWR

LED (Red) and RUN LED (Green).

Status Indicator

Meaning

Recommend solution

PWR ON

Master not Ready,

1. Check the address setting

Address not Match

of module and DP-master.

RUN OFF

Sets the DP-Master to

Cfg Fault

operation mode.

Make sure of the

consistency of Module

Selection.

PROFI-5053 PROFIBUS DAQ Module - QuickStart (Apr/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

PWR ON &

Module is in clear mode

N/A

RUN ON

or operation mode.

 PROFI-5017/ PROFI-5017C/ PROFI-5018/ PROFI-5024

It provides three types of status indicator, they are PWR

LED (yellow), ERR LED (red) and RUN LED (green).

When the power is supplied to module, PWR LED will

turn on; If CHK_CFG procedure is finished, RUN LED will

turn on and ERR LED will turn off. The table explains the

relationship between them.

Status Indicator

Meaning

Recommend solution

ERR ON &

Offline Mode

Check the address setting of

RUN OFF

module and DP-master.

ERR Flash(0.1 sec)

Stop Mode

Check the DP-Master is ready

to communicate with module.

Check the setting of module in

ERR Flash(0.5 sec)

Prm Fault

the master interface and make

sure of the consistency.

ERR Flash(1 sec)

Cfg Fault

Same as above

ERR ON & RUN

Clear Mode

Sets the DP-Master from clear

mode to operation mode

ERR OFF &

Operate Mode

RUN ON

PWR &

Diag Exist

Check the Input/Output value

ERR Flash

(Diag. Msg.

that if exceed/under the limit

lnterlace(0.5 sec)

Request)

PROFI-5053 PROFIBUS DAQ Module - QuickStart (Apr/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

 Terminating Resistors

In order to minimize the reflection effect of the signal transmission, PROFIBUS

device has to fit with an active terminal resistor at both first node and last node.

The connection of active terminating resistors is shown in above circuit diagram.

The PROFI-5000 doesn’t have any terminating resistors inside. Therefore, users

must add the terminator in external. In general, PROFIBUS connector has

terminating resistors inside, and there is a switch to control the ON/OFF of the

terminating resistors, as shown below.

Terminator ON

Terminator OFF

Terminator Switch

 Node Address

According to PROFIBUS specification, the station address which from 0 to 126 is

valid, and the address 126 is a special address that supports the remote setting

SSA telegram from Class 2 DP-Master.

 PROFI-5045/ PROFI-5050/ PROFI-5051/ PROFI-5052/

PROFI-5053/ PROFI-5055/ PROFI-5060

PROFI-5053 PROFIBUS DAQ Module - QuickStart (Apr/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

-The figure shown above is the decimal rotary switch. It dominates

the node (station) address of PROFI-5000. The left side switch is

high nibble of address and the other one is low nibble of address.

- It doesn’t support SSA service for setting node address.

EX 1 : MSB = 2, LSB = 3, node address => (2*10+3) = 23

 PROFI-5017/ PROFI-5017C/ PROFI-5018/ PROFI-5024

- The figure shown above is the decimal rotary switch. It dominates

the node (station) address of PROFI-5000. The switch is which

labeled MSB is high nibble of address and the other one is low

nibble of address.

- Module applies the setting of rotary switch as its address if the

address is valid. While the address is invalid, module loads the pre-

saved value from EEPROM. Moreover, if the address is invalid

(126) again, module awaits the SSA telegram and applies it. (Note:

If you want to clear the setting stored at EEPROM, you just adjust

rotary switch to FF before the power supplied).

Rotary

Pre-saved address

SSA Telegram

PROFI-5017(C)

Switch(dec)

(EEPROM)

Station Address

0~125

Do not care

No Accept

Rotary Switch

126~254

0~125

No Accept

Pre-saved

address(EEPROM)

126(default)

Accept with

SSA Telegram and

address 0~125

save address to

EEPROM

127~254

impossible

N/A

255

Clear to 126

Accept with

SSA telegram and

address 0~125

save address to

EEPROM

EX 1 : MSB = 0, LSB = B, node address => (0*16+11) = 11

EX 2 : MSB =7, LSB = 9, node address => (7*16+9) = 121

PROFI-5053 PROFIBUS DAQ Module - QuickStart (Apr/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

 PROFI-5000 – Setting and Module installation

(example for SIMATIC Step 7)

The following steps can help users to set and apply the PROFI-5000.

1. Address Setting:

2. Load GSD file into the DP-Master Configuring software a.

Open HW Config

b. Select Option -> Install GSD files

c. Click “Browse” to select GSD file, and then click “Install”

PROFI-5053 PROFIBUS DAQ Module - QuickStart (Apr/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

d. Install OK

3. Select I/O modules

a. Choose PROFI-5000

b. add I/O module that you want to use.

PROFI-5053 PROFIBUS DAQ Module - QuickStart (Apr/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

c. Modify system parameters and module parameters(modify by user’s

preference)

 System parameters: Double click PROFI-5000

 Module parameters: Double click module

4. Download Setting and Program into DP-Master

Users load the setting and program into DP-Master, and let it go.

a. Select Station -> Save and Compile

PROFI-5053 PROFIBUS DAQ Module - QuickStart (Apr/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

b. Select PLC -> Download

After the procedure finish, DP-Master will establish the connection with

PROFI-5000 and execute program automatically. RUN_LED indicates the

status of connection that you can observe.

PROFI-5053 PROFIBUS DAQ Module - QuickStart (Apr/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

PROFI-5000 Quick Start (Version 2.1, June/2013) ------8

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unidad de control de ICP DAS USA

ICP DAS USA

ICP DAS USA HRT-370 Manual de usuario

ICP DAS USA

ICP DAS USA tSH-735 Manual de usuario

ICP DAS USA

ICP DAS USA ECAT-2011H Manual de usuario

ICP DAS USA

ICP DAS USA ET-7000 series Manual de usuario

ICP DAS USA

ICP DAS USA GTM-204M-4G Manual de usuario

ICP DAS USA

ICP DAS USA tET-P2A2 Manual de usuario

ICP DAS USA

ICP DAS USA PET-7053 Manual de usuario

ICP DAS USA

ICP DAS USA tSH-734 Manual de usuario

ICP DAS USA

ICP DAS USA WF-2051 Manual de usuario

ICP DAS USA

ICP DAS USA iWSN-110X Series Manual de usuario

ICP DAS USA

ICP DAS USA EIP-2000 Series Manual de usuario

ICP DAS USA

ICP DAS USA MDC-700 Series Manual de usuario

ICP DAS USA

ICP DAS USA I-7080 Manual de usuario

ICP DAS USA

ICP DAS USA 7188EN Guía de instalación

ICP DAS USA

ICP DAS USA M-7053D Manual de usuario

ICP DAS USA

ICP DAS USA PDS-220F Series Manual de uso y cuidado

ICP DAS USA

ICP DAS USA M-7041D Manual de usuario

ICP DAS USA

ICP DAS USA I-7083 Manual de usuario

ICP DAS USA

ICP DAS USA ZT-2053 Manual de usuario

ICP DAS USA

ICP DAS USA ECAT-2051 Manual de usuario

ICP DAS USA

ICP DAS USA ET-87P2 Manual de usuario

ICP DAS USA

ICP DAS USA GTP-230 Manual de usuario

ICP DAS USA

ICP DAS USA GW-7552-M Manual de usuario

ICP DAS USA

ICP DAS USA ET-2200 Series Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario