ICP DAS USA I-7080 Manual de usuario

I-7080 2 Ch Counter / Frequency Input DAQ Module - QuickStart (Apr/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

I-7080

2 Channel Counter / Frequency Input Data

Acquisition Module

Quick Start Guide

Product Website:

https://www.icpdas-usa.com/_data_acquisition_i_7080.html

http://www.icpdas-usa.com/dcon_utility_pro.html

1. Introduction

I-7080 is intelligently designed to provide signal conditioning system monitoring and safe value

settings. I-7080 is a cost-effective solution for a wide range of valuable industrial control signals

and systems. The DCON utility can help users to configure and test I-7080 High Speed Counter /

Frequency Input module. Plenty of library functions and demo programs are provided to let

users develop programs easily under Windows, Linux and DOS operating systems. The

communication interface is modbus protocol via RS-485. Users may mount the modules on a

DIN rail, panel or wall. Modules have a screw-terminal block to connect to the signals.

2. Terminal Assignment

I-7080 2 Ch Counter / Frequency Input DAQ Module - QuickStart (Apr/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

3. Block/ Wiring Diagram

4. Default Settings

Default settings for the I-7080 module is as follows:

•address=01

•baud rate=9600

•checksum disable

•data=1 start+8 data+1 stop(no parity)

•type=50 (counter input)

•alarm=hi alarm on counter 0 & counter 1 (I-7080)

I-7080 2 Ch Counter / Frequency Input DAQ Module - QuickStart (Apr/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. Configuration

To install the module, follow the steps below:

1. Connect the analog output.

2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals. If

the host is only equipped with an RS-232 interface, then an RS-232 to RS-485

converter will be required.

3. Connect the module to the power supply using the +Vs and GND terminals. Note that

the voltage supplied should be in the range of +10 to +30V DC.

I-7080 2 Ch Counter / Frequency Input DAQ Module - QuickStart (Apr/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4. Open DCON utility pro

click on COM port(first icon).

It can select multi-options such as Baud Rate, Protocol, Checksum, and Format to

search module. The default settings for the module can be found in Section 3. Click OK

after selecting the COM port setting.

I-7080 2 Ch Counter / Frequency Input DAQ Module - QuickStart (Apr/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. DCON utility pro will search for the selected COM port according the setting

previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS

and the others modules.

6. Configuration I/O module setting on PC

I-7080 2 Ch Counter / Frequency Input DAQ Module - QuickStart (Apr/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

7. For I-7000 modules, DCON utility pro terminal can send command to the module.

See user manual Sections 2 for details command.

Configure the module: sending the %AANNTTCCFF command. See user manual

Section 2 for details.

Read data from the input channels: send either the #AA or #AAN command to the

module.

8. If user doesn’t know command, user can select Address and ID, it will show some

refer commands as below. User can select necessary command to test or debug

modules.

Otros manuales para I-7080

Tabla de contenidos

Otros manuales de Unidad de control de ICP DAS USA

ICP DAS USA

ICP DAS USA M-7069D Manual de usuario

ICP DAS USA

ICP DAS USA ET-7000 series Manual de usuario

ICP DAS USA

ICP DAS USA ZT-2017 Manual de usuario

ICP DAS USA

ICP DAS USA ET-2260 Manual de usuario

ICP DAS USA

ICP DAS USA WP-5231 Manual de usuario

ICP DAS USA

ICP DAS USA DS-700 Series Manual de usuario

ICP DAS USA

ICP DAS USA PM-4324 Series Manual de usuario

ICP DAS USA

ICP DAS USA I-7063 Manual de usuario

ICP DAS USA

ICP DAS USA I-8123W Guía de configuración

ICP DAS USA

ICP DAS USA DL-10 Manual de usuario

ICP DAS USA

ICP DAS USA Zigbee ZT-2060 Manual de usuario

ICP DAS USA

ICP DAS USA tSH-700 Series Manual de usuario

ICP DAS USA

ICP DAS USA tM-AD4P2C2 Manual de usuario

ICP DAS USA

ICP DAS USA I-8026W Manual de usuario

ICP DAS USA

ICP DAS USA ECAT-201x EtherCAT Slave I/O Manual de usuario

ICP DAS USA

ICP DAS USA ECAT-2050 Manual de usuario

ICP DAS USA

ICP DAS USA LP-8 4 Series Instrucciones generales

ICP DAS USA

ICP DAS USA M-7024 Manual de usuario

ICP DAS USA

ICP DAS USA tET-P2A2 Manual de usuario

ICP DAS USA

ICP DAS USA I-7080 Manual de usuario

ICP DAS USA

ICP DAS USA SG-3784M Manual de usuario

ICP DAS USA

ICP DAS USA SG-3071 Manual de usuario

ICP DAS USA

ICP DAS USA PDS-220F Series Manual de uso y cuidado

ICP DAS USA

ICP DAS USA PM-3133i Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario