ICP DAS USA 7188EN Guía de instalación

分類/Classification

tDS

tGW

PETL/tET/tPET

DS/PDS/PPDS

tM-752N

I/O Card

VXC Card

VxComm

7188EN

作者/Author

Tammy

日期/Date

2016-01-12

編號/NO.

FAQ-043

Q: How to enable web server for the PDS/7188EN series module?

A: The PDS/7188EN series module contains a built-in web server that allows the settings for the module to

be remotely modified via a web interface. When the web server has been disabled (Web Server = 0), refer

to the following two methods to enable the web server.

Method 1: Enable web server on PDS by using “console port and command”.Follow the procedure

described below:

1. Power off the PDS module.

2. Connect the download-cable (CA0910), between the PDS and COM4 of the development PC.

3. Wire the CA-0910 to PDS, as follows:

Connect the CA-0910.TX with PDS.TxD

Connect the CA-0910.RX with PDS.RxD

Connect the CA-0910.GND with PDS.GND

4. Set the “Init/Normal Switch”on the PDS module to the in “Init”position.

(Or connect the INIT* pin to the GND pin.)

5. Power on the PDS module.

6. Unzip the “7188XW_yyyymmdd.zip” file on the PC. The “7188XW_yyyymmdd.zip”can be obtained

from the ICP DAS web site (http://ftp.icpdas.com/pub/cd/8000cd/napdos/minios7/utility/).

7. Open “Notepad”text editor for Windows and type the command: C4 B115200 P0D8 S1, and then save

the file as “7188xw.ini”in the same directory of 7188XW.exe.

8. Execute “7188XW.EXE”and press [Enter] key.

9. Settings configuration command:

The following is an example of a HTTP configuration.

Command

Description

HTTP= 1

Enables the Web Server.

HTTP= 0

Disables the Web Server.

Enable Web Server

C: COM Port of the development PC (e.g., C4)

B: Baud Rate (e.g., B115200)

P: Parity None (e.g., P0)

D: Data Bits (e.g., D8)

S: Stop Bits (e.g., S1)

Method 2: Enable web server on PDS by using “TCP port 10000”.Follow the procedure described below:

1. Ensure that the network settings on the Host PC have been correctly configured and are functioning

normally. Connect both the PDS module and the Host PC to the same sub network or the same

Ethernet Switch, and apply power to the PDS module.

2. Configure the correct network settings for the required PDS module. Refer to PDS Quick Start Guide for

more detailed information.

(http://ftp.icpdas.com/pub/cd/8000cd/napdos/pds/pds-700/document/quick_start/)

3. Download the “Terminal.exe”on your PC, or use other telnet client program. The “Terminal.exe”can

be downloaded from the ICP DAS web site.

(http://ftp.icpdas.com/pub/cd/tinymodules/napdos/software/)

4. Double click the “Terminal.exe”to open “Configuration Settings”dialog box.

5. Click the “TCP/IP Port”tab to configure the parameters as follows:

5-1: Type the “IP address of the PDS module”in the “IP Address”field.

5-2: Type the “10000”in the “TCP/IP Port”field.

5-3: Click the “Open COM”button.



6. Select the “Hex/Text”option in the “Display”filed and settings configuration command:

Command

Description

26SAVE=1, HTTP=1

Enables the Web Server and save the configuration to EEPROM.

26SAVE=1, HTTP=0

Disables the Web Server and save the configuration to EEPROM.

7. Type the “26SAVE=1, HTTP=1”string in the “send”field then click the “Send”button.

8. If the response is received, it will be displayed in the received field that means the success.

9. Reboot the PDS module to complete the configuration.







Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unidad de control de ICP DAS USA

ICP DAS USA

ICP DAS USA ECAT-2061 Manual de usuario

ICP DAS USA

ICP DAS USA ET-7200 Series Manual de usuario

ICP DAS USA

ICP DAS USA tM-AD8C Manual de usuario

ICP DAS USA

ICP DAS USA I-7045D Manual de usuario

ICP DAS USA

ICP DAS USA PM-3133i Manual de usuario

ICP DAS USA

ICP DAS USA M-7069D Manual de usuario

ICP DAS USA

ICP DAS USA MDC-700 Series Manual de usuario

ICP DAS USA

ICP DAS USA I-7088 Manual de usuario

ICP DAS USA

ICP DAS USA PDS-5000 Series Manual de usuario

ICP DAS USA

ICP DAS USA M-7026 Manual de usuario

ICP DAS USA

ICP DAS USA PM-3133-RCT Series Manual de usuario

ICP DAS USA

ICP DAS USA ECAT-2011H Manual de usuario

ICP DAS USA

ICP DAS USA MN-3253 Series Manual de usuario

ICP DAS USA

ICP DAS USA SG-3071 Manual de usuario

ICP DAS USA

ICP DAS USA M-7069 Manual de usuario

ICP DAS USA

ICP DAS USA I-8092F Manual de lista de piezas

ICP DAS USA

ICP DAS USA GTP-230 Manual de usuario

ICP DAS USA

ICP DAS USA I-8213W-4G Manual de usuario

ICP DAS USA

ICP DAS USA tZT-P4C4 Manual de usuario

ICP DAS USA

ICP DAS USA PM-3033 Series Manual de usuario

ICP DAS USA

ICP DAS USA ZT-2570 Manual de usuario

ICP DAS USA

ICP DAS USA I-8123W Guía de configuración

ICP DAS USA

ICP DAS USA M-7051 Manual de usuario

ICP DAS USA

ICP DAS USA I-7188XA Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario